Card Type	Modem(synchronous/asynchronous)
Chip Set	Unidentified
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	External
Fax Class	Class II
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation Protocol	ITU-T V.17, V.21CH2, V.27ter, V.29
Error Correction/Compression	MNP5, V.42bis

CONNECTIONS
Function	Label		Function		Label
Line out		CN1		Power switch		SW1
Line in/leased line		CN2		LCD panel lock		SW2
RS-232/422		CN3		Voice/data		SW3
DC power		CN4		LCD panel navigation		NAV
Volume		R1

DIAGNOSTIC LED(S)
LED	Color	Status	Condition
MR	Yellow	On	Power is on
MR	Yellow	Off	Power is off
TR	Yellow	On	DTR signal is high
TR	Yellow	Off	DTR signal is low
RTS	Yellow	On	RTS signal is high
RTS	Yellow	Off	RTS signal is low
CTS	Yellow	On	CTS signal is high
CTS	Yellow	Off	CTS signal is low
AA	Yellow	On	Auto-answer enabled
AA	Yellow	Off	Auto-answer disabled
AA	Yellow	Blinking	Phone is ringing
RL	Yellow	On	Error correction enabled
RL	Yellow	Off	Error correction disabled
RL	Yellow	Blinking	Error detected
RD	Yellow	Blinking	Modem is receiving data
RD	Yellow	Off	Modem is not receiving data
SD	Yellow	Blinking	Modem is transmitting data
SD	Yellow	Off	Modem is not transmitting data
CD	Yellow	On	Carrier signal detected
CD	Yellow	Off	Carrier signal not detected
OH	Yellow	On	Modem is off-hook
OH	Yellow	Off	Modem is on-hook

ANSWER TONE DETECTION
Type:	Configuration
Format:	AT [cmds] %In [cmds]
Description:	Controls answer tone detection
Command		Function
%I0		Answer tone detection enabled
%I1		Answer tone detection disabled

AUTO REDIAL INTERVAL TIMES
Type	Register
Format	AT [cmds] S19=n [cmds]
Default	2
Range	0-255
Unit	Unidentified
Description	Unidentified

AUTO-RELIABLE FALLBACK CHARACTER
Type:	Configuration
Format:	AT [cmds] %An [cmds]
Default:	0
Range:	0-127
Unit:	ASCII
Description:	Sets the character used as the auto-reliable fallback character. %A0 will disable this function

AUTO-RELIABLE TIME BUFFER CONFIGURATION
Type:	Configuration
Format:	AT [cmds] \Cn [cmds]
Description:	Controls the handling of incoming data during auto-reliable time period
Command	Function
í \CO	Data is discarded
\C1	Data is buffered
\C2	Data is discarded, resets to \C1 on receipt of autoreliable fallback character

AUTO-RETRAIN
Type:	Configuration
Format:	AT %En
Description:	Selects auto-retrain mode
Command	Function
%E0	Auto-retrain disabled
%E1	Three auto-retrains attempted then hang up for 2400bps and above enabled
í %E2	Three auto-retrains attempted then hang up for 2400bps and above enabled

BIT-MAPPED REGISTER S14
Format		AT [cmds] S14=n [cmds]
Default:		136
Range:		0-254
Unit:		Bit-mapped
Description:		Controls echo, result codes, result code display, dumb mode, dial mode, dumb modem and answer/originate mode
Bit	Value	Function
0	0	Not used
1	í 0 1	Command echo disabled Command echo enabled
2	í 0 1	Result codes enabled Result codes disabled
3	0 í 1	Display result codes in numeric format Display result codes in verbose format
4	í 0 1	Smart mode Dumb mode
5	í 0 1	Tone dial enabled Pulse dial enabled
6	í 0 1	Smart modem Dumb modem
7	0 í 1	Answer mode enabled Originate mode enabled

BIT-MAPPED REGISTER S21
Format:			AT [cmds] S20=n [cmds]
Default:			176
Range:			0-187
Description:			Controls jack type, DSR, DTR, DCD and disconnect options
Bit	Value			Function
0	í 0 1			RJ-11/41S/45S RJ12-12/13
1		í 0 1			DSR forced high DSR normal
2		0			Not used
4, 3		00 01 í 10 11			Ignore DTR Go to command mode on low DTR Hang up on low DTR Initialize on low DTR
5		0 í 1			DCD forced high Normal operation
7, 6		00 01 í 10			Special disconnect disabled Long space disconnect enabled Clear down disconnect enabled

