CONNECTIONS
Purpose	Location	Purpose	Location
Switched line	CN1	Power switch	SW1
Leased line	CN2	Scroll left	CN6
RS-232/422	CN3	Scroll right	CN7
DC power	CN4	Go up one level	CN8
Network Management (proprietary)	CN5	Go to top level	CN9

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
PWR	Green	On	Power is on
PWR	Green	Off	Power is off
ALRM	Red	Blinking	Major alarm detected in a remote 392x series modem
ALRM	Red	Off	Normal operation
DIAG	Green	On	Modem is receiving diagnostic messages
DIAG	Green	Off	Modem is not receiving diagnostic messages
DTR/108	Green	On	DTR signal is high
DTR/108	Green	Off	DTR signal is low
RTS/105	Green	On	RTS signal is high
RTS/105	Green	Off	RTS signal is low
CTS/106	Green	On	CTS signal is high
CTS/106	Green	Off	CTS signal is low
TXD/103	Green	On	Modem is receiving data from DTE
TXD/103	Green	Off	Modem is not receiving data from DTE
LSD/109	Green	On	Carrier signal detected
LSD/109	Green	Off	Carrier signal not detected
RXD/104	Green	On	Modem is transmitting data to DTE
RXD/104	Green	Off	Modem is not transmitting data to DTE
SQ	Yellow	Blinking	Line signal is degraded or data path is being blocked
SQ	Yellow	Off	Normal operation
TEST/142	Yellow	On	Test connection established
TEST/142	Yellow	Blinking	Modem is upgrading firmware
TEST/142	Yellow	Off	No test connection established
RATE	Yellow	On	Modem is connected at less than configured speed
RATE	Yellow	Off	Modem is connected at configured speed
DIAL	Yellow	On	Modem is establishing a switched line connection
DIAL	Yellow	Blinking	Switched line connection established
DIAL	Yellow	Off	No switched line connection

ANTISTREAMING
Type:	Register
Format:	AT [cmds] S72=n [cmds]
Example:	AT S72=0 &W<CR>
Description:	Selects antistreaming option
í Command	Function
í 72=0	Disabled
í S72=1	10 seconds
í S72=2	30 seconds
í S72=3	1 minute
í S72=4	2 minutes
í S72=5	3 minutes
í S72=6	5 minutes

AT COMMAND RESPONSE
Type:	Register
Format:	AT [cmds] S84=n [cmds]
Example:	AT S84=0 &W<CR>
Description:	Sets the response to AT commands.
í Command	Function
í S84=0	Normal operation
í S84=1	Execute valid commands, suppress error codes.
í S84=2	Ignore configuration commands, always return OK error code.

AUTO BAUD
Type:	Register
Format:	AT [cmds] S78=n [cmds]
Example:	AT S78=0 &W<CR>
Description:	Allows modem to connect at remote modem’s modulation.
í Command	Function
í S78=0	Auto baud enabled.
í S78=1	Auto baud disabled.

AUTO-RELIABLE FALLBACK CHARACTER
Type:	Configuration
Format:	AT [cmds] %An [cmds]
Example:	AT%A20<CR>
Default:	15
Range:	0-127
Unit:	ASCII
Description:	Sets the character used as the auto-reliable fallback character. %A0 will disable this function.

AUTO-RELIABLE TIME BUFFER CONFIGURATION
Type:	Configuration
Format:	AT [cmds] \Cn [cmds]
Example:	AT \C1 &W<CR>
Description:	Controls the handling of incoming data during auto-reliable time period.
í Command	Function
í \CO	Data is discarded.
í \C1	Data is buffered.
í \C2	Data is discarded, resets to \C1 on receipt of autoreliable fallback character.

BREAK TYPE
Type:	Configuration
Format:	AT [cmds] \Kn [cmds]
Example:	AT \K5 &W<CR>
Description:	Selects response to DTE break command.
í Command	Function
í \K0	Send break, clear buffer, enter command mode.
í \K1	Send break, clear buffer
í \K2	Send break, send data, enter command mode.
í \K3	Send break. send data,
í \K4	Send data, send break, enter command mode.
í \K5