WESTECH KOREA, INC.
ROCKWELL K56FLEX
|
Card Type |
Modem |
|
Chip Set |
Rockwell |
|
Maximum Modem Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32ter, V.32bis, V.34, V.90 |
|
Fax Modulation Protocol |
ITU-T V.17, V.21 CH2, V.27ter, V.29, V.33 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
I & II |
|
Data Bus |
PCMCIA |
55306
|
SUPPORTED COMMAND SET | |
|
Basic AT Commands | |
|
AT, A/ | |
|
A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z | |
|
&C, &M, &P, &Q, &R, &T, &W, &X, &Y, &Z | |
|
Extended AT Commands | |
|
\A, \B, \K, \N, \V | |
|
%C, %E, %L, %Q | |
|
Special Commands | |
|
+MS, -K, #CID | |
|
S Registers | |
|
S0, S1, S2, S3, S4, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S22, S23, S24, S25, S26, S27 | |
|
S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92, S95 | |
|
Note: |
See MHI Help File for full command documentation. Specific S-register information unavailable; S-registers may vary slightly from MHI help file. |
PROPRIETARY AT COMMAND SET
|
AUTO-MODE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
|
Command |
Function |
|
N0 |
Auto-mode detection disabled. Handshake begins at line speed designated by the S37 register. If S37=0 handshake follows interface speed |
|
N1 |
Auto-mode detection enabled. Handshake begins at line speed designated by the S37 register. If S37=0 handshake at highest possible speed with fallback to lower speed if necessary |
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Fn [cmds] |
|
Description: |
Selects the communication protocol for data calls |
|
Command |
Protocol |
|
F0 |
Auto-mode detection enabled |
|
F1 |
V.21 or Bell 103 |
|
F2 |
Reserved |
|
F3 |
V.23 |
|
F4 |
V.22 or Bell 212/A at 1200bps |
|
F5 |
V.22bis |
|
F6 |
V.32 or V.32bis at 4800bps |
|
F7 |
V.32bis at 7200bps |
|
F8 |
V.32 or V.32bis at 9600bps |
|
F9 |
V.32bis at 12.0Kbps |
|
F10 |
V.32bis at 14.4Kbps |
|
CONFIGURATION PROFILES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &V [cmds] |
|
Description: |
Displays active and stored configuration profiles |
|
Command |
Function |
|
&V0 |
Display current configurations |
|
&V1 |
Display connection statistics |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
&S1 |
DSR high only while modem is handshaking or connected |
|
DATA TERMINAL READY (DTR) | |||||
|
Type: |
Configuration | ||||
|
Format: |
AT [cmds] &Dn [cmds] | ||||
|
Description: |
Selects modem response to DTR | ||||
Note: The action each variant of &D causes depends on the setting of &Q | |||||
|
&Q Setting |
&D0 |
&D1 |
&D2 |
&D3 | |
|
&Q0, &Q5, &Q6 |
Command 0 |
Command 1 |
Command 2 |
Command 4 | |
|
&Q1, &Q4 |
Command 2 |
Command 1 |
Command 2 |
Command 4 | |
|
&Q2, &3 |
Command 2 |
Command 2 |
Command 2 |
Command 2 | |
|
Command |
Function | ||||
|
Command 0 |
Modem does not respond to DTR | ||||
|
Command 1 |
Modem goes to command mode after DTR goes is off | ||||
|
Command 2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. | ||||
|
Command 3 |
Modem is initialized after DTR goes off | ||||
|
FACTORY DEFAULT PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &F [cmds] |
|
Description: |
Sets values in active profile to values found in the default profile |
|
Command |
Function |
|
&F0 |
Load factory configuration 0 |
|
&F1 |
Load factory configuration 1 |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables flow control options |
|
Command |
Function |
|
&K0 |
Flow control disabled |
|
&K3 |
RTS/CTS flow control enabled |
|
&K4 |
XON/XOFF flow control enabled |
|
&K5 |
Transparent XON/XOFF flow control enabled |
|
&K6 |
Unidirectional XON/XOFF flow control enabled |
|
GUARD TONE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Gn [cmds] |
|
Description: |
Commands the modem to transmit a guard tone in V.22/V.22bis |
|
Command |
Function |
|
&G0 |
Guard tone disabled |
|
&G1 |
Guard tone disabled |
|
&G2 |
1800Hz guard tone enabled |
|
JACK TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Jn [cmds] |