BIT-MAPPED REGISTER S22
Format		AT [cmds] S22=n [cmds]
Default:		118
Range:		0 - 255
Unit:		Bit-mapped.
Description:		Controls volume and speaker settings, result codes, and make/break pulse ratio
Bit	Value	Function
1, 0	00 01 í 10 11	Lowest volume setting Low volume setting Medium volume setting Highest volume setting
3, 2	00 í 01 10 11	Speaker disabled Speaker enabled until carrier signal detected Speaker enabled Speaker enabled until carrier signal detected, but disable during dialing
6, 5 ,4	000 001 010 011 í 100	Numeric result codes enabled Verbose result codes enabled Dialtone detection enabled Busy tone detection enabled Busy and dialtone detection enabled
7	í 0 1	39/61ms at 10pps (North America) 33/67ms at 10pps (Europe)

BIT-MAPPED REGISTER S24
Format:			AT [cmds] S24=n [cmds]
Default:			0
Range:			0-7
Description:			Controls V.25bis options
Bit	Value			Function
0	í 0 1			V.25bis disabled V.25bis enabled
1		í 0 1			V.25bis asynchronous enabled V.25bis synchronous enabled
2		í 0 1			V.25bis HDLC enabled V.25bis bisynchronous enabled

BIT-MAPPED REGISTER S27
Format:			AT [cmds] S27=n [cmds]
Default:			0
Range:			0-236
Description:			Controls synchronous mode, pulse dial speed, clock source, and data protocol
Bit	Value			Function
2, 1, 0	í 000 001 010 011 100			Asynchronous operation Synchronous mode 1 operation Synchronous mode 2 operation Synchronous mode 3 operation Asynchronous dial
3		í 0 1			Standard pulse dial enabled Fast pulse dial enabled
5, 4		í 00 01 10			Local DCE transmit clock enabled Local DTE transmit clock enabled Remote DCE transmit enabled
7, 6		í 00 01 10 11			V.21, V.22, V.32 enabled Bell 103A/212A V.23 back channel V.23 main channel

BIT-MAPPED REGISTER S29
Format:			AT [cmds] S29=n [cmds]
Default:			3
Range:			31
Description:			Controls data bits, parity and stop bits
Bit	Value			Function
1, 0	00 01 10 í 11			5 data bits 6 data bits 7 data bits 8 data bits
3, 2		í 00 01 10 11			No parity Space parity Even parity Odd parity
4		í 0 1			1 stop bit 2 stop bits

BIT-MAPPED REGISTER S32
Format:			AT [cmds] S32=n [cmds]
Default:			17
Range:			0-191
Description:			Controls ring, call back security, hardware data security, message working bit, V.32 forward/backward link, &Z/@Z working bit and line used
Bit	Value			Function
0	0 í 1			Ring disabled Ring enabled
1		í 0 1			Call back security disabled Call back security enabled
2		í 0 1			Hardware data security disabled Hardware data security enabled
3		í 0 1			Open message working bit Close message working bit
4		0 í 1			V.32 forward/backward link disabled V.32 forward/backward link enabled
5		í 0 1			&Z working bit enabled @Z working bit enabled
7, 6		í 00 01 10			Switched line enabled 2 wire leased line enabled 4 wire leased line enabled

BIT-MAPPED REGISTER S34
Format:			AT [cmds] S34=n [cmds]
Default:			0
Range:			0-63
Description:			Controls V.32 TCM/QAM, DTR dump recognition, RLSD level, asynchronous and soft reset
Bit	Value			Function
0	í 0 1			Enable trellis code modulation Enable quadratic amplitude modulation
1		í 0 1			Recognize DTR dump in handshaking Ignore DTR dump in handshaking
3, 2		í 00 01 10 11			RLSD on at, -43dbm off at -48dbm RLSD on at, -33dbm off at -38dbm RLSD on at, -26dbm off at -31dbm RLSD on at, -16dbm off at -21dbm
5, 4		í 00 01 10			Normal AT&F ATZ Quick ATZ.2 Quick AT&F ATZ

BIT-MAPPED REGISTER S35
Format:			AT [cmds] S35=n [cmds]
Default:			15
Range:			0-232
Description:			Controls Power on auto dial
Bit	Value			Function
3, 2, 1, 0	0000 í 1000			STN for power on auto dial Power on auto dial disabled
5, 4		í 00 01 10			Restore all disabled Switched line simulates leased line enabled Switched line back up enabled
6		í 0 1			Single phone system enabled Multiple phone systems enabled
7		í 0 1			Disconnect reset disabled Disconnect reset enabled

