MOTOROLA, INC.
PREMIER 33.6 INTERNAL
|
Card Type |
Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Modem Rate |
33.6Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.42, V.32bis, V.32, V.22bis, V.21 |
|
Fax Modulation Protocol |
ITU-T V.21CH2, V.27ter, V.29, V.17 |
|
Error Correction/Compression |
MNP5, V.42/V.42bis |
|
Fax Class |
Class I & II |
|
Data Bus |
8-bit ISA |
|
Card Size |
Half-length, full-height card |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line in |
CN1 |
Line out |
CN2 | |||
|
PLUG & PLAY | ||||
|
Setting |
SW2/1 |
SW2/2 |
SW2/3 |
SW2/4 |
|
í Manual |
On |
On |
Off |
Off |
|
Plug and Play |
Off |
Off |
On |
On |
|
COM PORT SELECTION | ||
|
Setting |
SW1/1 |
SW1/2 |
|
COM1 |
On |
On |
|
COM2 |
On |
Off |
|
í COM3 |
Off |
On |
|
COM4 |
Off |
Off |
|
INTERRUPT | ||||
|
Setting |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
|
IRQ2 |
On |
Off |
Off |
Off |
|
IRQ3 |
Off |
On |
Off |
Off |
|
IRQ4 |
Off |
Off |
On |
Off |
|
í IRQ5 |
Off |
Off |
Off |
On |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
AA |
Unidentified |
On |
Auto-answer enabled |
|
AA |
Unidentified |
Off |
Auto-answer disabled |
|
AA |
Unidentified |
Blinking |
Phone is ringing |
|
RD |
Unidentified |
On |
Computer is receiving data from the modem |
|
RD |
Unidentified |
Off |
Computer is not receiving data from the modem |
|
SD |
Unidentified |
On |
Computer is transmitting data to the modem |
|
SD |
Unidentified |
Off |
Computer is not transmitting data to the modem |
|
CD |
Unidentified |
On |
Carrier signal detected |
|
CD |
Unidentified |
Off |
Carrier signal not detected |
|
OH |
Unidentified |
On |
Modem is off-hook |
|
OH |
Unidentified |
Off |
Modem is on-hook |
|
HS |
Unidentified |
On |
Modem is operating at 16800, 19200, 21600, 28800, or 33600bps |
|
HS |
Unidentified |
Off |
Modem is operating at 4800, 7200, 9600, 12000, 14400bps |
|
TR |
Unidentified |
On |
DTR signal is high |
|
TR |
Unidentified |
Off |
DTR signal is low |
|
MR |
Unidentified |
On |
Power is on |
|
MR |
Unidentified |
Off |
Power is off |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, ‘+++’, A/ |
|
A, E, O, S, V, X, Y, Z |
|
&G, &L, &T, &W, &X, &Y, &Z |
|
Extended AT Commands |
|
\A, \G, \X |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S18, S25, S26 |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DP |
Pulse dialing enabled |
|
DR |
Answer mode enabled; originate mode disabled following handshake initiation. |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
HOOK CONTROL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Hn [cmds] |
|
Description: |
Selects whether the modem is on-hook or off-hook |
|
Command |
Function |
|
í H0 |
Modem commanded to go on-hook (hang-up) |
|
H1 |
Modem commanded to go off-hook (pick-up) |
|
H2 |
Set H command to allow cleardown |
|
H3 |
Set H command to disallow cleardown |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product code |
|
I1 |
Reports EPROM CRC value |
|
I3 |
Reports product version |
|
I4 |
Reports capability code |
|
I5 |
Reports disconnect reason |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
í L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
|
SPEAKER MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Mn [cmds] |
|
Description: |
Selects various speaker options |
|
Command |
Function |
|
M0 |
Speaker disabled |
|
í M1 |
Speaker enabled until carrier signal detected |
|
M3 |
Speaker enabled following dialing, then disabled after carrier signal detected. |
|
RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Qn [cmds] |
|
Description: |
Enables modem to send result codes to the DTE |
|
Command |
