MAXTECH CORPORATION
XPVS T2 (SF-1133HV/T2)
|
Card Type |
Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
I/O Options |
Microphone, speaker out, line in, line out |
|
Maximum Modem Rate |
33.6Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34, V.34+, V.FC |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
8-bit ISA |
|
Card Size |
Half-length, half-height card |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line out |
CN1 |
Microphone |
CN3 | |||
|
Line in |
CN2 |
Speaker out |
CN4 | |||
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
Speaker type stereo |
JP5 |
Closed |
|
Speaker type mono |
JP5 |
Open |
|
SERIAL PORT ADDRESS | |||
|
Setting |
JP3/A |
JP3/B |
JP3/C |
|
COM1 (3F8h) |
Closed |
Closed |
Closed |
|
COM2 (2F8h) |
Open |
Closed |
Closed |
|
COM3 (3E8h) |
Closed |
Open |
Closed |
|
COM4 (2E8h) |
Open |
Open |
Closed |
|
PnP |
Open |
Open |
Open |
|
INTERRUPT SELECTION | |||||
|
IRQ |
JP2/A |
JP2/B |
JP2/C |
JP2/D |
JP2/E |
|
2/9 |
Closed |
Open |
Open |
Open |
Open |
|
3 |
Open |
Closed |
Open |
Open |
Open |
|
4 |
Open |
Open |
Closed |
Open |
Open |
|
5 |
Open |
Open |
Open |
Closed |
Open |
|
7 |
Open |
Open |
Open |
Open |
Closed |
|
PnP |
Open |
Open |
Open |
Open |
Open |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, ‘+++’, A/ |
|
A, B, E, F, H, M, O, P, T, V, X |
|
&C, &G, &T, &W, &Z |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25 |
|
Voice Commands |
|
#BDR, #CLS, #MDL, #MFR, #VBQ?, #VBS, #VBT, #VBT, #VCI, #VLS, #VLS, #VRA, #VRA, #VRN, #VRN, |
|
#VRX, #VSD, #VSD, #VSK, #VSK, #VSP, #VSP, #VSR, #VSR, #VSS, #VSS, #VTD, #VTD, #VTS, #VTX |
Proprietary AT Command Set
|
DISPLAY COMMAND SET | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] $ [cmds] |
|
Description: |
Displays basic command set |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DR |
Reverse dial mode |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D/ |
Delay 125 msec before dialing |
|
D$ |
Display dialing commands |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports modem model and speed |
|
I1 |
Reports ROM checksum |
|
I2 |
Tests and reports ROM checksum |
|
I3 |
Reports product ID |
|
I4 |
Reports current modem settings |
|
I5 |
Reports active and stored profiles |
|
I6 |
Reports link diagnostics |
|
I7 |
Product configuration |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
í L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
|
RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Qn [cmds] |
|
Description: |
Enables modem to send result codes to the DTE |
|
Command |
Function |
|
í Q0 |
Modem sends responses |
|
Q1 |
Modem does not send responses |
|
Q2 |
Displays result codes only in Originate Mode |
|
LONG SPACE DISCONNECT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Yn [cmds] |
|
Description: |
Commands the modem to disconnect after a 1.6 second break is detected |
|
Command |
Function |
|
í Y0 |
Configuration profile 0 active upon power on or reset |
|
Y1 |
Configuration profile 1 active upon power on or reset |
|
Y2 |
Factory configuration 0 active upon power on or reset |
|
Y3 |
Factory configuration 1 active upon power on or reset |
|
Y4 |
Factory configuration 2 active upon power on or reset |
|
Y6 |
Reports link diagnostics |
|
SOFT RESET | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Zn [cmds] |
|
Description: |
Restores modem profiles previously saved in non-volatile RAM using the &W command. |
|
Command |
Function |
|
Z0 |
Reset and retrieve active profiles set by the Y command |
|
Z1 |
Reset and retrieve active profile 0 |
|
Z2 |
Reset and retrieve active profile 1 |
|
Z3 |
Reset and retrieve factory default profile 0 |
|
Z4 |
Reset and retrieve factory default profile 1 |
|
Z5 |
Reset and retrieve factory default profile 2 |
|
ARQ RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &An [cmds] |
|
Description: |
