Card Type	Fax, Modem (asynchronous)
Chip Set	Unidentified
Maximum Modem Rate	14.4Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I & II
Data Modulation Protocol	Bell 103A/212A ITU-T V.21,V.22, V.22bis,V.32, V.32bis
Fax Modulation Protocol	ITU-T V.17, V.21 ch2, V.27ter, V.29
Error Correction/Compression	MNP2-5, V.42, V.42bis
Boot ROM	Not available

BIT-MAPPED REGISTER S14
Format:		AT [cmds] S14=n [cmds]
Default:		170
Range:		0-239
Unit:		Bit-mapped
Description:		Controls echo, result codes and display, dial mode, and answer/originate mode.
Bit	Value	Function
0	í 0 1	On-line state character echo disabled On-line state character echo enabled
1	0 í 1	Command echo disabled Command echo enabled
2	í 0 1	Result codes disabled Result codes enabled
3	0 í 1	Display result codes in numeric format Display result codes in verbose format
4	í 0	Not used
5	0 í 1	Tone dial enabled Pulse dial enabled
6	í 0 1	Result codes disabled/enabled as set by bit 2 or Qn Result codes enabled in originating mode
7	0 í 1	Answer mode enabled Originate mode enabled

BIT-MAPPED REGISTER S21
Format		AT [cmds] S21=n [cmds]
Default:		Unidentified
Range:		0-255
Unit:		Bit-mapped
Description:		Selects jack type, CTS/DCD/DSR signals, low DTR action, and the long space disconnect function.
Bit	Value	Function
0	0 1	Selects RJ-11, RJ-41S, or RJ45S jack Selects RJ-12 or RJ-13 jack
1	0 1	User profile 0 User profile 1
2	0 1	CTS follows RTS CTS forced high
4, 3	00 01 10 11	DTR signal ignored Modem goes to command mode on low DTR Modem disconnects on low DTR; Auto-Answer is disabled. Modem is initialized on low DTR
5	0 1	DCD forced high DCD normal
6	0 1	DSR forced high DSR normal
7	0 1	Long space disconnect function disabled Long space disconnect function enabled

BIT-MAPPED REGISTER S23
Format		AT [cmds] S23=n [cmds]
Default:		Unidentified
Range:		0-191
Unit:		Bit-mapped
Description:		Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone.
Bit	Value	Function
0	0 1	Remote digital loopback denied Remote digital loopback allowed
3 - 1	000 001 010 011 100 101 110 111	Sets serial port speed to 0-300bps Sets serial port speed to 600bps Sets serial port speed to 1200bps Sets serial port speed to 2400bps Sets serial port speed to 4800bps Sets serial port speed to 9600bps Sets serial port speed to 19.2Kbps Sets serial port speed to 38.4Kbps
5, 4	00 01 10 11	Parity even Not used Parity odd No Parity
7, 6	00 01 10	Guard tone disabled Guard tone 550Hz enabled Guard tone 1800Hz enabled

BIT-MAPPED REGISTER S41
Format		AT [cmds] S41=n [cmds]
Default:		1
Range:		0-7
Unit:		Bit-mapped
Description:		Selects compression, auto-retrain, flow control, and MNP mode.
Bit	Value	Function
0	0	Data compression disabled
	í 1	Data compression enabled
1	í 0	Auto-retrain disabled
	1	Auto-retrain enabled
2	í 0	Stream mode for MNP
	1	Block mode for MNP
7-3		Not used

BIT-MAPPED REGISTER S40
Format		AT [cmds] S40=n [cmds]
Default:		Unidentified
Range:		0-255
Unit:		Bit-mapped
Description:		Controls power level and break handling; selects MNP extended services, link negotiation, and block size.
Bit	Value	Function
1,0	00	Normal mode enabled
	01	Normal mode enabled
	í 10	MNP reliable mode enabled
	11	Auto-reliable mode or MNP auto-reliable mode enabled
4, 3, 2	000	\K0
	001	\K1
	010	\K2
	011	\K3
	100	\K4
	í 101	\K5
6, 5	00	MNP block size is 64 characters
	01	MNP block size is 128 characters
	10	MNP block size is 192 characters
	11	MNP block size is 256 characters
7	0	Flow control disabled
	1	Flow control enabled