BIT-MAPPED REGISTER S39
Format:			AT [cmds] S39=n [cmds]
Default:			153
Range:			0-253
Description:			Controls compression, auto retrain answer tone check, compromise equalizer and detect phase
Bit	Value			Function
0	0 í 1			Data compression disabled Data compression enabled
2, 1		00 í 01 10			Auto retrain disabled Auto retrain on same speed Auto retrain with speed change
4, 3		00 01 10 í 11			Disabled Transmit only Receive only Transmit and receive
5		í 0 1			Answer tone check enabled Answer tone check disabled
6		í 0 1			Compromise equalizer enabled Compromise equalizer disabled
7		0 í 1			Detect phase disabled Detect phase enabled

BIT-MAPPED REGISTER S40
Format:			AT [cmds] S40=n [cmds]
Default:			0
Range:			0-33
Description:			Controls remote access and remote access security
Bit	Value			Function
0	í 0 1			Remote access disabled Remote access enabled
4, 3, 2, 1		0000			Not used
5		í 0 1			Remote access security disabled Remote access security enabled

BIT-MAPPED REGISTER S43
Format:			AT [cmds] S43=n [cmds]
Default:			19
Range:			0-155
Description:			Controls MNP block size, dictionary size and data buffer
Bit	Value			Function
1, 0	00 01 10 í 11			Maximum MNP block size 64 characters Maximum MNP block size 128 characters Maximum MNP block size 192 characters Maximum MNP block size 256 characters
2		0			Not used
4, 3		00 01 í 10 11			Maximum dictionary size 512 entries Maximum dictionary size 1024 entries Maximum dictionary size 2048 entries Maximum dictionary size 4048 entries
5		0			Not used
7, 6		í 00 01 10			Disable data buffer Set buffer to 4 seconds, 200 characters or SYN character detected then switch to normal connection Data buffer disabled, switch to normal connection

BIT-MAPPED REGISTER S44
Format:			AT [cmds] S44=n [cmds]
Default:			0
Range:			140
Description:			Controls echo, flow control and serial port speed.
Bit	Value			Function
2	í 0 1			On line data echo disabled On line data echo enabled
3		í 0 1			Modem port flow control disabled Modem port flow control enabled
6, 5, 4		000			Not used
7		í 0 1			Serial port speed locked Serial port speed follows connection speed

BIT-MAPPED REGISTER S45
Format:			AT [cmds] S45=n [cmds]
Default:			101
Range:			253
Description:			Controls break control, link type, DTE speed and mode
Bit	Value			Function
2, 1, 0	000 001 010 011 100 í 101			Enter command mode, do not send break Clear buffer, send break immediately Enter command mode, do not send break Do not clear buffer, send break immediately Enter command mode, do not send break Send break with transmitted data
3		í 0 1			Stream link enabled Block link enabled
4		í 0 1			DTE speed follows connect speed DTE speed locked
7, 6, 5		000 001 010 í 011 100 101 110 111			Normal mode Direct mode MNP mode Auto reliable mode LAPM mode LAPM with fallback to normal mode LAPM with fallback to MNP mode MNP with fallback to normal mode

BIT-MAPPED REGISTER S46
Format:			AT [cmds] S46=n [cmds]
Default:			75
Range:			0-238
Description:			Controls flow control, ring indicate and result codes
Bit	Value			Function
2, 1, 0	000 001 010 í 011 100 101 110			Flow control disabled XON/XOFF flow control enabled Unidirectional hardware flow control enabled Bidirectional hardware flow control enabled Unidirectional XON/XOFF flow control enabled CTS low until connect, then CTS unidirectional flow control enabled CTS low until connect, then RTS/CTS flow control enabled
3		0 í 1			Ring indicate after handshaking enabled Ring indicate after handshaking disabled
6, 5, 4		000 001 010 011 í 100 101 110			V.42/MNP result code disabled V.42/MNP4 and DTE speed result codes enabled V.42/MNP4 and DCE speed result codes enabled V.42bis/MNP5 and DTE speed result codes enabled V.42bis/MNP5 and DCE speed result codes enabled V.42bis/MNP5 and DTE debug codes enabled V.42bis/MNP5 and DCE debug codes enabled
7		í 0 1			Flow control character trapped Flow control character passed through

