DIGICOM SYSTEMS
SCOUT PCMCIA 28.8 V.34
|
Card Type |
Fax, Modem |
|
Chip Set |
Unidentified |
|
Maximum Modem Rate |
28.8Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.22, V.22bis, V.32, V.32bis, V.34 |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I & II |
|
Data Bus |
PCMCIA |
54680
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, A/ |
|
A, B, C, E, H, L, 0, P, Q, M, V, W, Z |
|
&C, &F, &G, &L, &M, &R, &T, &W, &X, &Y, &Z |
|
Extended AT Commands |
|
\G, \J, \K, \X |
|
%A, %G |
|
-J |
|
"H, "O |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S16, S18, S25, S26, S27, S30 |
|
Note: See MHI Help file for full command documentation. |
PROPRIETARY AT COMMAND SET
|
AUTO-MODE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
|
Command |
Function |
|
N0 |
Auto-mode detection disabled |
|
í N1 |
Auto-mode detection enabled |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Qn [cmds] |
|
Description: |
Selects communications mode (same as &M) |
|
Command |
Mode |
|
&Q0 |
Asynchronous mode |
|
&Q1 |
Synchronous connect mode and asynchronous off-line command mode. |
|
&Q2 |
Synchronous connect mode and asynchronous off-line command mode and set DTR high. |
|
&Q3 |
Synchronous connect mode |
|
CONFIGURATION PROFILES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &V [cmds] |
|
Description: |
Displays active and stored configuration profiles |
|
Command |
Function |
|
&V0 |
View active file, stored profile 0, and phone numbers |
|
&V1 |
View active file, stored profile 1, and phone numbers |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
&S1 |
DSR high only while modem is handshaking or connected |
|
DATA TERMINAL READY (DTR) | |||||
|
Type: |
Configuration | ||||
|
Format: |
AT [cmds] &Dn [cmds] | ||||
|
Description: |
Selects modem response to DTR | ||||
Note: The action each variant of &D causes depends on the setting of &Q | |||||
|
&Q Setting |
&D0 |
&D1 |
&D2 |
&D3 | |
|
&Q0, &Q5, &Q6 |
Command 0 |
Command 1 |
Command 2 |
Command 3 | |
|
&Q1, &Q4 |
Command 0 |
Command 1 |
Command 2 |
Command 3 | |
|
&Q2, &Q3 |
Command 0 |
Command 1 |
Command 2 |
Command 2 | |
|
Command |
Function | ||||
|
Command 0 |
Modem does not respond to DTR | ||||
|
Command 1 |
Modem goes to command mode after DTR goes is off | ||||
|
Command 2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. | ||||
|
Command 3 |
Modem is initialized after DTR goes off | ||||
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DR |
Reserved |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go on-hook for time specified by S20 |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
DJ |
Modem performs MNP 10 link negotiation at the highest supported speed |
|
DK |
Power level adjustment during MNP link negotiation enabled |
|
D^ |
Calling tone transmission disabled |
|
D> |
Modem generates a grounding pulse if enabled by a country specific parameter |
|
ECHOPLEX VALIDITY | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Fn [cmds] |
|
Description: |
Selects whether commands sent while in data mode are echoed |
Note: Echoplex validity is a dummy command and not supported by this modem | |
|
Command |
Function |
|
F0 |
Returns error |
|
F1 |
Echoplex disabled |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables flow control options |
|
Command |
Function |
|
&K0 |
Flow control disabled |
|
&K3 |
RTS/CTS flow control enabled |
|
&K4 |
XON/XOFF flow control enabled |
|
&K5 |
Transparent XON/XOFF flow control enabled |
|
&K6 |
Unidirectional XON/XOFF flow control enabled |
|
JACK TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Jn [cmds] |
|
Description: |