|
Description: |
For purposes compatibility only. Performs no function |
|
LINE TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Ln [cmds] |
|
Description: |
Selects line type |
|
Command |
Line Type |
|
&L0 |
Switched line (PSTN/Dial-up) |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product code |
|
I1 |
Reports ROM checksum |
|
I2 |
Tests and reports ROM checksum |
|
I3 |
Reports firmware version and application codes |
|
I4 |
Reports OEM identifier string in either binary or ASCII format |
|
I5 |
Reports country code |
|
I6 |
Reports data pump model and internal code |
|
I7 |
Reports DAA code |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
|
TRANSMIT CARRIER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Cn [cmds] |
|
Description: |
Command non-functional; for compatibility only. Returns OK |
SPECIAL COMMANDS
|
BLACKLIST | |
|
Type: |
Immidiate |
|
Format: |
AT [cmds] *B [cmds] |
|
Description: |
Displays blacklisted numbers. If no numbers are blacklisted, returns OK. |
|
COUNTRY SELECT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] *NCn [cmds] |
|
Range: |
1 - 8 |
|
Description: |
Selects country code from NVRAM |
|
DELAY | |
|
Type: |
Immidiate |
|
Format: |
AT [cmds] *D [cmds] |
|
Description: |
Displays delayed numbers with the delay associated with each. If no numbers are delayed, returns OK. |
|
DISTINCTIVE RING | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] -SDR=n [cmds] |
|
Description: |
Selects the distinctive ring settings |
|
Command |
Function |
|
-SDR=0 |
Distinctive ring disabled |
|
-SDR=1 |
Type 1 enabled |
|
-SDR=2 |
Type 2 enabled |
|
-SDR=3 |
Type 1 and 2 enabled |
|
-SDR=4 |
Type 3 enabled |
|
-SDR=5 |
Type 1 and 3 enabled |
|
-SDR=6 |
Type 2 and 3 enabled |
|
-SDR=7 |
Type 1, 2, and 3 enabled |
|
FLASH MEMORY | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] **n [cmds] |
|
Description: |
Controls download to flash memory |
|
Command |
Function |
|
**0 |
Downloads into flash memory at last sensed speed |
|
**1 |
Downloads into flash memory at 38.4Kbps |
|
**2 |
Downloads into flash memory at 57.6Kbps |
|
MNP10 - POWER LEVEL ADJUST | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -SEC=n [cmds] |
|
Range: |
0-30 |
|
Unit: |
-1dBm |
|
Description: |
Controls automatic transmit power level adjustment during MNP 10 link negotiation |
|
Command |
Function |
|
-SEC=0 |
MNP10 disabled. Transmission level is set in the S91 register |
|
-SEC=1, [tx_lev] |
MNP10 enabled. Set transmit level |
|
PLUG & PLAY SERIAL NUMBER | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %7n [cmds] |
|
Range: |
8 |
|
Unit: |
Hexidecimal |
|
Description: |
Sets and stores numbers for serial plug & play |
|
PLUG & PLAY VENDOR ID & PRODUCT NUMBER | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %8n [cmds] |
|
Range: |
3 (ASCII), 4 (hex) |
|
Unit: |
ASCII, Hexidecimal |
|
Description: |
Sets and stores numbers for serial plug & play |
|
RPI/VIDEO READY MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] +Hn [cmds] |
|
Description: |
Enables/disables RPI & video ready mode |
|
Command |
Function |
|
+H0 |
RPI/video ready mode disabled |
|
+H1 |
RPI at 19.2Kbps DTE speed enabled |
|
+H2 |
RPI at 38.4Kbps DTE speed enabled |
|
+H3 |
RPI at 57.6Kbps DTE speed enabled |
|
+H11 |
RPI + mode enabled |
|
+H16 |
Video ready mode enabled |
S(STATUS) -REGISTERS
|
AUTOSYNC OPTIONS | |
|
Type: |
Register |
|
Format |
AT [cmds] S19=n [cmds] |
|
Description: |
Sets autosync options. Further information is unavailable |
|
AUTOSYNC/SYNC | |
|
Type: |
Register |
|
Format |
AT [cmds] S20=n [cmds] |
|
Range: |
0-255 |
|
Unit: |
Unidentiified |
|
Description: |
Sets autosync HDLC address or BSC sync character. Further information is unavailable |
|
BIT-MAPPED REGISTER S21 | |
|
Type: |
Register |
|
Format |
AT [cmds] S21=n [cmds] |
|
Range: |
Unidentiified |
|
Description: |
Selects V.24/General bit mapped options. Further information is unavailable |