BIT-MAPPED REGISTER S53
Format:			AT [cmds] S53=n [cmds]
Default:			56
Range:			0-56
Description:			Controls ring indicate reset timer, V.25 calling tone and T30 calling tone
Bit	Value			Function
3, 2, 1, 0	í 1000			Ring indicate reset timer
4		0 í 1			V.25 calling tone disabled V.25 calling tone enabled
5		0 í 1			T30 calling tone disabled T30 calling tone enabled

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \Bn [cmds]
Default:	3
Range:	0-9
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:			Configuration
Format:			AT [cmds] \Kn [cmds]
Description:			Configures action of break signal
Command	Break from DTE
\K0		Online command mode enabled, send no break to remote modem
\K1		Break sent to remote modem and buffers cleared
\K2		Online command mode enabled, send no break to remote modem
\K3		Send break to remote modem immediately
\K4		Online command mode enabled, send no break to remote modem
\K5		Send break with transmitted data

CALL BACK DELAY TIMER
Type	Register
Format	AT [cmds] S31=n [cmds]
Default	10
Range	0-255
Unit	1 second
Description	Controls call back delay

CALLBACK NUMBER
Type	Configuration
Format	AT [cmds] @Zn=xxx [cmds]
Default	None
Description	Stores numbers to be called back during callback operation. N is a memory location from 0-9 and xxx is a combination of the number and up to 49 dial modifiers.

CALLBACK PASSWORD
Type	Configuration
Format	AT [cmds] @Wn=xxxxxxxxxx [cmds]
Default	None
Range	A-Z, a-z,0-9
Unit	ASCII string
Description	Stores callback password (n is password and xxxxxxxxxx is up to ten characters)

CALLBACK SECURITY
Type:	Configuration
Format:	AT [cmds] @An [cmds]
Description:	Modem returns call to previously stored number
Command		Function
í @A0		Callback security disabled
@A1		Callback security enabled

CALL BACK SECURITY DELAY
Type	Configuration
Format	AT [cmds] @Dn [cmds]
Default	30
Range	1-255
Unit	1 second
Description	Sets length of wait before dialing stored callback security phone number

CARRIER DETECT TIMER
Type	Register
Format	AT [cmds] S17=n [cmds]
Default	10
Range	0-255
Unit	Unidentified
Description	Unidentified

CLOSING MESSAGE
Type	Configuration
Format	AT [cmds] @Gxxx [cmds]
Default	THANK YOU! YOU WILL BE CALLED BACK!
Range	Up to 60 characters
Unit	ASCII
Description	Stores a closing message

CONNECTION PASSWORD SECURITY
Type:	Configuration
Format:	AT [cmds] @En [cmds]
Description:	Requires correct password to be included in dial command string
Command		Function
í @E0		Password security disabled
@E1		Password security enabled

COMPRESSION
Type:	Configuration
Format:	AT %Cn
Description:	Selects data compression
Command	Function
%C0	Data compression disabled
í %C1	MNP5 and V.42bis enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \Nn [cmds]
Description:	Sets connect mode
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	MNP reliable mode only enabled
í \N3	V.42 and MNP modes enabled
\N4	V.42bis and V.42 modes enabled

CONNECTION PASSWORD
Type	Configuration
Format	AT [cmds] @Pxxxxxxxxx [cmds]
Default	None
Range	A-Z,a-z,0-9,*,#
Unit	ASCII string
Description	Stores password required by command string password security option of up to nine characters

CONNECTION SPEED UPPER LIMIT
Type:	Immediate
Format:	AT [cmds] %Bn [cmds]
Description:	Selects the current DCE speed.
Command	Function
í %B0	Line speed sets maximum serial port speed
%B300	300bps
%B600	600bps
%B1200	1200bps
%B2400	2400bps
%B4800	4800bps
%B7200	7200bps
%B9600	9600bps
%B12000	12.0Kbps
%B16800	16.8Kbps
%B14400	14.4Kbps
%B19200	19.2Kbps
%B21600	21.6Kbps
%B24000	24.0Kbps
%B26400	26.4Kbps
%B28800	28.8Kbps

DIAL TONE DETECT
Type:	Configuration
Format:	AT [cmds] W [cmds]
Description:	Requires a continuous three second dial tone before dialing