Dummy command for backward compatibility |
|
Command |
Jack Type |
|
&J0 |
Returns OK |
|
&J1 |
Returns OK |
|
LONG SPACE DISCONNECT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Yn [cmds] |
|
Description: |
Dummy command for backward compatibility |
|
Command |
Function |
|
Y0 |
Reports OK |
|
Y1 |
Reports OK |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
í &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe) |
|
SELECT CALL PROGRESS RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Xn [cmds] |
|
Description: |
Enables selection of tone detection and associated result code format options |
|
Command |
Function |
|
X0 |
Displays CONNECT or 1 for all speeds |
|
X1 |
Displays connect messages according to ATW and AT/V commands. Busy tone detection disabled, dials blindly |
|
X2 |
Displays connect messages according to ATW and AT/V commands. Busy tone detection disabled, dial tone detection enabled |
|
X3 |
Displays connect messages according to ATW and AT/V commands. Busy tone detection enabled, dials blindly |
|
í X4 |
Displays connect messages according to ATW and AT/V commands. Busy tone detection enabled, sends all messages |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports four digit product code |
|
I1 |
Reports OK |
|
I2 |
Test and reports ROM checksum |
|
I3 |
Reports ROM components |
|
I4 |
Reports modem capabilities |
|
V.32 - AUTO-RETRAIN | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Bn [cmds] |
|
Description: |
Controls auto-retrain function if poor line quality is detected |
|
Command |
Function |
|
&B0 |
Auto-retrain enabled. Hang up if line quality is poor |
|
&B1 |
Auto-retrain enabled. Hang up if poor line quality persists for longer than threshold specified by register S37 |
|
&B2 |
Do not hang up or retrain. Accept any line |
EXTENDED AT COMMAND SET
|
COMPRESSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Cn [cmds] |
|
Description: |
Selects data compression |
|
Command |
Function |
|
%C0 |
Data compression disabled |
|
%C1 |
MNP5 enabled |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Direct mode enabled |
|
\N2 |
Reliable mode enabled |
|
í \N3 |
LAPM mode is enabled first, then MNP mode. Normal mode is selected if both fail |
|
\N4 |
LAPM mode is enabled first, then MNP mode. Modem hangs up if both fail |
|
FIRMWARE VERSION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] -Vn [cmds] |
|
Description: |
Display firmware version number |
|
FLOW CONTROL TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Qn [cmds] |
|
Description: |
Sets type of flow control used by modem |
|
Command |
Function |
|
\Q0 |
Flow control disabled |
|
\Q1 |
Bi-directional XON/XOFF flow control enabled |
|
\Q2 |
CTS flow control by DTE enabled |
|
\Q3 |
Bi-directional RTS/CTS flow control enabled |
|
INACTIVITY TIMER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Tn [cmds] |
|
Range: |
0-90 |
|
Unit: |
1 minute |
|
Description: |
Sets the length of time that the modem does not receive information before it disconnects. |
|
PROTOCOL RESULT CODES | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Vn [cmds] |
|
Description: |
Enables/disables protocol result codes |
|
Command |
Function |
|
\V0 |
Protocol result codes disabled |
|
\V1 |
Protocol result codes enabled |
|
V.42bis - DICTIONARY SIZE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] "Nn [cmds] |
|
Description: |
Select V.42 dictionary size |
|
Command |
Function |
|
"N0 |
Select 512 bytes |
|
"N1 |
Select 1024 bytes |
|
í "N2 |
Select 1536 bytes |
S(STATUS) -REGISTERS
|
BIT-MAPPED REGISTER S14 | ||
|
Format: |
AT [cmds] S14=n [cmds] | |
|
Range: |