COMMUNICATION PROTOCOLS
Type:	Configuration
Format:	AT [cmds] Bn [cmds]
Description:	Selects the communication protocol for data calls
Note:	The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols.
Command	Protocol
B0	ITU-T V.22 and V.21 at 300 or 1200bps
B1	Bell 212A and 103 at 300 or 1200bps

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DL	Re-dial last number
DP	Pulse dialing enabled
DR	Answer mode enabled; originate mode disabled following handshake initiation.
DS=n	Dial stored telephone number n
DT	Tone dialing enabled/Pulse dialing disabled
DW	Dialing resumed following dial tone detection
D,	Dialing paused for amount of time specified in S8 register
D^"	Call tone turned on
D!	Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook.
D@	Wait for Quiet Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string.
D;	Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command.

DATA SET READY (DSR)
Type:	Configuration
Format:	AT [cmds] &Sn [cmds]
Description:	Selects DSR options
Command	Function
&S0	DSR forced high
&S1	DSR set to operate at EIA-232-D specifications

DCE LINE SPEED
Type:	Register
Format	AT [cmds] S37=n [cmds]
Description:	Sets the maximum allowable data exchange rate attempted during handshake process.
Command	Function
í S37=0	Speed of last connection
S37=1	300bps
S37=2	300bps
S37=3	300bps
S37=4	Reserved
S37=5	1200bps
S37=6	2400bps
S37=7	Reserved
S37=8	4800bps
S37=9	9600bps
S37=10	12.0Kbps
S37=11	14.4Kbps
S37=12	7200bps

DTR CHANGE THRESHOLD
Type:	Register
Format	AT [cmds] S25=n [cmds]
Default:	5
Range:	0-255
Unit:	.01 second
Description:	Sets maximum time a change in the DTR signal will be ignored
Note: This is the function of this register when &M1 is not set.

INACTIVITY TIMER
Type:	Register
Format	AT [cmds] S30=n [cmds]
Default:	0
Range:	0-255
Unit:	.1 sec
Description:	Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process.
Note:	S30=0 disables the timer and allows indefinite inactivity.

INACTIVITY TIMER
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Default:	0
Range:	0-42
Unit:	1 minute
Description:	Sets the length of time that the modem does not receive information before it disconnects.

NO CARRIER TIME-OUT
Type:	Register
Format	AT [cmds] S7=n [cmds]
Default:	50
Range:	1-255
Unit:	1 second
Description:	Maximum wait time the modem uses after dialing to detect a carrier signal from the remote modem for both originating and answering calls.
Note:	W dial modifier also uses S7 to set the maximum time to wait.

PULSE DIALING RATIO
Type:	Configuration
Format:	AT [cmds] &Pn [cmds]
Description:	Selects pulse dial make/break ratio
Command	Function
í &P0	39/61ms at 10pps (North America)
&P1	33/67ms at 10pps (Europe)
&P2	33/67ms at 20pps

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports ROM checksum
I2	Tests and reports ROM checksum
I3	Reports revision level of firmware
I4	Reports the capabilities of the product

RESULT CODES
Type:	Configuration
Format:	AT [cmds] Qn [cmds]
Description:	Enables modem to send result codes to the DTE
Command	Function
í Q0	Result code sending enabled
Q1	Result code sending disabled
Q2	Result code sending enabled only if originating call

v.42bis Compression type
Type:	Configuration
Format:	AT [cmds] %Mn [cmds]
Description:	Sets type of compression used in V.42bis mode
Command		Function
%M0		Compression disabled
%M1		Transmit compression enabled
%M2		Receive compression enabled
í %M3		Bi-directional compression enabled

v.42bis dictionary reset
Type:	Immediate
Format:	AT [cmds] %P [cmds]
Description:	Resets local and remote V.42bis Dictionaries

V.42bis dictionary size
Type:	Configuration
Format:	AT [cmds] %Dn [cmds]
Description:	Sets the size of the dictionary used in V.42bis mode
Command		Function
%D0		512
%D1		1024
í %D2		2048
%D3		4096

V.42bis Maximum string length
Type:	Configuration
Format:	AT [cmds] %Sn [cmds]
Default:	32
Range:	6-250
Unit:	Characters
Description:	Sets the Maximum number of characters that can be compressed into a word under V.42bis compression