Card Type	ISDN TA
Chip Set	Unidentified
Maximum Modem Rate	56Kbps
Maximum Fax Rate	14.4Kbps
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32bis, V.34, K56flex
ISDN Data Rate	128Kbps
ISDN Modulation Protocol	V.110, V.120, X.75, ML-PPP, PPP
Error Correction/Compression	Unidentified
Data Bus	PCMCIA

SUPPORTED COMMAND SET

Basic AT Commands

AT, ‘+++’

A, E

&F, &V, &Z

Note: See MHI Help File for full command documentation.

CONVERSION LINK
Type:	Configuration
Format:	AT [cmds] &N0=n [cmds]
Description:	Loads user profiles into active RAM
Command	Function
&N0=0	Set single-link mode for async to sync PPP conversion
&N0=1	Set multi-link mode for async to sync PPP conversion

DIAL
Type:	Immediate
Format:	AT [cmds] D<#> [cmds]
Description:	Dials ISDN telephone number according to any modifiers included in the string
Note:	Any combination of modifiers can be used to produce the desired dial functions in sequence.
Command	Function
DSn	Dial stored telephone number n
DM	Modem calls over ISDN line
DT	Dials out the ISDN number
DV	ISDN voice calls enabled
DL	Re-dial last ISDN number

HOOK CONTROL
Type:	Immediate
Format:	AT [cmds] Hn [cmds]
Description:	Selects ISDN disconnect
Command	Function
H0	Modem commanded to go on-hook (hang-up)
H1	Modem commanded to disconnect ISDN voice calls
H3	Modem commanded to disconnect ISDN data & voice calls
H4	Restarts ISDN layer 2 link
H5	View responses

ISDN/ANALOG
Type:	Configuration
Format:	AT [cmds] &Gn [cmds]
Description:	Toggles between ISDN and analog phone link
Command	Function
&G0	Switch from ISDN link to analog line
&G1	Switch from analog to ISDN link

LOAD USER PROFILE
Type:	Configuration
Format:	AT [cmds] &Ln [cmds]
Description:	Loads user profiles into active RAM
Command	Function
&L0	Load user profile 0 into active RAM
&L1	Load user profile 1 into active RAM
&L2	Load user profile 2 into active RAM
&L3	Load user profile 3 into active RAM
&L4	Load user profile 4 into active RAM
&L5	Load user profile 5 into active RAM
&L6	Load user profile 6 into active RAM
&L7	Load user profile 7 into active RAM
&L8	Load user profile 8 into active RAM
&L9	Load user profile 9 into active RAM

ON-LINE
Type:	Immediate
Format:	AT [cmds] On [cmds]
Description:	Controls on-line command (data transmission) state options.
Note: The O command must be placed at the end of the command string.
Command	Function
O0	On-line command mode with no retraining enabled

PHONE NUMBERS IN MULTI-LINK PPP
Type:	Configuration
Format:	AT [cmds] &Jn [cmds]
Description:	Selects 1 or 2 ISDN phone numbers for Multi-Link PPP calls
Command	Function
&J0	2 ISDN phone numbers selected for multi-link PPP calls
&J1	1 ISDN phone number selected for multi-link PPP calls

REPORT INFORMATION
Type:	Immediate
Format:	AT [cmds] In [cmds]
Description:	Displays information requested
Command	Function
I3	OK

RESTORE PROFILE ON POWER-UP
Type:	Configuration
Format:	AT [cmds] &Pn [cmds]
Description:	Restores a selected profile into the active profile on power-up (hard reset)
Command	Function
&P0	Restore profile 0 on power-up
&P1	Restore profile 1 on power-up
&P2	Restore profile 2 on power-up
&P3	Restore profile 3 on power-up
&P4	Restore profile 4 on power-up
&P5	Restore profile 5 on power-up
&P6	Restore profile 6 on power-up
&P7	Restore profile 7 on power-up
&P8	Restore profile 8 on power-up

STORE ACTIVE PROFILE
Type:	Configuration
Format:	AT [cmds] &Wn [cmds]
Description:	Writes the values for the active profile into the non-volatile RAM
Command	Function
&W0	Write the active profile to stored profile 0
&W1	Write the active profile to stored profile 1
&W2	Write the active profile to stored profile 2
&W3	Write the active profile to stored profile 3
&W4	Write the active profile to stored profile 4
&W5	Write the active profile to stored profile 5
&W6	Write the active profile to stored profile 6
&W7	Write the active profile to stored profile 7
&W8	Write the active profile to stored profile 8
&W9	Write the active profile to stored profile 9

V.110 DATA RATE
Type:	Configuration
Format:	AT [cmds] Bn [cmds]
Description:	Selects the user rate in V.110 mode
Command	Protocol
B0	600bps
B1	1200bps
B2	2400bps
B3	4800bps
B4	9600bps
B5	19.2Kbps
B6	38.4Kbps
B7	48.0Kbps
B8	57.6Kbps (Japan only)

VERIFY HARDWARE
Type:	Immidiate
Format:	AT [cmds] &Kn [cmds]
Description:	Verifies TA hardware
Command	Function
&K0	Verifies TA hardware. Reports OK or BAD

B-CHANNEL SPEED
Type:	Configuration
Format:	AT [cmds] !Q=n [cmds]
Description:	Selects B-channel speed
Command	Function
!Q=0	B-channel set to 64Kbps
!Q=4	B-channel set to 56Kbps

DATA DIRECTORY NUMBER
Type:	Configuration
Format:	AT [cmds] !N1=n [cmds]
Range:	0 - 24
Unit:	0 - 9, *, #
Description:	Sets the directory number (DN) 1 for the data channel

DATA DIRECTORY NUMBER
Type:	Configuration
Format:	AT [cmds] !N0=n [cmds]
Range:	0 - 24
Unit:	0 - 9, *, #
Description:	Sets the directory number (DN) 0 for the data channel

DATA SPID
Type:	Configuration
Format:	AT [cmds] !C6=n [cmds]
Range:	0 - 20
Unit:	ASCII
Description:	Specifies the data service profile identifier 0 assigned by the ISDN provider

DATA SPID
Type:	Configuration
Format:	AT [cmds] !C2=n [cmds]
Range:	0 - 20
Unit:	ASCII
Description:	Specifies the data service profile identifier 1 assigned by the ISDN provider

ISDN D-CHANNEL PROTOCOL
Type:	Configuration
Format:	AT [cmds] !C0=n [cmds]
Description:	Selects network switch type
Command	Function
!C0=0	AT&T 5ESS
!C0=1	Northern Telecom DMS-100
í !C0=2	Euro-ISDN NET3
!C0=5	VN4

RATE ADAPTION PROTOCOL
Type:	Configuration
Format:	AT [cmds] !Z=n [cmds]
Description:	Select rate adaption protocol used to communicate with another TA
Command	Function
!Z=5	V.120
!Z=6	V.110

VOICE-GRADE CALL HANDLING
Type:	Configuration
Format:	AT [cmds] !V=n [cmds]
Description:	Controls voice grade call handling
Command	Function
!V=0	Incoming voice grade calls are answered by ISDN phone
!V=1	Incoming voice grade calls are answered by modem
!V=2	Audio speech enabled
!V=4	m -law encoding enabled (Europe)
!V=5	A -law encoding enabled (North America)