MAXTECH CORPORATION
XPVS 56E (SF-1156V/T3(x2))
|
Card Type |
Modem, Fax |
|
Chip Set |
Unidentified |
|
I/O Options |
Microphone in, speaker out, line in, line out, DC power, serial port |
|
Maximum Modem Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A, V.22, V.22bis, V.23, V.32, V.32bis, V.34+, x2 |
|
Fax Modulation Protocol |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42bis |
|
Fax Class |
Class I & II |
|
Data Bus |
External |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line in |
CN1 |
Microphone in |
CN5 | |||
|
Line out |
CN2 |
Speaker |
CN6 | |||
|
Serial port |
CN3 |
Volume |
R1 | |||
|
DC power |
CN4 |
Power switch |
SW1 | |||
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
ARQ |
Unidentified |
On |
MNP or V.42 connection is established |
|
ARQ |
Unidentified |
Blinking |
Data is re-sent |
|
ARQ |
Unidentified |
Off |
No connection established |
|
AA |
Unidentified |
On |
Auto-answer enabled |
|
AA |
Unidentified |
Blinking |
Phone is ringing |
|
AA |
Unidentified |
Off |
No line activity present |
|
CD |
Unidentified |
On |
Carrier signal detected |
|
CD |
Unidentified |
Off |
Carrier signal not detected |
|
OH |
Unidentified |
On |
Modem has gone off hook |
|
OH |
Unidentified |
Off |
Modem is on hook |
|
RD |
Unidentified |
On |
Data is being sent to the computer through the modem |
|
RD |
Unidentified |
Off |
No data is being sent |
|
SD |
Unidentified |
On |
Modem is receiving data from the computer |
|
SD |
Unidentified |
Off |
Modem is not receiving data from the computer |
|
TR |
Unidentified |
On |
Modem can receive commands |
|
TR |
Unidentified |
Off |
Modem cannot receive commands |
|
MR |
Unidentified |
On |
The modem is turned on |
|
MR |
Unidentified |
Off |
The modem is turned off |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, ‘+++’, A/ |
|
A, B, E, F, H, M, O, P, T, V, X |
|
&C, &G, &T, &W, &Z |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25 |
|
Special Commands |
|
#BDR, #CLS, #CID, #MDL?, #MFR?, #REV?, #TL, #VBQ?, #VBS, #VBT, #VCI?, #VLS, #VRA, #VRN, #VRX, |
|
#VSD, #VSK, #VSP, #VSR, #VSS, #VTD, #VTS, #VTX, +MS, +MS? |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
ACTIVE/DEFAULT PROFILE CONFIGURATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Zn [cmds] |
|
Description: |
Determines which profile the modem should use upon power-up or reset. |
|
Command |
Function |
|
Z0 |
Reset and retrieve the profile set by the ‘Y’ command |
|
Z1 |
Reset and retrieve active Profile 0 |
|
Z2 |
Reset and retrieve active Profile 1 |
|
Z3 |
Reset and retrieve default Profile 0 |
|
Z4 |
Reset and retrieve default Profile 1 |
|
Z5 |
Reset and retrieve default Profile 2 |
|
ANSWER MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Configures modem to either answer in U.S. answer mode or V.25 answer mode. |
|
Command |
Function |
|
í B0 |
Sets modem for ITU-T V.25 answer mode |
|
B1 |
Sets modem for U.S. answer mode |
|
AUTOMATIC REPEAT REQUEST | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &An [cmds] |
|
Description: |
Configures ARQ result codes, V.32, error correction, and compression protocols |
|
Command |
Function |
|
&A0 |
ARQ result codes disabled |
|
&A1 |
ARQ result codes enabled |
|
&A2 |
ARQ result codes and V.32 enabled |
|
í &A3 |
ARQ result codes, V.32, error correction, and data compression enabled |
|
BREAK CONFIGURATION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Yn [cmds] |
|
Description: |
Configures Line Break |
|
Command |
Function |
|
&Y0 |
Destructive break / Does not send break |
|
&Y1 |
Destructive break / Break expedited |
|
&Y2 |
Non-destructive break / Break expedited |
|
