POWERCOM AMERICA, INC.
PM3314E
|
Card Type |
Modem (asynchronous/synchronous) |
|
Chipset |
Unidentified |
|
Maximum Data Rate |
33.6Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 |
|
Fax Modulation |
Unidentified |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Unidentified |
|
Data Bus |
Serial |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
Telephone line in |
CN1 |
DC power in |
CN4 |
|
Telephone line out |
CN2 |
Power switch |
SW1 |
|
Serial port |
CN3 | ||
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
í AT command set enabled |
JP1 |
Open |
|
AT command set disabled |
JP1 |
Closed |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
TST |
Unidentified |
Blinking |
Data error detected |
|
TST |
Unidentified |
Off |
Data error not detected |
|
AA |
Unidentified |
On |
Auto-answer enabled |
|
AA |
Unidentified |
Off |
Auto-answer disabled |
|
AA |
Unidentified |
Blinking |
Phone is ringing |
|
CD |
Unidentified |
On |
Carrier signal detected |
|
CD |
Unidentified |
Off |
Carrier signal not detected |
|
CD |
Unidentified |
Blinking |
Modem is retraining |
|
OH |
Unidentified |
On |
Modem is off-hook |
|
OH |
Unidentified |
Off |
Modem is on-hook |
|
RD |
Unidentified |
On |
Modem is receiving data |
|
RD |
Unidentified |
Off |
Modem is not receiving data |
|
SD |
Unidentified |
On |
Modem is transmitting data |
|
SD |
Unidentified |
Off |
Modem is not transmitting data |
|
TR |
Unidentified |
On |
DTR signal is high |
|
TR |
Unidentified |
Off |
DTR signal is low |
|
MR |
Unidentified |
On |
Power is on |
|
MR |
Unidentified |
Off |
Power is off |
|
MR |
Unidentified |
Blinking |
Modem is performing self-test |
|
H Color |
M Color |
L Color |
Condition |
|
Off |
Off |
Off |
Modem is connected at 300bps |
|
Off |
Off |
Red |
Modem is connected at 1200bps |
|
Off |
Red |
Off |
Modem is connected at 2400bps |
|
Off |
Red |
Red |
Modem is connected at 4800bps |
|
Red |
Off |
Off |
Modem is connected at 7200bps |
|
Red |
Off |
Red |
Modem is connected at 9600bps |
|
Red |
Red |
Off |
Modem is connected at 12Kbps |
|
Red |
Red |
Red |
Modem is connected at 14.4Kbps |
|
Off |
Green |
Off |
Modem is connected at 16.8Kbps |
|
Off |
Green |
Green |
Modem is connected at 19.2Kbps |
|
Green |
Off |
Off |
Modem is connected at 21.6Kbps |
|
Green |
Off |
Green |
Modem is connected at 24Kbps |
|
Green |
Green |
Off |
Modem is connected at 26.4Kbps |
|
Green |
Green |
Green |
Modem is connected at 28.8Kbps |
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, ‘comma’, A/ |
|
A, B, D, E, H, L, M, O, Q, V, W, X, Y, Z |
|
&C, &D, &F, &G, &K, &L, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \C, \J, \N, \Q, \T, \V, \X |
|
%A, %C |
|
S-Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S22, S25, S26, S36, S38, S48 |
|
S82, S95 |
Note: See MHI help file for complete information. The standard S36, S38, and S48 commands listed above are only valid for V.42/V.42bis mode. For the MNP versions of these registers, please see the Proprietary AT Command Set section. |
|
UNIDENTIFIED COMMANDS | |
|
Command |
Default |
|
%P |
0 |
Proprietary AT Command Set
|
AUTO-RELIABLE FALLBACK CHARACTER | |
|
Type: |
Register |
|
Format: |
AT [cmds] S37=n [cmds] |
|
Default: |
Unidentified |
|
Range: |
0 - 127 |
|
Unit: |
1 ASCII character |
|
Description: |
Sets the character used as the auto-reliable fallback character; setting S37 to 0 will disable this function. |
|
Note: |
This register is only valid for MNP mode. |
|
BIT-MAPPED REGISTER S14 | ||
|
Format: |
AT [cmds] S14=n [cmds] | |
|
Default: |
N/A | |
|
Range: |
0 - 255 | |
|
Description: |
Reports setting of JP1, and controls echo, result codes and display, dial mode, and answer/originate mode. | |
|
Note: |
Bit 4 is read-only. | |
|
Bit |
Value |
Function |
|
0 |
í 01 |