Function |
|
í Q0 |
Result code sending enabled |
|
Q1 |
Result code sending disabled |
|
Q2 |
Result code sending in originate mode only |
|
DATA CARRIER DETECT (DCD) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Cn [cmds] |
|
Description: |
Selects whether the DCD option is enabled or disabled |
|
Command |
Function |
|
í &C0 |
DCD enabled |
|
&C1 |
DCD enabled after carrier signal detected |
|
&C2 |
DCD off 5 seconds after disconnect |
|
&C3 |
DCD follows remote RTS |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
Note: The action each variant of &D causes depends on the setting of &Q | |
|
Command |
Function |
|
í &D0 |
Modem does not respond to DTR |
|
&D1 |
Modem goes to command mode after DTR goes is off |
|
&D2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. |
|
&D3 |
Modem is initialized after DTR goes off |
|
&D9 |
DTR dials/disconnects |
|
FACTORY DEFAULT PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &F [cmds] |
|
Description: |
Sets values in active profile to values found in the default profile |
|
Command |
Function |
|
í &F0 |
Restore factory default 0 |
|
&F1 |
Restore factory default 1 |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Mn [cmds] |
|
Description: |
Selects communications mode |
|
Command |
Mode |
|
í &M0 |
Asynchronous dial/asynchronous data |
|
&M1 |
Asynchronous dial/synchronous data |
|
&M2 |
Dial stored number when DTR off/on transition is detected/sync data |
|
&M3 |
Manual dial/sync data |
|
&M4 |
V.25bis dialer/BISYNC protocol/sync data (EBCDIC) |
|
&M5 |
V.25bis dialer/SDLC protocol/sync data (NRZ) |
|
&M6 |
V.25bis async dial/sync data |
|
&M7 |
V.25bis async dial/async data |
|
&M8 |
V.25bis dialer w/BISYNC protocol/sync data (EBCDIC) |
|
&M9 |
V.25bis dialer w/SDLC protocol/sync data (EBCDIC) (NRZ) |
|
&M10 |
V.25bis dialer w/SDLC protocol/sync data (ASCII) (NRZI) |
|
&M11 |
V.25bis dialer w/SDLC protocol/sync data (EBCID) (NRZI) |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
í &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe) |
|
RTS/CTS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Rn [cmds] |
|
Description: |
Selects RTS/CTS options |
|
Command |
Function |
|
í &R0 |
CTS follows RTS in data mode; RTS is ignored in command mode. |
|
&R1 |
CTS forced high, RTS is ignored. |
|
&R2 |
CTS follows DCD |
|
&R9 |
CTS equals RTS |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
í &S1 |
DSR high when ready to accept data |
|
&S2 |
DSR off for 5 seconds after disconnect |
|
&S3 |
DSR follows off hook |
|
CONFIGURATION PROFILES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &V [cmds] |
|
Description: |
Displays active and stored configuration profiles |
|
Command |
Function |
|
&V0 |
View configuration profiles |
|
&V1 |
Displays received signal status |
|
&V2 |
Displays active profile |
Extended AT Commands
|
BREAK SEND | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Bn [cmds] |
|
Default: |
35 |
|
Range: |
1-255 |
|
Unit: |
20ms |
|
Description: |
Sends break to modem |
|
Command |
Function |
|
\B0 |
Transmit break signal |
|
\B1 |
Set break length in 20ms increments |
|
AUTO-RELIABLE TIME BUFFER CONFIGURATION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Cn [cmds] |
|
Description: |
Controls the handling of incoming data during auto-reliable time period |
|
Command |
Function |
|
\C0 |
Data is discarded |
|
\C1 |
Data is buffered |
|
LOCK SERIAL PORT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Jn [cmds] |
|
Description: |
Sets operation of serial port speed |
|
Command |
Function |
|
\J0 |
Serial speed locked |
|
\J1 |
Serial speed follows connect speed |
|
\J2 |