COMMAND SET | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] $ [cmds] |
|
Description: |
Displays modem command sets |
|
&$ |
Displays the ampersand command set |
|
COMMUNICATIONS MODE (ASYNCHRONOUS) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Mn [cmds] |
|
Description: |
Selects communications mode |
|
Command |
Mode |
|
í &M0 |
Set to normal mode |
|
&M4 |
Enable ARQ and normal modes |
|
&M5 |
Only enables ARQ mode |
|
CONNECTION SPEED | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Nn [cmds] |
|
Description: |
Configures modem connection speed |
|
Command |
Function |
|
&N0 |
Automode enabled |
|
&N1 |
Connection speed set to 300bps |
|
&N2 |
Connection speed set to 1200bps |
|
&N3 |
Connection speed set to 2400bps |
|
&N4 |
Connection speed set to 4800bps |
|
&N5 |
Connection speed set to 7200bps |
|
&N6 |
Connection speed set to 9600bps |
|
&N7 |
Connection speed set to 12Kbps |
|
&N8 |
Connection speed set to 14.4Kbps |
|
&N9 |
Connection speed set to 16.8Kbps |
|
&N10 |
Connection speed set to 19.2Kbps |
|
&N11 |
Connection speed set to 21.6Kbps |
|
&N12 |
Connection speed set to 24Kbps |
|
&N13 |
Connection speed set to 26.4Kbps |
|
&N14 |
Connection speed set to 28.8Kbps |
|
&N15 |
Connection speed set to 31.2Kbps |
|
&N16 |
Connection speed set to 33.6Kbps |
|
&N17 |
Connection speed set to 33.333Kbps |
|
&N18 |
Connection speed set to 37.333Kbps |
|
&N19 |
Connection speed set to 41.333Kbps |
|
&N20 |
Connection speed set to 42.666Kbps |
|
&N21 |
Connection speed set to 44Kbps |
|
&N22 |
Connection speed set to 45.333Kbps |
|
&N23 |
Connection speed set to 46.666Kbps |
|
&N24 |
Connection speed set to 48Kbps |
|
&N25 |
Connection speed set to 49.333Kbps |
|
&N26 |
Connection speed set to 50.666Kbps |
|
&N27 |
Connection speed set to 52Kbps |
|
&N28 |
Connection speed set to 53.333Kbps |
|
&N29 |
Connection speed set to 54.666Kbps |
|
&N30 |
Connection speed set to 56Kbps |
|
&N31 |
Connection speed set to 57.333Kbps |
|
DATA COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enable/disable Auto Data, V.42bis, and MNP5 compression |
|
Command |
Function |
|
&K0 |
V.42bis and MNP5 compression disabled |
|
í &K1 |
Auto Data compression enabled |
|
&K2 |
V.42bis and MNP5 compression enabled |
|
&K3 |
MNP5 compression disabled |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
í &S0 |
DSR forced high |
|
&S1 |
DSR is off while in command mode and set on in on-line mode |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
|
Command |
Function |
|
í &D0 |
Modem does not respond to DTR |
|
&D1 |
Modem goes to command mode after DTR goes is off |
|
&D2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. |
|
DCE CONNECTION SPEED | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Un [cmds] |
|
Description: |
Configures DCE modem connection speed |
|
Command |
Function |
|
&U0 |
Variable DCE connection speed enabled |
|
&U1 |
Connection speed set to 300bps |
|
&U2 |
Connection speed set to 1200bps |
|
&U3 |
Connection speed set to 2400bps |
|
&U4 |
Connection speed set to 4800bps |
|
&U5 |
Connection speed set to 7200bps |
|
&U6 |
Connection speed set to 9600bps |
|
&U7 |
Connection speed set to 12Kbps |
|
&U8 |
Connection speed set to 14.4Kbps |
|
&U9 |
Connection speed set to 16.8Kbps |
|
&U10 |
Connection speed set to 19.2Kbps |
|
&U11 |
Connection speed set to 21.6Kbps |
|
&U12 |
Connection speed set to 24Kbps |
|
&U13 |
Connection speed set to 26.4Kbps |
|
&U14 |
Connection speed set to 28.8Kbps |
|
&U15 |
Connection speed set to 31.2Kbps |
|
&U16 |
Connection speed set to 33.6Kbps |
|
&U17 |
Connection speed set to 33.333Kbps |
|
&U18 |
Connection speed set to 37.333Kbps |
|
&U19 |