V.42 result codes disabled. V.42 result codes enabled. |
|
1 |
0 í 1 |
Command echo disabled. Command echo enabled. |
|
2 |
í 01 |
Result codes enabled. Result codes disabled. |
|
3 |
0 í 1 |
Display result codes in numeric format. Display result codes in verbose format. |
|
4 |
0 1 |
Jumper JP1 is open. Jumper JP1 is closed. |
|
5 |
í 01 |
Tone dial enabled. Pulse dial enabled. |
|
6 |
í 01 |
Modem defaults to profile 0 on power-up. Modem defaults to profile 1 on power-up. |
|
7 |
0 í 1 |
Answer mode enabled. Originate mode enabled. |
|
BIT-MAPPED REGISTER S21 | ||
|
Format |
AT [cmds] S21=n [cmds] | |
|
Default: |
48 | |
|
Range: |
0 - 254 | |
|
Description: |
Selects line type, CTS/DCD/DSR signals, low DTR action, and the long space disconnect function. | |
|
Bit |
Value |
Function |
|
0 |
0 |
Not used. |
|
1 |
í 01 |
Modem is connected to switched line. Modem is connected to leased line. |
|
2 |
í 01 |
CTS follows RTS. CTS forced high. |
|
4, 3 |
00 01 í 1011 |
DTR signal ignored. Modem goes to command mode on low DTR. Modem disconnects on low DTR; Auto-Answer is disabled. Modem is initialized on low DTR. |
|
5 |
0 í 1 |
DCD forced high. DCD normal. |
|
6 |
í 01 |
DSR forced high. DSR normal. |
|
7 |
í 01 |
Long space disconnect function disabled. Long space disconnect function enabled. |
|
BIT-MAPPED REGISTER S23 | ||
|
Format |
AT [cmds] S23=n [cmds] | |
|
Default: |
Unidentified | |
|
Range: |
0 - 60 | |
|
Description: |
Controls DTE rate and parity. | |
|
Bit |
Value |
Function |
|
3 - 0 |
0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 |
Sets serial port speed to 110bps. Sets serial port speed to 300bps. Sets serial port speed to 600bps. Sets serial port speed to 1200bps. Sets serial port speed to 2400bps. Sets serial port speed to 4800bps. Sets serial port speed to 9600bps. Sets serial port speed to 14.4Kbps. Sets serial port speed to 19.2Kbps. Sets serial port speed to 38.4Kbps. Sets serial port speed to 57.6Kbps. Sets serial port speed to 76.8Kbps. Sets serial port speed to 115.2Kbps. |
|
5, 4 |
00 01 10 11 |
Use even parity. Use SPACE parity. Use odd parity. Use MARK or no parity. |
|
BIT-MAPPED REGISTER S27 | ||
|
Format |
AT [cmds] S27=n [cmds] | |
|
Default: |
Unidentified | |
|
Range: |
0 - 111 | |
|
Description: |
Selects synchronous/asynchronous mode, line type, clock source, and ITU-T/Bell modes. | |
|
Bit |
Value |
Function |
|
2 - 0 |
000 001 010 011 101 |
Asynchronous mode, serial port speed follows connect speed. Asynchronous off-line command mode and synchronous connect mode. Synchronous command and connect mode. Synchronous connect mode, command mode disabled. Error correction mode. |
|
3 |
0 |
Not used. |
|
5, 4 |
00 01 10 |
Local modem generates transmit clock source. Local DTE generates transmit clock source. Remote DCE/DTE generates transmit clock source. |
|
7, 6 |
00 01 10 |
Modem will use ITU-T V.22 at 1200bps. Modem will use Bell 212A at 1200bps. Modem will use ITU-T V.23 at 1200bps. |
|
BIT-MAPPED REGISTER S28 | |||||
|
Format: |
AT [cmds] S28=n [cmds] | ||||
|
Default: |
Unidentified | ||||
|
Range: |
0 - 27 | ||||
|
Description: |
Controls line speed and the unidentified function set by the %P command. | ||||
|
Bit |
Value |
Function | |||
|
0 |
0 1 |
Set %P0. Set %P1. | |||
|
4 - 1 |
0000 0001 0010 0011 0100 0101 0110 0111 1000 1001 1010 1011 1100 1101 |
Connect at 300bps. Connect at 1200bps. Connect at 2400bps. Connect at 4800bps. Connect at 7200bps. Connect at 9600bps. Connect at 12Kbps. Connect at 14.4Kbps. Connect at 16.8Kbps. Connect at 19.2Kbps. Connect at 21.6Kbps. Connect at 24Kbps. Connect at 26.4Kbps. Connect at 28.8Kbps. | |||
|
BIT-MAPPED REGISTER S36 | |||||
|
Format: |
AT [cmds] S36=n [cmds] | ||||
|
Default: |
137 | ||||
|
Range: |
0 - 203 | ||||
|
Description: |