Enable 230.4Kbps serial speed |
|
\J3 |
Disable 230.4Kbps serial speed |
|
BREAK TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Kn [cmds] |
|
Description: |
Configures action of break signal |
|
Command |
Function |
|
\K1 |
Break signals empty data buffers |
|
\K3 |
Expedite break signals |
|
\K5 |
Sequence break signals with data |
|
V.42 FAST DETECT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Mn [cmds] |
|
Description: |
Controls the V.42 fast detect data sequence |
|
Command |
Function |
|
\M0 |
V.42 fast detect data sequence disabled |
|
\M1 |
V.42 fast detect data sequence enabled |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
MNP mode |
|
\N3 |
MNP with normal fallback |
|
\N4 |
LAPM only |
|
\N5 |
LAPM with normal fallback |
|
\N6 |
LAPM with MNP fallback |
|
\N7 |
LAPM with MNP and normal fallback |
|
FLOW CONTROL TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Qn [cmds] |
|
Description: |
Sets type of flow control used by modem |
|
Command |
Function |
|
\Q0 |
Flow control disabled |
|
\Q1 |
Bidirectional XON/XOFF flow control enabled |
|
\Q2 |
CTS flow control by DCE enabled |
|
\Q3 |
Bidirectional RTS/CTS flow control enabled |
|
RING INDICATE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Rn [cmds] |
|
Description: |
Controls the ring indicator |
|
Command |
Function |
|
\R0 |
LED AA blinks for ring and remains on during the call |
|
\R1 |
LED AA blinks for ring and turns off when call is answered |
|
INACTIVITY TIMER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Tn [cmds] |
|
Range: |
1-255 |
|
Unit: |
1 second |
|
Description: |
Sets the length of time that the modem does not receive information before it disconnects. |
|
EXTENDED RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Vn [cmds] |
|
Description: |
Selects extended result codes |
|
Command |
Function |
|
\V0 |
Connect message shows computer speed |
|
\V1 |
Connect message shows computer speed/protocol |
|
\V2 |
Connect message shows modem speed |
|
\V3 |
Connect message shows speed/protocol |
|
\V4 |
Connect message shows modem speed/modulation/protocol |
|
SPEED SELECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Bn [cmds] |
|
Description: |
Selects the maximum connect speed |
|
Command |
Function |
|
%B0 |
Use computer speed |
|
%B1 |
300bps |
|
%B2 |
1200bps |
|
%B3 |
2400bps |
|
%B4 |
4800bps |
|
%B5 |
9600bps uncoded |
|
%B6 |
9600bps |
|
%B7 |
7200bps |
|
%B8 |
12000bps |
|
%B9 |
14400bps |
|
%B10 |
600bps |
|
%B11 |
16800bps |
|
%B12 |
19200bps |
|
%B13 |
21600bps |
|
%B14 |
24000bps |
|
%B15 |
26400bps |
|
%B16 |
28800bps |
|
%B17 |
31200bps |
|
%B18 |
33600bps |
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
%C0 |
Compression disabled |
|
%C1 |
Compression enabled on transmit and receive data |
|
DISCONNECT BUFFER DELAY | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Dn [cmds] |
|
Description: |
Controls the disconnect buffer delay |
|
Command |
Function |
|
%D0 |
Disable disconnect buffer delay |
|
%D1 |
Set disconnect buffer delay in seconds n (n= 1 - 255) |
|
MINIMUM SPEED SELECTION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %L [cmds] |
|
Description: |
Sets the minimum speed level |
|
Command |
Function |
|
%L0 |
300bps |
|
%L1 |
300bps |
|
%L2 |
1200bps |
|
%L3 |
2400bps |
|
%L4 |
4800bps |
|
%L5 |
9600bps uncoded |
|
%L6 |
9600bps |
|
%L7 |
7200bps |
|
%L8 |
12000bps |
|
%L9 |
14400bps |
|
%L10 |
600bps |
|
%L11 |
16800bps |
|
%L12 |
19200bps |
|
%L13 |
21600bps |
|
%L14 |
24000bps |
|
%L15 |
26400bps |
|
%L16 |
28800bps |
|
%L17 |
31200bps |
|
%L18 |
33600bps |
|
REMOTE CONFIGURATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %P [cmds] |
|
