Card Type	Modem (asynchronous), Ethernet
Chipset	Intel 82595TX
Maximum Onboard Memory	160KB DRAM/128KB PROM
Network Transfer Rate	10Mbps
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I & II
Data Modulation	Bell 103A/212A ITU-T V.21, V.22, V.23, V.22bis, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation	Unidentified
Error Correction/Compression	MNP5, MNP10, V.42, V.42bis
Topology	Star
Wire Type	Unshielded twisted pair
Boot ROM	Not available

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, A/

A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \G, \J, \K, \L, \N

%C, %L, %Q

Special AT Commands

-K, -Q, *H, )M, @M, :E, +MS

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25,

S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S91,

S92, S95, S201

AUTO-RETRAIN AND AUTO-FALLBACK/FALL-FORWARD
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode and fallback/fall-forward
Command	Function
í %E0	Auto-retrain disabled.
%E1	Auto-retrain enabled.
%E2	Auto-fallback/fall-forward enabled.
%E3	Auto-retrain and fast disconnect enabled.

AUTOSYNC
Format		AT [cmds] S19=n [cmds]
Default:		0
Range:		0 - 63
Unit:		Bit-mapped
Description:		Sets options for Hayes AutoSync functions.
Bit	Value	Function
0	0	Not used.
1	í 0 1	BSC enabled. HDLC enabled.
2	í 0 1	HDLC address detection disabled. HDLC address detection enabled.
3	í 0 1	NRZI bit encoding enabled. NRZ bit encoding enabled.
4	í 0 1	Mark idle enabled. Flag or sync idle enabled.

AUTOSYNC HDLC ADDRESS
Type:	Register
Format:	AT [cmds] S20=n [cmds]
Default:	0
Range:	0-255
Unit:	Unidentified
Description:	Sets the HDLC address or BSC character.

COUNTRY CODE
Type:	Configuration
Format:	AT [cmds] *NCnn [cmds]
Description:	Changes the country code of the modem to nn.

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DJ	MNP10 link will be negotiated at 1200bps for this call.
DK	MNP10 power level adjustment enabled for this call.
DL	Re-dial last number.
DP	Pulse dialing enabled.
DR	Answer mode enabled; originate mode disabled following handshake initiation.
DS=n	Dial stored telephone number n.
DT	Tone dialing enabled.
DW	Dialing resumed following dial tone detection.
D,	Dialing paused for amount of time specified in S8 register.
D"WXY"	Optional method of denoting telephone numbers. Letters enclosed in quotes are interpreted as numbers according to the system found on a telephone keypad.
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D$	Wait for prompt tone detection function enabled. Modem waits for prompt tone for amount of time specified by the S7 command.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.
D^	Calling tone toggled from current setting for this call.

PULSE DIAL CODE
Type:	Configuration
Format:	AT [cmds] *Zn [cmds]
Description:	Sets the currently active pulse dialing code.
Command		Function
í *Z0		Use dial code 0.
*Z1		Use dial code 1.

DISPLAY STORED NUMBERS
Type:	Immediate
Format:	AT [cmds] \F [cmds]
Description:	Displays all stored phone numbers.

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] &Kn [cmds]
Description:	Enables flow control options.
Command	Function
&K0	Flow control disabled.
í &K3	RTS/CTS flow control enabled.
&K4	XON/XOFF flow control enabled.
&K5	Transparent XON/XOFF flow control enabled.
&K6	RTS/CTS and XON/XOFF flow control enabled.

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports modem model and speed
I1	Reports ROM checksum
I2	Tests and reports ROM checksum
I3	Reports firmware revision.
I5	Reports country code.

REQUEST LIST OF FORBIDDEN NUMBERS
Type:	Immediate
Format:	AT [cmds] *B [cmds]
Description:	Requests the list of forbidden numbers from the modem.

REQUEST LIST OF DELAYED NUMBERS
Type:	Immediate
Format:	AT [cmds] *D [cmds]
Description:	Requests the list of delayed numbers from the modem.