Selects ARQ result code settings |
|
Command |
Function |
|
&A0 |
Disable ARQ result codes |
|
&A1 |
Enable ARQ result codes |
|
&A2 |
Disable ARQ result codes and V.32 modulation |
|
í &A3 |
Enable ARQ result codes and error correction and data compression protocols |
|
DTE RATE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Bn [cmds] |
|
Description: |
Controls DTE rate |
|
Command |
Function |
|
&B0 |
DTE rate adjust to DCE rate after on-line |
|
í &B1 |
Constant DTE rate |
|
&B2 |
Constant DTE rate in ARQ mode, variable in non-ARQ mode |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
Note: The action each variant of &D causes depends on the setting of &Q | |
|
Command |
Function |
|
í &D0 |
Modem does not respond to DTR |
|
&D1 |
Modem goes to command mode after DTR goes is off |
|
&D2 |
Modem hands up and returns to the command mode after DTR toggle |
|
FACTORY DEFAULT PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &F [cmds] |
|
Description: |
Sets values in active profile to values found in the default profile |
Note: Used primarily for international data transmission | |
|
Command |
Function |
|
&F0 |
Recall factory default configuration 0 |
|
í &F1 |
Recall factory default configuration profile 1 (hardware flow control enabled) |
|
&F2 |
Recall factory default configuration profile 2 (software flow control enabled) |
|
TX FLOW | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Hn [cmds] |
|
Description: |
Controls TX flow settings |
Note: Used primarily for international data transmission | |
|
Command |
Function |
|
&H0 |
Disable TX flow control |
|
í &H1 |
Enable hardware TX flow control (CTS) |
|
&H2 |
Enable software TX flow control (XON/XOFF) |
|
&H3 |
Enable hardware (CTS) and software (XON/XOFF) TX flow control |
|
RX FLOW | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &In [cmds] |
|
Description: |
Controls RX flow settings |
Note: Used primarily for international data transmission | |
|
Command |
Function |
|
í &I0 |
Disable software RX flow control |
|
&I1 |
Enable software RX flow control (XON/XOFF) |
|
&I2 |
Enable software RX flow control (XON/XOFF), but do not pass XON/XOFF to remote modem or local DTE |
|
&I3 |
Enable HP ENQ/ACK software flow control, host mode |
|
&I4 |
Enable HP ENQ/ACK software flow control, terminal mode |
|
&I5 |
Enable software RX flow control (XON/XOFF) for non-ARQ mode |
|
COMPRESSION CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables compression control options |
|
Command |
Function |
|
&K0 |
Disable V.42bis/MNP5 data compression |
|
í &K1 |
Auto data compression |
|
&K2 |
Enable V.42bis/MNP5 data compression |
|
&K3 |
Disable MNP5 data compression |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Mn [cmds] |
|
Description: |
Selects communications mode |
|
Command |
Mode |
|
&M0 |
Normal mode enabled |
|
í &M4 |
ARQ and Normal modes enabled |
|
&M5 |
ARQ mode enabled |
|
AUTOMODE CONNECTION SPEED | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Nn [cmds] |
|
Description: |
Selects connection speed |
|
Command |
Mode |
|
í &N0 |
Enable Automode |
|
&N1 |
Set connection speed to 300bps |
|
&N2 |
Set connection speed to 1200bps |
|
&N3 |
Set connection speed to 2400bps |
|
&N4 |
Set connection speed to 4800bps |
|
&N5 |
Set connection speed to 7200bps |
|
&N6 |
Set connection speed to 9600bps |
|
&N7 |
Set connection speed to 12000bps |
|
&N8 |
Set connection speed to 14400bps |
|
&N9 |
Set connection speed to 16800bps |
|
&N10 |
Set connection speed to 19200bps |
|
&N11 |
Set connection speed to 21600bps |
|
&N12 |
Set connection speed to 24400bps |
|
&N13 |
Set connection speed to 26400bps |
|
&N14 |
Set connection speed to 28800bps |
|
&N15 |
Set connection speed to 31200bps |
|
&N16 |
Set connection speed to 33600bps |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
í &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe) |