Description: |
Displays the remote configuration code |
|
AUTOMATIC RATE ADAPTION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Rn [cmds] |
|
Description: |
Send PTT test signals for a line tests |
|
Command |
Function |
|
%R0 |
Disable automatic rate adaption |
|
%R1 |
Enable automatic rate adaption low BER |
|
%R2 |
Enable automatic rate adaption medium BER |
|
%R3 |
Enable automatic rate adaption using high BER |
|
TEST PATTERN | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Tn [cmds] |
|
Description: |
Transmit test pattern |
|
PRODUCT REVISION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %Vn [cmds] |
|
Description: |
Display product revision level |
|
V.34 ASYMMETRIC RATE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *ASn [cmds] |
|
Description: |
Sets the asymmetric bit rate |
|
Command |
Function |
|
*AS0 |
Disable V.34 asymmetric bit rate |
|
*AS1 |
Enable V.34 asymmetric bit rate |
|
BILTERAL DIGITAL LOOP | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *DGn [cmds] |
|
Description: |
Controls the bilateral digital loop |
|
Command |
Function |
|
*DG0 |
Disables the bilateral digital loop |
|
*DG1 |
Enables the digital bilateral loop |
|
TEST MODE - PTT | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *DNn [cmds] |
|
Description: |
Send PTT test signals for a line tests |
|
Command |
Function |
|
*DN0 |
Allow redial with A/ |
|
*DN1 |
Disallow redial with A/ |
|
DISTINCTIVE RING DETECTION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *DRn [cmds] |
|
Description: |
Controls the distinctive ring detection |
|
Command |
Function |
|
*DR0 |
Disable distinctive ring detection |
|
*DR1 |
Enable distinctive ring detection |
|
FAST TRAIN | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *FTn [cmds] |
|
Description: |
Controls the fast train |
|
Command |
Function |
|
*FT0 |
Disables the fast train |
|
*FT1 |
Enables the fast train |
|
CALLER ID | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *IDn [cmds] |
|
Description: |
Controls the caller ID function |
|
Command |
Function |
|
*ID0 |
Disable caller ID |
|
*ID1 |
Enable caller ID |
|
MODULATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *MMn [cmds] |
|
Description: |
Sets the modulation |
|
Command |
Function |
|
*MM0 |
Automode |
|
*MM1 |
V.21 |
|
*MM2 |
Bell 103J |
|
*MM3 |
V.23 |
|
*MM4 |
Bell 212A |
|
*MM5 |
V.22bis |
|
*MM11 |
V.32bis |
|
*MM12 |
V.34 |
|
STORED NUMBERS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *ND [cmds] |
|
Description: |
Displays the nine stored numbers |
|
AT COMMANDSET | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *NTn [cmds] |
|
Description: |
Controls the AT command set |
|
Command |
Function |
|
*NT0 |
AT command set disabled |
|
*NT1 |
AT command set enabled |
|
MODE SELECTION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *ORn [cmds] |
|
Description: |
Controls the originate or answer mode |
|
Command |
Function |
|
*OR0 |
Originate mode active |
|
*OR1 |
Answer mode active |
|
RATE NEGOTIATION SELECTION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *RRn [cmds] |
|
Description: |
Sets the rate negotiation |
|
Command |
Function |
|
*RR0 |
Rate negotiation to 2400 |
|
*RR1 |
Rate negotiation to 4800 |
|
*RR2 |
Rate negotiation to 7200 |
|
*RR3 |
Rate negotiation to 9600 |
|
*RR4 |
Rate negotiation to 12000 |
|
*RR5 |
Rate negotiation to 14400 |
|
*RR6 |
Rate negotiation to 16800 |
|
*RR7 |
Rate negotiation to 19200 |
|
*RR8 |
Rate negotiation to 21600 |
|
*RR9 |
Rate negotiation to 24000 |
|
*RR10 |
Rate negotiation to 26400 |
|
*RR11 |
Rate negotiation to 28800 |
|
*RR12 |
Rate negotiation to 31200 |
|
*RR13 |
