Card Type	Fax, Modem (asynchronous)
Chip Set	Unidentified
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	8-bit ISA
Fax Class	Class I & II
Data Modulation Protocol	Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42bis

CONNECTIONS
Function	Label		Function		Label
Line out		CN1		Line in		CN2

SERIAL PORT ADDRESS
Setting	SW1/A	SW1/B
COM1 (3F8h)	On	On
í COM2 (2F8h)	On	Off
COM3 (3E8h)	Off	On
COM4 (2E8h)	Off	Off

INTERRUPT
Setting	JP1/A	JP1/B	JP1/C
2	Open	Closed	Open
í 3	Closed	Open	Open
4	Closed	Open	Open
5	Open	Open	Closed

SLEEP TIMER
Type:	Register
Format	AT [cmds] S24=n [cmds]
Default:	0
Range:	0-255
Unit:	1 second
Description:	Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode.
Note:	ATS24=0 will disable timer

INACTIVITY TIMER
Type:	Register
Format	AT [cmds] S30=n [cmds]
Default:	0
Range:	0-255
Unit:	10 seconds
Description:	Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process.
Note:	ATS30=0 will disable timer

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Modifier	Function
L	Re-dial last number
P	Pulse dialing enabled
R	Answer mode enabled, originate mode disabled following handshake initiation
S=n	Dial stored telephone number n
T	Tone dialing enabled
W	Dialing resumed following dial tone detection
,	Dialing paused for amount of time specified in S8 register
"	Letters enclosed in quotes are interpreted as numbers according to the telephone keypad
!	Modem commanded to go off-hook for specified time before returning on-hook
@	Wait for quiet answer
$	Waits for prompt tone for amount of time specified by the S7 register
;	Modem returned to command state after dialing

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I0	Reports product code
I1	Reports ROM checksum
I2	Tests and reports ROM checksum
I3	Reports firmware revision
I4	Returns numbers in bit-map format on software capabilities of the modem
I6	Reports data connection information

HELP SCREENS
Type:	Immediate
Format:	AT [cmds] $H [cmds]
Description:	Display help screens. To page forward use <space bar>, and to exit use <ESC>

COMPRESSION
Type:	Configuration
Format:	AT [cmds] %Cn [cmds]
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
%C1	MNP5 enabled
%C2	V.42bis enabled
í %C3	MNP5 and V.42bis enabled

CLOCK DOUBLER
Type:	Configuration
Format:	AT [cmds] %BAUDn [cmds]
Description:	Controls clock doubler at the UART
Command		Function
%BAUD?		Reports current clock doubler setting
%BAUD=?		Reports available clock doubler modes
%BAUD0		Standard UART speed / clock doubler disabled
%BAUD1		Double specified UART speed clock doubler enabled

CALLER ID
Type:	Configuration
Format:	AT [cmds] %CCID=n [cmds]
Description:	Controls the Caller ID function
Command	Function
%CCID=0	Caller ID disabled
%CCID=1	Caller ID displays formatted data
%CCID=2	Caller ID displays raw hexadecimal data

DUMB MODE
Type:	Configuration
Format:	AT [cmds] %DUMBn [cmds]
Description:	Controls command recognition and result codes, dumb mode
Command		Function
í %DUMB0		Dumb mode disabled
%DUMB1		Dumb mode enabled

AUTO-RETRAIN - AUTO-FALLBACK/FALL-FORWARD
Type:	Configuration
Format:	AT [cmds] %En [cmds]
Description:	Controls auto-retrain mode and fallback/fall-forward
Command	Function
í %E0	Auto-retrain disabled
%E1	Auto-retrain enabled
%E2	Auto-fallback/fall-forward enabled

LINE SIGNAL LEVEL
Type:	Immediate
Format:	AT [cmds] %L [cmds]
Description:	Returns a value which indicates the received line signal level

LINE SIGNAL QUALITY
Type:	Immediate
Format:	AT [cmds] %Q [cmds]
Description:	Returns a value which indicates line signal quality (-dBm)

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
í \A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
\A3	MNP block size is 256 characters

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem

AUTO-RELIABLE TIME BUFFER CONFIGURATION
Type:	Configuration
Format:	AT [cmds] \Cn [cmds]
Description:	Controls the handling of incoming data during auto-reliable time period
Command	Function
í \C0	Data is discarded
\C1	Data is buffered
\C2	Data is discarded; modem returns to normal mode on receiving auto-reliable fallback character.

ECHO DATA
Type:	Configuration
Format:	AT [cmds] \En [cmds]
Description:	Enables modem to echo received data
Command	Function
\E0	Data echo disabled
í \E1	Data echo enabled

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
í \G0	Flow control disabled
\G1	Flow control enabled

LOCK SERIAL PORT
Type:	Configuration
Format:	AT [cmds] \Jn [cmds]
Description:	Sets operation of serial port speed
Command	Function
í \J0	Serial speed locked
\J1	Serial speed follows connect speed

BREAK TYPE
Type:		Configuration
Format:		AT [cmds] \Kn [cmds]
Description:		Configures action of break signal
Command	Break from DTE		Modem receives \B	Break received from remote modem
\K0	Online command mode enabled, send no break to remote modem		Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
\K1	Break sent to remote modem and buffered cleared		Break sent to remote modem and buffered cleared	Buffers cleared, break sent to DTE
\K2	Online command mode enabled, send no break to remote modem		Send break to remote modem immediately	Break sent immediately to DTE
\K3	Send break to remote modem immediately		Send break to remote modem immediately	Break sent immediately to DTE
\K4	Online command mode enabled, send no break to remote modem		Send break with transmitted data	Break sent with received data to the DTE
í \K5	Send break with transmitted data		Send break with transmitted data	Break sent with received data to the DTE

MNP - STREAM/BLOCK MODE
Type:	Configuration
Format:	AT [cmds] \Ln [cmds]
Description:	Selects the transfer mode for MNP link
Command	Function
í \L0	Stream mode for MNP enabled
\L1	Block mode for MNP enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Controls the type of connection the modem will operate in
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	Reliable mode enabled
\N3	Auto-reliable mode enabled
\N4	V.42 reliable mode enabled
\N5	MNP reliable mode enabled

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
í \Q0	Flow control disabled
\Q1	XON/XOFF flow control enabled
\Q2	CTS flow control by DCE enabled
\Q3	RTS/CTS flow control enabled

CURRENT CONFIGURATION
Type:	Immediate
Format:	AT [cmds] \S [cmds]
Description:	Displays current operating parameters

INACTIVITY TIMER
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Default:	0
Range:	0-90
Unit:	1 minute
Description:	Sets the length of time that the modem does not receive information before it disconnects.
Note:	AT\T0 will disable timer

EXTENDED RESULT CODES - MNP
Type:	Configuration
Format:	AT [cmds] \Vn [cmds]
Description:	Selects extended result codes (MNP)
Command	Function
\V0	Extended result codes disabled
í \V1	Extended result codes enabled

XON/XOFF PASS-THROUGH
Type:	Configuration
Format:	AT [cmds] \Xn [cmds]
Description:	Selects whether XON/XOFF signals are sent to remote modem
Command	Function
í \X0	XON/XOFF signals trapped by local modem
\X1	XON/XOFF passed through local modem