0-174 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls echo, result codes and display, dial mode, and answer/originate mode. | |
|
Bit |
Value |
Function |
|
0 |
0 |
Not used |
|
1 |
0 í 1 |
Command echo disabled Command echo enabled |
|
2 |
í 01 |
Result codes enabled Result codes disabled |
|
3 |
0 í 1 |
Display result codes in numeric format Display result codes in verbose format |
|
4 |
0 |
Not used |
|
5 |
0 í 1 |
Tone dial enabled Pulse dial enabled |
|
6 |
0 |
Not used |
|
7 |
í 0 1 |
Answer mode enabled Originate mode enabled |
|
BIT-MAPPED REGISTER S19 | ||
|
Format: |
AT [cmds] S19=n [cmds] | |
|
Unit: |
Bit-mapped | |
|
Description: |
Autosync protocol support mode | |
|
Bit |
Value |
Function |
|
0 |
0 |
Reserved |
|
1 |
0 í 1 |
Bisync protocol HDLC protocol |
|
2 |
í 01 |
Address detector disabled Address detector enabled |
|
3 |
0 í 1 |
NRZI bit coding NRZ bit coding |
|
4 |
0 í 1 |
Mark idle Flag idle |
|
BIT-MAPPED REGISTER S21 | ||
|
Format |
AT [cmds] S21=n [cmds] | |
|
Range: |
0-253 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Selects CTS/DCD/DSR signals, and low DTR action | |
|
Bit |
Value |
Function |
|
0,1 |
0 |
Reserved |
|
2 |
0 1 |
CTS follows RTS CTS forced high |
|
4, 3 |
00 01 10 11 |
DTR signal ignored Modem goes to command mode on low DTR Modem disconnects on low DTR; Auto-Answer is disabled. Modem is initialized on low DTR |
|
5 |
0 1 |
DCD forced high DCD normal |
|
6 |
0 1 |
DSR forced high DSR normal |
|
7 |
0 |
Reserved |
|
BIT-MAPPED REGISTER S23 | ||
|
Format |
AT [cmds] S23=n [cmds] | |
|
Range: |
0-189 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Grants/denies remote digital loopback, controls DTE rate and parity, and sets guard tone. | |
|
Bit |
Value |
Function |
|
0 |
0 í 1 |
Remote digital loopback denied Remote digital loopback allowed |
|
3 - 1 |
0 |
Reserved |
|
5, 4 |
00 01 10 11 |
Parity even Space Parity Parity odd Mark or No Parity |
|
7, 6 |
00 01 10 |
Guard tone disabled Guard tone 550Hz enabled Guard tone 1800Hz enabled |
|
BIT-MAPPED REGISTER S31 | |||
|
Format: |
AT [cmds] S31=n [cmds] | ||
|
Range: |
0-10 | ||
|
Description: |
Select automode and extended result code format. | ||
|
Bit |
Value |
Function | |
|
0 |
0 |
Not used | |
|
1 |
0 1 |
Auto-mode detection disabled Auto-mode detection enabled | |
|
3, 2 |
00 01 10 |
Enables CONNECT result codes to report DTE speed Full reporting of CONNECT result codes Enables CONNECT result codes to report DCE speed | |
|
BIT-MAPPED REGISTER S40 | ||
|
Format |
AT [cmds] S40=n [cmds] | |
|
Range: |
0-255 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls automode and V.42 detection | |
|
Bit |
Value |
Function |
|
0 |
0 1 |
Automode disabled Automode enabled |
|
1-5 |
0 |
Reserved |
|
6 |
0 1 |
V.42 detection disabled V.42 detection enabled |
|
AUTOMATIC-FALLBACK FOR MNP NEGOTIATION | |
|
Type: |
Register |
|
Format |
AT [cmds] S43=n [cmds] |
|
Range: |
1-127 |
|
Unit: |
ASCII |
|
Description: |
Determines automatic fallback character for MNP negotiation |
|
BIT-MAPPED REGISTER S44 | ||
|
Format |
AT [cmds] S44=n [cmds] | |
|
Range: |
0-255 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls data compression mode | |
|
Bit |
Value |
Function |
|
0 |
0 1 |
V.42bis disabled V.42bis enabled |
|
1,2 |
00 01 10 11 |
V.42bis disabled V.42bis when transmitting enabled V.42bis when receiving enabled V.42bis when transmitting/receiving enabled |
|
3 |
0 |
Reserved |
|
4 |
0 1 |
Auto-fallback/fall-forward disabled Auto-fallback/fall-forward enabled |
|
5-7 |
0 |
Reserved |
|
AUTORELIABLE BUFFER | |
|
Type: |
Register |
|
Format |
AT [cmds] S48=n [cmds] |
|
Range: |
0-2 |
|
Unit: |
ASCII |
|