Rate negotiation to 33600 |
|
RATE ADAPTION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *RUn [cmds] |
|
Description: |
Controls the rate adaption |
|
Command |
Function |
|
*RU0 |
Disable auto rate adaption above initial rate |
|
*RU1 |
Enable auto rate adaption above initial rate |
|
TRANSMIT LEVEL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *TDn [cmds] |
|
Description: |
Set dial transmit level from -9 to -30dBm |
|
RATE SELECTION THRESHOLD | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *THn [cmds] |
|
Description: |
Sets the rate selection threshold |
|
Command |
Function |
|
*TH0 |
Low V.34 rate selection threshold |
|
*TH1 |
Medium V.34 rate selection threshold |
|
*TH2 |
High V.34 rate selection threshold |
|
LEASED LINE TRANSMIT LEVEL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *TLn [cmds] |
|
Description: |
Sets the leased line transmit level (0 - 30) |
|
ONLINE HELP | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $Hn [cmds] |
|
Description: |
Online help |
|
Command |
Function |
|
$H=string |
Online help |
|
PRODUCT SERIAL NUMBER | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $Vn [cmds] |
|
Description: |
Displays the product serial number |
Security Commands
|
USER CALLBACK NUMBER | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $Cn=m [cmds] |
|
Description: |
Sets the user callback number (n= user number and m= the callback number |
|
SECURITY DISABLED | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $D [cmds] |
|
Description: |
Disables security |
|
SECURITY STATUS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $D? [cmds] |
|
Description: |
Reports the security status |
|
SECURITY ENABLE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $EH=pw [cmds] |
|
Description: |
Enables security (pw=superuser password) |
|
REINITIALIZE SECURITY | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $F=pw$pw [cmds] |
|
Description: |
Reinitializes security (pw=superuser password) |
|
USER INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $I [cmds] |
|
Description: |
Reports all secure user information |
|
SECURITY LEVEL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $Ln=m [cmds] |
|
Description: |
Set security level for the user specified by n |
|
ILLEGAL ATTEMPTS INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $M [cmds] |
|
Description: |
Reports illegal attempts information |
|
RESET ALL ILLEGAL ATTEMPTS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $M* [cmds] |
|
Description: |
Reset all illegal attempts registers/restore suspended users to normal status |
|
RESET ILLEGAL ATTEMPTS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $Mn [cmds] |
|
Description: |
Reset illegal attempts registers/restore suspended users to normal status |
|
LOCAL LOGON | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $n=pw [cmds] |
|
Description: |
Local logon (n = user number, pw = password) |
|
SET PASSWORD | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $Pn=pw$pw [cmds] |
|
Description: |
Set user password (n = user number, pw = new password, n = 0 for superuser password) |
|
REMOVE USER | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $Rn [cmds] |
|
Description: |
Removes a user |
|
SUPERUSER STATUS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $S=pw [cmds] |
|
Description: |
Request superuser status (pw = password) |
|
CURRENT USER STATUS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $S? [cmds] |
|
Description: |
Reports current user status |
|
LOCAL LOGON | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $n=m [cmds] |
|
Description: |
Local logon (n = user number and m = password) |
Remote Configuration Commands
