MAXTECH CORPORATION
RCI144ATI
|
Card Type |
Fax, Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Data Rate |
14.4Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
8-bit ISA |
|
Fax Class |
Class I |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
RJ-11 |
CN1 |
RJ-11 |
CN2 | |||
|
SERIAL PORT ADDRESS | ||
|
Setting |
JP1/E |
JP1/F |
|
í COM1 (3F8h) |
On |
On |
|
COM2 (2F8h) |
On |
Off |
|
COM3 (3E8h) |
Off |
On |
|
COM4 (2E8h) |
Off |
Off |
|
INTERRUPT | ||||
|
Setting |
JP1/A |
JP1/B |
JP1/C |
JP1/D |
|
2 |
Off |
Off |
Off |
On |
|
3 |
Off |
Off |
On |
Off |
|
í 4 |
Off |
On |
Off |
Off |
|
5 |
On |
Off |
Off |
Off |
Proprietary AT Command Set
|
BIT MAPPED REGISTERS | |
|
Register |
Default |
|
S14 |
138 |
|
S16 |
0 |
|
S21 |
4 |
|
S22 |
117 |
|
S23 |
55 |
|
S27 |
73 |
|
S28 |
0 |
|
S31 |
2 |
|
S39 |
3 |
|
S40 |
105 |
|
S41 |
3 |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Example: |
ATDT555-1212,,1234, |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Modifier |
Function |
|
P |
Pulse dialing enabled |
|
S=n |
Dial stored telephone number n. n=0-3 |
|
T |
Tone dialing enabled |
|
W |
Dialing resumed following dial tone detection |
|
, |
(Comma) Dialing paused for amount of time specified in S8 register |
|
@ |
Wait for quiet answer. |
|
! |
Flash function initiated. |
|
; |
(Semi-colon) Modem returned to command state after dialing. |
|
FLASH DIAL MODIFIER TIME | |
|
Type: |
Register |
|
Format |
AT [cmds] S29=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
.01 second |
|
Description: |
Time the modem will go on-hook upon receiving the ! dial modifier in dial string. |
|
FLOW CONTROL CHARACTER - XOFF | |
|
Type: |
Register |
|
Format: |
AT [cmds] S33=n [cmds] |
|
Default: |
19 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XOFF |
|
FLOW CONTROL CHARACTER - XON | |
|
Type: |
Register |
|
Format: |
AT [cmds] S32=n [cmds] |
|
Default: |
17 |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the character used to represent XON |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports product identification code |
|
I1 |
Reports factory ROM checksum |
|
I2 |
Reports internal memory test |
|
I3 |
Reports firmware ID |
|
I4 |
Reports reserved ID |
|
SLEEP TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S24=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
1 second |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. S24=0 will disable. |
|
INACTIVITY TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S30=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
.01 second |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating hang-up process. S30=0 will disable. |
|
TRANSMISSION LEVEL - FAX | |
|
Type: |
Register |
|
Format: |
AT [cmds] S92=n [cmds] |
|
Default: |
10 |
|
Range: |
0-15 |
|
Unit: |
-1 dBm |
|
Description: |
Sets the signal level for transmission while in fax mode |
|
TRANSMISSION LEVEL - PSTN | |
|
Type |
Register |
|
Format |
AT [cmds] S91=n [cmds] |
|
Default |
10 |
|
Range |
0-15 |
|
Unit |
-1 dBm |
|
Description |
Sets the signal level for transmission over switched phone lines |