Description: |
Controls autoreliable buffer |
|
BIT-MAPPED REGISTER S51 | ||
|
Format |
AT [cmds] S51=n [cmds] | |
|
Range: |
0-255 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls data/fax DTE flow control | |
|
Bit |
Value |
Function |
|
0-1 |
00 01 10 11 |
Flow control disabled RTS to CTS flow control enabled XON/XOFF flow control enabled RTS/CTS flow control enabled |
|
2-3 |
0 |
Reserved |
|
4 |
0 1 |
Flow control disabled Flow control enabled |
|
5 |
0 1 |
Serial speed locked Serial speed follows connect speed |
|
6,7 |
0 1 |
XON/XOFF signals trapped by local modem XON/XOFF signals passed through local modem |
|
BIT-MAPPED REGISTER S54 | |
|
Format |
AT [cmds] S54=n [cmds] |
|
Range: |
0-255 |
|
Unit: |
ASCII |
|
Description: |
Unidentified |
|
BTLZ OPTIONS | |
|
Type: |
Register |
|
Format |
AT [cmds] S58=n [cmds] |
|
Range: |
6-64 |
|
Unit: |
ASCII |
|
Description: |
Sets BTLZ string length. Default=32 |
|
BREAK OPTION | |
|
Type: |
Register |
|
Format |
AT [cmds] S52=n [cmds] |
|
Range: |
0-5 |
|
Unit: |
Unidentified |
|
Description: |
Controls break options. Default=5 |
|
CONNECT MESSAGE DISPLAY | |
|
Format |
AT [cmds] S41=n [cmds] |
|
Range: |
0-2 |
|
Unit: |
ASCII |
|
Description: |
Control display of connect message |
|
DATA/FAX MODE | |
|
Format |
AT [cmds] S50=n [cmds] |
|
Range: |
0-1 |
|
Unit: |
ASCII |
|
Description: |
Control data/fax mode options |
|
DCE LINE SPEED | |
|
Type: |
Register |
|
Format |
AT [cmds] S37=n [cmds] |
|
Description: |
Sets the maximum allowable data exchange rate attempted during handshake process. |
|
DTE RATE SELECTION | |
|
Type: |
Register |
|
Format |
AT [cmds] S72=n [cmds] |
|
Range: |
0-18 |
|
Unit: |
ASCII |
|
Description: |
Selects DTE rate during data transfer |
|
DTE RATE STATUS | |
|
Type: |
Register |
|
Format |
AT [cmds] S62=n [cmds] |
|
Range: |
0-17 |
|
Unit: |
ASCII |
|
Description: |
Determines DTE rate status. Default=16 |
|
EEPROM CHECKSUM | |
|
Type: |
Register |
|
Format |
AT [cmds] S99=n [cmds] |
|
Range: |
Unidentified |
|
Unit: |
ASCII |
|
Description: |
Sets EEPROM checksum |
|
MAXIMUM BLOCK SIZE | |
|
Type: |
Register |
|
Format |
AT [cmds] S49=n [cmds] |
|
Range: |
63-255 |
|
Unit: |
ASCII |
|
Description: |
Sets the maximum block size. Default=255 |
|
MNP5 ERROR CORRECTION | |
|
Type: |
Register |
|
Format |
AT [cmds] S59=n [cmds] |
|
Range: |
0-1 |
|
Unit: |
ASCII |
|
Description: |
Sets MNP5 error correction. Default=1 |
|
MODEM OPERATING MODE | |
|
Type: |
Register |
|
Format |
AT [cmds] S53=n [cmds] |
|
Range: |
0-4 |
|
Unit: |
ASCII |
|
Description: |
Selects modem operating mode |
|
POWER-UP PROFILE | |
|
Type: |
Register |
|
Format |
AT [cmds] S98=n [cmds] |
|
Range: |
Unidentified |
|
Unit: |
ASCII |
|
Description: |
Sets power-up profile number |
|
ROUND TRIP DELAY | |
|
Type: |
Register |
|
Format |
AT [cmds] S65=n [cmds] |
|
Range: |
Unidentified |
|
Unit: |
1sec |
|
Description: |
Sets round trip time delay |
|
SLEEP TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S46=n [cmds] |
|
Range: |
0-255 |
|
Unit: |
1sec |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. |
|
SLEEP TIMER/PCMCIA | |
|
Type: |
Register |
|
Format |
AT [cmds] S47=n [cmds] |
|
Range: |
0-255 |
|
Unit: |
1sec |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. |
|
V.32 RETRAIN | |
|
Type: |
Register |
|
Format |
AT [cmds] S42=n [cmds] |
|
Range: |
0-2 |
|
Unit: |
ASCII |
|
Description: |
Controls V.32 retrain |
|
V.42bis DICTIONARY SIZE | |
|
Type: |
Register |
|
Format |
AT [cmds] S57=n [cmds] |
|
Range: |
0-2 |
|
Unit: |
Unidentified |
|
Description: |
Sets the maximum V.42bis dictionary size. Default=2 |