|
RTS/CTS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Rn [cmds] |
|
Description: |
Selects RTS/CTS options |
|
Command |
Function |
|
&R0 |
Reserved |
|
&R1 |
Modem ignores the RTS signal |
|
í &R2 |
Enable RX hardware flow control (RTS) |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
í &S0 |
DSR forced high |
|
&S1 |
DSR off in command mode, on in on-line mode |
|
MINIMUM DCE CONNECTION SPEED | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &Un |
|
Description: |
Selects test options |
|
Command |
Function |
|
í &U0 |
Do not set minimum DCE connection speed |
|
&U1 |
Set connection speed to 300bps |
|
&U2 |
Set connection speed to 1200bps |
|
&U3 |
Set connection speed to 2400bps |
|
&U4 |
Set connection speed to 4800bps |
|
&U5 |
Set connection speed to 7200bps |
|
&U6 |
Set connection speed to 9600bps |
|
&U7 |
Set connection speed to 12000bps |
|
&U8 |
Set connection speed to 14400bps |
|
&U9 |
Set connection speed to 16800bps |
|
&U10 |
Set connection speed to 19200bps |
|
&U11 |
Set connection speed to 21600bps |
|
&U12 |
Set connection speed to 24400bps |
|
&U13 |
Set connection speed to 26400bps |
|
&U14 |
Set connection speed to 28800bps |
|
&U15 |
Set connection speed to 31200bps |
|
&U16 |
Set connection speed to 33600bps |
|
BREAK CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Yn [cmds] |
|
Description: |
Controls break |
|
Command |
Function |
|
í &Y0 |
Destructive break. Does not send break |
|
&Y1 |
Destructive break. Break expedited |
|
&Y2 |
Nondestructive break. Break expedited |
S(status) -REGISTERS
|
BIT-MAPPED REGISTER S13 | |
|
Type: |
Register |
|
Format |
AT [cmds] S13=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
DTR reset, ARQ 1.5K buffer DTR/reset, backspace autodial, +++ hangup |
|
BIT-MAPPED REGISTER S15 | |
|
Type: |
Register |
|
Format |
AT [cmds] S15=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
Disable V.42bis/MNP MNP incompatability |
|
INACTIVITY TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S19=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
1 minute |
|
Description: |
Sets the length of time inactivity timer waits before disconnecting |
|
BREAK LENGTH | |
|
Type: |
Register |
|
Format |
AT [cmds] S21=n [cmds] |
|
Default: |
10 |
|
Range: |
0-255 |
|
Unit: |
.01 second |
|
Description: |
ARQ break length |
|
FLOW CONTROL CHARACTER - XON | |
|
Type: |
Register |
|
Format: |
AT [cmds] S22=n [cmds] |
|
Default: |
17 |
|
Range: |
0-127 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XON |
|
FLOW CONTROL CHARACTER - XOFF | |
|
Type: |
Register |
|
Format: |
AT [cmds] S23=n [cmds] |
|
Default: |
19 |
|
Range: |
0-127 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XOFF |
|
BIT-MAPPED REGISTER S27 | |
|
Format |
AT [cmds] S27=n [cmds] |
|
Default: |
Unidentified |
|
Unit: |
Bit-mapped |
|
Description: |
V.21 @ 300bps, non-trellis encoding, disable 2400 Hz answer tone, 9600 result codes, disable V.32bis, enable V.23 |
|
BIT-MAPPED REGISTER S28 | |
|
Format |
AT [cmds] S28=n [cmds] |
|
Default: |
8 |
|
Range: |
0-255 |
|
Unit: |
0.1 second |
|
Description: |
Controls V.32 handshake length |
|
ANSWER MODE TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S29=n [cmds] |
|
Default: |
20 |
|
Range: |
0-255 |
|
Unit: |
.01 second |
|
Description: |
V.21 answer mode timer |
|
BIT-MAPPED REGISTER S32 | |
|
Type: |
Register |
|
Format: |
AT [cmds] S32=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
Disable V.FC, V.34, V.34bis, Enable V.8 |
|
BIT-MAPPED REGISTER S33 | |
|
Type: |
Register |
|
Format: |
AT [cmds] S33=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
Disable 2400, 2743, 2800, 3000, 3200, and 3429 symbol rates, call indicate, V.8 |
|
BIT-MAPPED REGISTER S34 | |
|
Type: |
Register |
|
Format: |
AT [cmds] S34=n [cmds] |
|
Unit: |
Bit-mapped |
|
Description: |
Disable 8S-2D, 16S-4D, 32S-4D maps |