DISPLAY CALLBACK SETTINGS
Type:	Immediate
Format:	AT [cmds] @Vn [cmds]
Description:	Displays passwords, messages and phone numbers stored in memory
Command		Function
@V0		Display stored callback security passwords
@V1		Display stored callback security phone numbers
@V2		Display opening and closing messages

DISPLAY PASSWORDS
Type:	Immediate
Format:	AT [cmds] @Fn [cmds]
Description:	Displays callback security and remote access passwords

DTR DELAY
Type	Register
Format	AT [cmds] S25=n [cmds]
Default	5
Range	0-255
Unit	1 second
Description	Sets length of time modem ignores DTR change

DUMB MODE
Type:	Configuration
Format:	AT [cmds] @In [cmds]
Description:	Controls smart and dumb modes
Command		Function
í @I0		Smart mode
@I1		Dumb mode

FLOW CONTROL TYPE
Type:	Configuration
Format:	AT [cmds] \Qn [cmds]
Description:	Sets type of flow control used by modem
Command	Function
\Q0	Flow control disabled
\Q1	XON/XOFF flow control enabled
\Q2	CTS flow control to DTE enabled
í \Q3	RTS/CTS flow control enabled

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \Gn [cmds]
Description:	Selects modem port flow control
Command	Function
í \G0	Flow control disabled
\G1	Flow control enabled

HANG UP DELAY
Type	Register
Format	AT [cmds] S38=n [cmds]
Default	0
Range	0-255
Unit	Unidentified
Description	Sets time before forced hang up, n=255 disables

INACTIVITY TIMER
Type:	Configuration
Format:	AT [cmds] \Tn [cmds]
Default:	0
Range:	0-255
Unit:	1 minute
Description:	Sets the length of time that the modem does not receive information before it disconnects

INACTIVITY TIMER
Type	Register
Format	AT [cmds] S47=n [cmds]
Default	0
Range	0-255
Unit	Unidentified
Description	Sets time modem waits before disconnecting

LEASED LINE DIALUP BACKUP TIMES
Type:	Register
Format:	AT [cmds] S13=n [cmds]
Default:	0
Range:	0-255
Unit:	Unidentified
Description:	After leased line failure, modem attempts to reconnect after specified delay

LEASED LINE DIALUP BACKUP TIMER
Type	Register
Format	AT [cmds] S15=n [cmds]
Default	5
Range	0-255
Unit	Unidentified
Description	Unidentified

LEASED LINE RETRY
Type	Configuration
Format	AT [cmds] -Bn [cmds]
Range	Unidentified
Unit	Retries
Description	Controls the number of times a leased line connection is attempted

LINE SIGNAL LEVEL
Type:	Immediate
Format:	AT [cmds] %L [cmds]
Description:	Returns received line signal level

LEASED LINE TRANSMIT LEVEL
Type	Register
Format	AT [cmds] S51=n [cmds]
Default	10
Range	0-31
Unit	Unidentified
Description	Sets leased line transmit level

LINE TYPE
Type:	Configuration
Format:	AT [cmds] @Yn [cmds]
Description:	Selects line type
Command		Function
í @Y0		Switched line operation
@Y1		Switched line operation emulates leased line operation
@Y2		Leased line with switched line backup

LOCK DCE
Type:	Configuration
Format:	AT [cmds] %Hn [cmds]
Description:	Controls DCE speed
Command		Function
%H0		DCE speed not locked
%H1		DCE speed locked

LOCK SERIAL PORT
Type:	Configuration
Format:	AT [cmds] \Jn [cmds]
Description:	Sets operation of serial port speed
Command	Function
í \J0	Serial speed locked
\J1	Serial speed follows connect speed

MAXIMUM BLOCK SIZE FOR TRANSMISSION
Type:	Configuration
Format:	AT [cmds] \An [cmds]
Description:	Sets the maximum transmittable block size
Command	Function
\A0	MNP block size is 64 characters
\A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
í \A3	MNP block size is 256 characters

OPENING MESSAGE
Type	Configuration
Format	AT [cmds] @Oxxx [cmds]
Default	PLEASE ENTER CALL BACK PASSWORD
Range	Up to 60 characters
Unit	ASCII string
Description	Stores an opening message

PROTOCOL
Type:	Configuration
Format:	AT [cmds] -Vn [cmds]
Description:	Controls protocol used
Command		Function
-V0		V.34 auto
-V1		V.FC auto
-V3		V.32bis auto
-V4		V.34/V.FC/V.32bis
-V5		V.34 only
-V6		V.FC only
-V7		V.32bis only