|
REMOTE CONFIGURATION SECURITY | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %P=n [cmds] |
|
Description: |
Set the remote configuration security code to value n |
|
DISPLAY SECURITY CODE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %P? [cmds] |
|
Description: |
Displays the remote configuration security code |
|
CLEAR SECURITY CODE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] %P = (blank) [cmds] |
|
Description: |
Clears the security code |
|
COMPUTER SPEED | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *RBn [cmds] |
|
Description: |
Sets the remote configuration computer speed |
|
Command |
Function |
|
*RB0 |
300bps |
|
*RB1 |
600bps |
|
*RB2 |
1200bps |
|
*RB3 |
2400bps |
|
*RB4 |
4800bps |
|
*RB5 |
7200bps |
|
*RB6 |
9600bps |
|
*RB7 |
12000bps |
|
*RB8 |
14400bps |
|
*RB9 |
16800bps |
|
*RB10 |
19200bps |
|
*RB11 |
21600bps |
|
*RB12 |
24000bps |
|
*RB13 |
26400bps |
|
*RB14 |
28800bps |
|
*RB15 |
28400bps |
|
*RB16 |
57600bps |
|
*RB17 |
115200bps |
|
FORMAT SETTINGS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *RFn [cmds] |
|
Description: |
Sets the remote configuration format settings |
|
Command |
Function |
|
*RF0 |
7 data bits, mark parity, 1 stop bit |
|
*RF1 |
7 data bits, no parity, 2 stop bit |
|
*RF2 |
7 data bits, odd parity, 1 stop bit |
|
*RF3 |
7 data bits, even parity, 1 stop bit |
|
*RF4 |
8 data bits, mark parity, 1 stop bit |
|
*RF5 |
8 data bits, no parity, 1 stop bit |
|
*RF6 |
8 data bits, odd parity, 1 stop bit |
|
*RF7 |
8 data bits, even parity, 1 stop bit |
|
SAVE REMOTE CONFIGURATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] *RQn [cmds] |
|
Description: |
Exit remote configuration and saves or discards the new configuration |
|
Command |
Function |
|
*RQ0 |
Save new configuration |
|
*RQ1 |
Discard new configuration |
S(status) -REGISTERS
|
REMOTE ESCAPE CHARACTER | |
|
Format |
AT [cmds] S41=n [cmds] |
|
Default: |
61 |
|
Range: |
1-255 |
|
Unit: |
20ms |
|
Description: |
Sets the remote escape character |
|
REMOTE GUARD TIME | |
|
Format |
AT [cmds] S42=n [cmds] |
|
Default: |
50 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the remote guard time |
|
COMPUTER CONTROL CHARACTER - XON | |
|
Format |
AT [cmds] S44=n [cmds] |
|
Default: |
17 |
|
Range: |
0-127 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XON for the computer |
|
COMPUTER CONTROL CHARACTER - XOFF | |
|
Format |
AT [cmds] S45=n [cmds] |
|
Default: |
19 |
|
Range: |
0-127 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XOFF for the computer |
|
MODEM CONTROL CHARACTER - XON | |
|
Format |
AT [cmds] S49=n [cmds] |
|
Default: |
17 |
|
Range: |
0-127 |
|
Description: |
Sets the character used to represent XON for the modem |
|
MODEM CONTROL CHARACTER - XOFF | |
|
Format |
AT [cmds] S50=n [cmds] |
|
Default: |
19 |
|
Range: |
0-127 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XOFF for the modem |
|
PASSWORD TIMEOUT SECURITY | |
|
Format |
AT [cmds] S73=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Description: |
Sets the password timeout security |
|
CALLBACK DELAY | |
|
Format |
AT [cmds] S74=n [cmds] |
|
Default: |
15 |
|
Range: |
0-255 |
|
Description: |
Sets the callback delay |
|
CALLBACK RETRY | |
|
Format |
AT [cmds] S75=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Description: |
Sets the callback retry |
|
CALLBACK RETRY DELAY | |
|
Format |
AT [cmds] 76=n [cmds] |
|
Default: |
15 |
|
Range: |
1-255 |
|
Description: |
Sets the callback retry delay |
|
LOCKOUT THRESHOLD | |
|
Format |
AT [cmds] S77=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Description: |
Sets the lockout threshold |
