EXP COMPUTER, INC.
THINFAX 288C
|
Card Type |
Modem (synchronous/asynchronous) |
|
Chipset |
Unidentified |
|
Maximum Data Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC |
|
Fax Modulation |
ITU-T V.17, V.21CH2, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, MNP10, V.42, V.42bis |
|
Fax Class |
Class I & II |
|
Data Bus |
PCMCIA Type II |
53278
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, ‘comma’, A/ |
|
A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z |
|
&C, &D, &F, &G, &K, &L, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \G, \K, \N |
|
%C, %E, %L, %Q, %TT |
|
Special AT Commands |
|
#CID, :E, *H, -K, )M, @M, +MS, -Q |
|
S-Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25 |
|
S26, S27, S28, S29, S30, S31, S32, S33, S36, S38, S39, S40, S41, S46, S48, S82, S86, S91, S92 |
|
S95, S99, S201 |
Note: See MHI help file for complete information. |
|
UNIDENTIFIED COMMANDS | |
|
Command |
Default |
|
S37 |
0 |
|
S80 |
0 |
Proprietary AT Command Set
|
AUTOSYNC OPTIONS | ||
|
Type: |
Register | |
|
Format |
AT [cmds] S19=n [cmds] | |
|
Default: |
26 | |
|
Range: |
0 - 30 | |
|
Description: |
Controls autosync protocol, HDLC address detection, bit coding, and HDLC idle. | |
|
Bit |
Value |
Function |
|
0 |
0 |
Not used |
|
1 |
0 í 1 |
Binary synchronous protocol used. HDLC protocol used. |
|
2 |
í 01 |
HDLC address detect disabled. HDLC address detect enabled. |
|
3 |
0 í 1 |
NRZI bit coding used. NRZ bit coding used. |
|
4 |
0 í 1 |
HDLC idle sends MARK. HDLC idle sends FLAG or SYNC. |
|
AUTOSYNC HDLC ADDRESS | |
|
Type: |
Register |
|
Format: |
AT [cmds] S20=n [cmds] |
|
Default: |
0 |
|
Range: |
0-255 |
|
Unit: |
Unidentified |
|
Description: |
Sets the HDLC address and binary synchronous character. |
|
CELLULAR DRIVER DOWNLOAD | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] ^C2 [cmds] |
|
Description: |
Downloads a cellular phone driver. |
|
CELLULAR STATUS | |||||
|
Type: |
Immediate | ||||
|
Format: |
AT [cmds] ^T6 [cmds] | ||||
|
Default: |
Read-only | ||||
|
Range: |
0 - 191 | ||||
|
Description: |
Indicates the status of cellular phone. | ||||
|
Bit |
Value |
Function | |||
|
0 |
0 1 |
Cellular phone is not receiving a call. Cellular phone is receiving a call. | |||
|
1 |
0 1 |
Cellular phone is not in use. Cellular phone is in use. | |||
|
2 |
0 1 |
Cellular phone is not locked. Cellular phone is locked. | |||
|
3 |
0 1 |
Cellular service detected. Cellular service not detected. | |||
|
4 |
0 1 |
Cellular phone is powered off. Cellular phone is powered on. | |||
|
5 |
0 1 |
Cellular driver is initialized. Cellular driver is not initialized. | |||
|
6 |
0 |
Not used. | |||
|
7 |
0 1 |
Cellular cable not detected. Cellular cable detected. | |||
|
DISPLAY CELLULAR DRIVER INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] ^I [cmds] |
|
Description: |
Displays information about the current cellular driver. |
|
DISPLAY INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested about the modem. |
|
Command |
Function |
|
I0 |
Displays product identification code. |
|
I1 |
Displays ROM checksum. |
|
I2 |
Reports OK |
|
I3 |
Displays firmware model, revision, and interface type. |
|
I4 |
Displays OEM response. |
|
I5 |
Displays country code. |
|
I6 |
Displays data pump model. |
|
I7 |
Displays DAA code. |
|
REMOTE CONFIGURATION CHARACTER | |
|
Type: |
Register |
|
Format: |
AT [cmds] S202=n [cmds] |
|
Default: |
170 |
|
Range: |
0 - 255 |
|
Unit: |
1 ASCII character |
|
Description: |
Defines the character that, when sent four times within the guard time set by S12, will notify the remote modem that a remote configuration session has been requested. Values over 127 disables the remote configuration character. |