Connection speed set to 41.333Kbps |
|
&U20 |
Connection speed set to 42.666Kbps |
|
&U21 |
Connection speed set to 44Kbps |
|
&U22 |
Connection speed set to 45.333Kbps |
|
&U23 |
Connection speed set to 46.666Kbps |
|
&U24 |
Connection speed set to 48Kbps |
|
&U25 |
Connection speed set to 49.333Kbps |
|
&U26 |
Connection speed set to 50.666Kbps |
|
&U27 |
Connection speed set to 52Kbps |
|
&U28 |
Connection speed set to 53.333Kbps |
|
&U29 |
Connection speed set to 54.666Kbps |
|
&U30 |
Connection speed set to 56Kbps |
|
&U31 |
Connection speed set to 57.333Kbps |
|
DCE/DTE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Bn [cmds] |
|
Description: |
Adjust DCE/DTE rate settings |
|
Command |
Function |
|
&B0 |
DTE follows DCE |
|
í &B1 |
DTE constant |
|
&B2 |
DTE constant in ARQ mode and a variable rate in non-ARQ mode |
|
DIAL MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Dn [cmds] |
|
Description: |
Configures the dialing mode the modem will use. |
|
Command |
Function |
|
DL |
Redials last number |
|
DP |
Uses pulse dialing |
|
DS=n |
Dial number in stored memory |
|
DR |
Reverses the dial mode |
|
í DT |
Uses touch-tone dialing |
|
DW |
Waits for two dial tones |
|
D, |
Pause |
|
D; |
Modem returns to &Dmode after dialing |
|
D/ |
Uses a 125 msec delay before dialing |
|
D! |
Uses flash |
|
D@ |
Set to wait for 5 seconds of line silence |
|
D$ |
Displays the dialing commands |
|
ECHO COMMANDS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] En [cmds] |
|
Description: |
Configures modem to either echo commands or not to echo commands |
|
Command |
Function |
|
E0 |
Local echo enabled |
|
í E1 |
Local echo disabled |
|
FACTORY DEFAULT PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &F [cmds] |
|
Description: |
Sets values in active profile to values found in the default profile |
|
Command |
Function |
|
&F0 |
Restore default configuration 0 |
|
í &F1 |
Restore default configuration 1 (enables hardware flow control) |
|
&F2 |
Restore default configuration 2 (enables software flow control) |
|
MODEM RESPONSE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Qn [cmds] |
|
Description: |
Determines when and how the modem sends reponses |
|
Command |
Function |
|
í Q0 |
Result code sending enabled |
|
Q1 |
Result code sending disabled |
|
Q2 |
Displays result codes when modem is set in Originate mode |
|
PROFILE CONFIGURATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Yn [cmds] |
|
Description: |
Determines which profile the modem should use upon power-up or reset. |
|
Command |
Function |
|
Y0 |
Set Profile 0 active upon power-up or reset |
|
Y1 |
Set profile 1 active upon power-up or reset |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
í &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe and Hong Kong) |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product identification code |
|
I1 |
Reports ROM checksum |
|
I2 |
Reports internal memory test |
|
I3 |
Reports product identification |
|
I4 |
Reports current modem settings |
|
I5 |
Reports active and stored profiles |
|
I6 |
Reports link diagnostics |
|
I7 |
Reports modem configuration |
|
RTS/CTS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Rn [cmds] |
|
Description: |
Selects RTS/CTS options |
|
Command |
Function |
|
&R0 |
Reserved |
|
&R1 |
CTS forced high, RTS is ignored. |
|
í &R2 |
RX hardware flow control enabled |
|
RX FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &In [cmds] |
|
Description: |
Configure RX & ENQ/ACK flow control settings (XON/XOFF) |
|
Command |
Function |
|
í &I0 |
Software RX flow control disabled |
|
&I1 |
Software RX flow control enabled |
|
&I2 |