Controls connect mode, XON/XOFF pass-through, and flow control type. | ||||
|
Note: |
This register is only valid for MNP mode. | ||||
|
Bit |
Value |
Function | |||
|
1, 0 |
00 í 0110 11 |
Normal mode enabled. Direct mode enabled. MNP reliable mode enabled. Auto-reliable mode enabled. | |||
|
2 |
0 |
Not used. | |||
|
3 |
0 í 1 |
XON/XOFF signals trapped by local modem. XON/XOFF passed through local modem. | |||
|
5 - 4 |
00 |
Not used. | |||
|
7, 6 |
00 01 í 1011 |
Flow control disabled. Bidirectional XON/XOFF flow control enabled. CTS flow control by DCE enabled. Bidirectional RTS/CTS flow control enabled. | |||
|
BIT-MAPPED REGISTER S38 | |||||
|
Format: |
AT [cmds] S38=n [cmds] | ||||
|
Default: |
4 | ||||
|
Range: |
0 - 22 | ||||
|
Description: |
Controls the auto-reliable time buffer, serial port speed buffering, and error correction and compression result codes. | ||||
|
Note: |
This register is only valid for MNP mode. | ||||
|
Bit |
Value |
Function | |||
|
1, 0 |
í 0001 10 |
Incoming data during the auto-reliable time is discarded. Incoming data during the auto-reliable time is buffered for 4 seconds or 200 characters. Incoming data during the auto-reliable time is discarded; modem returns to normal mode on receiving auto-reliable fallback character. | |||
|
2 |
0 í 1 |
Serial port speed locked. Serial port speed follows connect speed. | |||
|
3 |
0 |
Not used. | |||
|
4 |
í 01 |
Error correction and compression extended result codes disabled. Error correction extended result codes enabled. | |||
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Selects the communication protocol for low-speed data calls. |
|
Command |
Protocol |
|
í B0 |
Modem will use ITU-T V.22 at 1200bps. |
|
B1 |
Modem will use Bell 212A at 1200bps. |
|
B2 |
Modem will use ITU-T V.23 at 1200bps. |
|
COMPRESSION | |
|
Type: |
Register |
|
Format: |
AT [cmds] S41=n [cmds] |
|
Description: |
Selects data compression. |
|
Note: |
This register is only valid for MNP mode. |
|
Command |
Function |
|
í S41=0 |
Data compression disabled. |
|
S41=1 |
Data compression enabled. |
|
DISPLAY INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested about the modem. |
|
Command |
Function |
|
I0 |
Displays product identification code. |
|
I1 |
Displays ROM checksum. |
|
I2 |
Tests and displays ROM checksum result. |
|
I6 |
Displays firmware revision. |
|
INACTIVITY TIMER | |
|
Type: |
Register |
|
Format: |
AT [cmds] S39=n [cmds] |
|
Default: |
0 |
|
Range: |
Unidentified |
|
Unit: |
Unidentified |
|
Description: |
Sets the length of time that the modem does not receive information before it disconnects. |
|
Note: |
This register is only valid for MNP mode. |
|
LINE SPEED | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Nn [cmds] |
|
Description: |
Selects the speed the modem will attempt to connect at. |
|
Command |
Function |
|
&N0 |
Attempt to connect at speed of last AT command. |
|
&N1 |
Connect at 300bps. |
|
&N2 |
Connect at 1200bps. |
|
&N3 |
Connect at 2400bps. |
|
&N4 |
Connect at 4800bps. |
|
&N5 |
Connect at 7200bps. |
|
&N6 |
Connect at 9600bps. |
|
&N7 |
Connect at 12Kbps. |
|
&N8 |
Connect at 14.4Kbps. |
|
&N9 |
Connect at 16.8Kbps. |
|
&N10 |
Connect at 19.2Kbps. |
|
&N11 |
Connect at 21.6Kbps. |
|
&N12 |
Connect at 24Kbps. |
|
&N13 |
Connect at 26.4Kbps. |
|
&N14 |
Connect at 28.8Kbps. |
|
MAXIMUM BLOCK SIZE FOR TRANSMISSION | |
|
Type: |
Register |
|
Format: |
AT [cmds] S40=n [cmds] |
|
Description: |
Sets the maximum transmittable block size in MNP mode. |
|
Note: |
This register is only valid for MNP mode. |
|
Command |
Function |
|
S40=0 |
Maximum MNP block size is 64 characters. |
|
S40=1 |
Maximum MNP block size is 128 characters. |
|
S40=2 |
Maximum MNP block size is 192 characters. |
|
í S40=3 |
Maximum MNP block size is 256 characters. |