PROTOCOL
Type:	Register
Format:	AT [cmds] S54=n [cmds]
Description:	Controls protocol used
Command		Function
í S54=0		V.34 auto mode
S54=1		V.FC auto mode
S54=3		V.32bis auto mode
S54=4		V.34, V.FC and V.32bis
S54=5		V.FC and V.32bis
S54=6		V.34 only
S54=7		V.FC only
S54=8		V.32bis only

REDIAL
Type	Configuration
Format	AT [cmds] N=n [cmds]
Default	0
Range	0-15
Unit	Redials
Description	Sets number of redials attempted if busy signal received

REDIAL INTERVAL
Type	Configuration
Format	AT [cmds] N5=n [cmds]
Default	1
Range	0-255
Unit	2 seconds
Description	Controls time between redials

REDIAL LIMIT
Type	Register
Format	AT [cmds] S49=n [cmds]
Default	15
Range	Unidentified
Unit	Unidentified
Description	Sets maximum number of redials

REDIAL ORDER
Type	Configuration
Format	AT [cmds] -Z=nnn [cmds]
Unit	Phone number memory location
Description	Controls order in which stored numbers are dialed -Z? displays order

REMOTE ACCESS
Type:	Configuration
Format:	AT [cmds] *En [cmds]
Description:	Controls remote access operation
Command		Function
í *E0		Remote access disabled
*E1		Remote access enabled

REMOTE ACCESS ATTENTION CHARACTER
Type	Register
Format	AT [cmds] S41=n [cmds]
Default	42
Range	0-255
Unit	ASCII
Description	Selects the remote access attention character

REMOTE ACCESS PASSWORD
Type	Configuration
Format	AT [cmds] *Pxxxxxxxxx
Default	None
Range	Up to nine characters
Unit	ASCII printable characters
Description	Stores remote access password

REPORT SIGNAL QUALITY
Type:	Immediate
Format:	AT [cmds] %Q [cmds]
Description:	Reports signal quality

RESULT CODE FORMAT
Type:	Configuration
Format:	AT [cmds] \Vn [cmds]
Description:	Selects which result codes are displayed
Command		Function
\V0		Connect speed result codes enabled
\V1		Connect speed and V.42/MNP result codes enabled
\V2		Connect speed, V.42/MNP and data compression result codes enabled
\V3		Connect speed, V.42/MNP and data compression result codes enabled
\V4		Connect speed, V.42/MNP and data compression result codes enabled

RINGER
Type:	Configuration
Format:	AT [cmds] @Bn [cmds]
Description:	Controls ring signal passthrough to modem speaker
Command		Function
@B0		Ringer disabled
í @B1		Ringer enabled

RTS TO CTS DELAY
Type	Register
Format	AT [cmds] S26=n [cmds]
Default	0
Range	0-255
Unit	.1 second
Description	Sets delay after receipt of RTS signal until CTS forced high

SWITCHED LINE TRANSMIT LEVEL
Type	Register
Format	AT [cmds] S50=n [cmds]
Default	10
Range	0-15
Unit	Unidentified
Description	Sets switched line transmit level

SERIAL PORT
Format:			AT [cmds] S28=n [cmds]
Default:			113
Range:			0-243
Description:			Controls serial port options, parity and data bits
Bit	Value			Function
4, 3, 2, 1, 0	00000 00001 00010 00011 00100 00101 00110 00111 01000 01001 01010 01011 01100 01101 01110 01111 10000 í10001 10010 10011			Lock serial port at 75bps Lock serial port at 110bps Lock serial port at 300bps Lock serial port at 600bps Lock serial port at 1200bps Lock serial port at 2400bps Lock serial port at 4800bps Lock serial port at 7200bps Lock serial port at 9600bps Lock serial port at 12.0Kbps Lock serial port at 14.4Kbps Lock serial port at 16.8Kbps Lock serial port at 19.2Kbps Lock serial port at 21.6Kbps Lock serial port at 24.0Kbps Lock serial port at 26.4Kbps Lock serial port at 28.8Kbps Lock serial port at 38.4Kbps Lock serial port at 57.6Kbps Lock serial port at 11.52Kbps
6, 5		00 01 10 í 11			Even parity Space parity Odd parity No parity
7		í 0 1			8 data bits 7 data bits