RX flow control enabled without passthrough |
|
&I3 |
ENQ/ACK flow control enabled in host mode |
|
&I4 |
ENQ/ACK flow control enabled in terminal mode |
|
&I5 |
Software RX flow control enabled for non-ARQ mode |
|
SPEAKER VOLUME | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls the volume of the modem speaker |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
í L2 |
Medium volume setting |
|
L3 |
High volume setting |
|
Description: |
Controls 8S-2D, 16S-4D, 32S-2D, and 64S-4D trellis coding. |
|
TX FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Hn [cmds] |
|
Description: |
Configure TX flow control settings (XON/XOFF) |
|
Command |
Function |
|
&H0 |
CTS flow control disabled |
|
í &H1 |
CTS flow control enabled |
|
&H2 |
Software flow control enabled |
|
&H3 |
Software flow control and CTS enabled |
S(status) -Registers
|
BIT-MAPPED REGISTER S13 | |
|
Format: |
AT [cmds] S13=n [cmds] |
|
Default: |
0 |
|
Unit: |
Bit-mapped |
|
Description: |
Controls RX flow control, buffer reset, backspace, autodial, retrain, and hang-up commands. |
|
BIT-MAPPED REGISTER S27 | |
|
Format |
AT [cmds] S27=n [cmds] |
|
Default: |
0 |
|
Unit: |
Bit-mapped |
|
Description: |
Controls V.21, V.23, V.32, V.32bis, trellis coding, answer tone, and 9600bps result codes. |
|
BREAK LENGTH | |
|
Format |
AT [cmds] S21 [cmds] |
|
Default: |
10 |
|
Range: |
0-255 |
|
Unit: |
.01 second |
|
Description: |
Determines the break length |
|
COMPRESSION CONFIGURATION | |
|
Format |
AT [cmds] S15 [cmds] |
|
Default: |
0 |
|
Range: |
Unidentified |
|
Unit: |
Bit-mapped register |
|
Description: |
Disable ARQ/MNP/V.42bis compression |
|
COMPRESSION PROTOCOLS | |
|
Type: |
Register |
|
Format: |
AT [cmds] S32=n [cmds] |
|
Default: |
2 |
|
Unit: |
Bit-mapped register |
|
Description: |
Controls V.8, V.34, V.34bis, and x2 compression protocols |
|
DIAL LINE RATE | |
|
Type: |
Register |
|
Format |
AT [cmds] S38=n [cmds] |
|
Default: |
0 |
|
Range: |
0 - 19 |
|
Unit: |
Unidentified |
|
Description: |
Sets the 56K dialing rate |
|
DISTINCTIVE RING | |
|
Format |
AT [cmds] S41 [cmds] |
|
Default: |
0 |
|
Range: |
0-1 |
|
Unit: |
Bit-mapped register |
|
Description: |
Enables or disables the distinctive ring function on the modem |
|
DTR HANG-UP DELAY | |
|
Type: |
Register |
|
Format |
AT [cmds] S38=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
1 second |
|
Description: |
Controls the DTR hang-up delay time |
|
FLOW CONTROL CHARACTER - XON | |
|
Format |
AT [cmds] S22 [cmds] |
|
Default: |
17 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XON |
|
FLOW CONTROL CHARACTER - XOFF | |
|
Format |
AT [cmds] S23 [cmds] |
|
Default: |
19 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XOFF |
|
INACTIVITY TIMER | |
|
Format |
AT [cmds] S19 [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
minutes |
|
Description: |
Disconnects line connection after a certain period of line inactivity |
|
SYMBOL RATES | |
|
Type: |
Register |
|
Format: |
AT [cmds] S33=n [cmds] |
|
Default: |
0 |
|
Unit: |
Bit-mapped register |
|
Description: |
Controls 2400, 2743, 2800, 3000, 3200, and 3429 symbol rates. |
|
TRELLIS CODING | |
|
Type: |
Register |
|
Format: |
AT [cmds] S34=n [cmds] |
|
Default: |
0 |
|
Unit: |
Bit-mapped register |
|
V.21 ANSWER MODE TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S29=n [cmds] |
|
Default: |
20 |
|
Range: |
0-255 |
|
Unit: |
.01 second |
|
Description: |
Time the modem will go on-hook upon receiving the ! dial modifier in dial string. |
|
V.32 ANSWER TONE | |
|
Format |
AT [cmds] S28=n [cmds] |
|
Default: |
8 |
|
Range: |
0-255 |
|
Unit: |
.1 seconds |
|
Description: |
Controls V.32 answer tone |
