ARCHTEK CORPORATION
5634PCA-K
|
Card Type |
Modem/Fax card |
|
Chip Set |
Cirrus Logic |
|
Maximum Modem Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis, V.34, K56flex |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29, T.4, T.30 |
|
Error Correction/Compression |
MNP5, V.42, V.42bis |
|
Fax Class |
Class I |
|
Data Bus |
PCMCIA |
55075
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, ‘+++’, A/ |
|
A, E, H, L, M, P, Q, T, V, W, X, Y |
|
&B, &C, &D, &G, &V, &Z |
|
Extended AT Commands |
|
\J, \T |
|
%A, %G |
|
Special Commands |
|
+MS, -C |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S24, S30 |
|
Note: See MHI Help File for full command documentation. |
PROPRIETARY AT COMMAND SET
|
AUTO-MODE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
|
Command |
Function |
|
N0 |
In originate or answer mode, handshake occurs only in mode designated by the ATB command and S37 register. |
|
í N1 |
In originate or answer mode, handshake begins at line speed designated by the S37 register and ATB command. Modem may shift to a lower speed |
|
AUXILIARY RELAY CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Jn [cmds] |
|
Description: |
Enables/disables A/A1 relay driver. Not for use with RJ-11 phone lines |
|
Command |
Jack Type |
|
&J0 |
Auxiliary relay is never closed |
|
COMMUNICATION PROTOCOLS | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Bn [cmds] |
|
Description: |
Selects the communication protocol for data calls |
Note: The B command allows the simultaneous selection of more than one suffix, enabling multiple protocols. | |
|
Command |
Protocol |
|
B0 |
ITU-T V.22 at 1200bps or V.21 at 300bps |
|
B1 |
Bell 212A at 1200bps/ Bell 103J at 300bps |
|
B2 |
ITU-T V.23 at 75/1200bps originate; 1200/75bps answer |
|
B3 |
ITU-T V.23 at 1200/75bps answer; 75/1200bps originate |
|
B15 |
ITU-T V.22 at 1200bps or V.21 at 300bps |
|
B16 |
Bell 212A at 1200bps/ Bell 103J at 300bps |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Mn [cmds] |
|
Description: |
Selects communications mode |
|
Command |
Mode |
|
&M0 |
Asynchronous mode |
|
COMMUNICATIONS MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Qn [cmds] |
|
Description: |
Selects communications mode |
|
Command |
Mode |
|
&Q0 |
Buffered asynchronous mode |
|
&Q5 |
Error correction mode |
|
&Q6 |
Buffered asynchronous mode |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
&S1 |
DSR high only while modem is handshaking or connected |
|
DATA TERMINAL READY (DTR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Dn [cmds] |
|
Description: |
Selects modem response to DTR |
|
Command |
Function |
|
&D0 |
DTR override |
|
&D1 |
DTR toggle causes online command mode |
|
&D2 |
Normal DTR operations |
|
&D3 |
Resets on receipt of DTR |
|
DIAL | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] D<#> [cmds] |
|
Description: |
Dials telephone number according to any modifiers included in the string |
|
Note: |
Any combination of modifiers can be used to produce the desired dial functions in sequence. |
|
Command |
Function |
|
DL |
Re-dial last number |
|
DP |
Pulse dialing enabled |
|
DS=n |
Dial stored telephone number n |
|
DT |
Tone dialing enabled/Pulse dialing disabled |
|
DW |
Dialing resumed following dial tone detection |
|
D, |
Dialing paused for amount of time specified in S8 register |
|
D! |
Flash function initiated. Modem commanded to go off-hook for specified time before returning on-hook. |
|
D@ |
Wait for Quite Answer function enabled. Modem waits until a "quiet answer," a ring-back signal followed by silence up to the time specified in S7, is received prior to executing the rest of the dial string. |
|
D; |
Modem returned to idle state after dialing. The semicolon can only be placed at the end of the dial command. |
|
D^ |
Data calling tone disabled |
|
D$ |
Wait for credit card "bong" tone before processing the remaining characters in the dial string |
|
ECHOPLEX VALIDITY | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Fn [cmds] |
|
Description: |
Selects whether commands sent while in data mode are echoed |
|
Command |
Function |
|
F1 |
Echoplex disabled |
|
FACTORY DEFAULT PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &F [cmds] |
|
Description: |
Sets values in active profile to values found in the default profile |
|
Command |
Function |
|
&F0 |
Sets values in active profile to factory settings |
|
&F5 |
Sets values in active profile to factory settings for ETC mode |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables flow control options |
|
Command |
Function |
|
&K0 |
Flow control disabled |
|
&K3 |
RTS/CTS hardware flow control enabled |
|
&K4 |
XON/XOFF software flow control enabled |
|
ON-LINE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] On [cmds] |
|
Description: |
Controls on-line command (data transmission) state options. |
Note: The O command must be placed at the end of the command string. | |
|
Command |
Function |
|
O0 |
On-line command mode disabled; return to data mode |
|
O1 |
On-line command mode with retraining enabled |
|
O2 |
Rate negotiation issued before returning to online command mode |
|
PULSE DIALING RATIO | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Pn [cmds] |
|
Description: |
Selects pulse dial make/break ratio |
|
Command |
Function |
|
í &P0 |
39/61ms at 10pps (North America) |
|
&P1 |
33/67ms at 10pps (Europe) |
|
&P2 |
33/67ms at 20pps |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports modem firmware revision information |
|
I1 |
Reports ROM checksum |
|
I2 |
Tests and reports ROM checksum |
|
I3 |
Reports modem firmware revision information |
|
I12 |
Reports country code |
|
RESTORE PROFILE ON POWER-UP | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Yn [cmds] |
|
Description: |
Restores a selected profile into the active profile on power-up (hard reset) |
|
Command |
Function |
|
&Y0 |
Restore profile 0 on power-up |
|
SOFT RESET | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] Zn [cmds] |
|
Description: |
Restores modem profiles previously saved in non-volatile RAM using the &W command. |
|
Command |
Function |
|
Z0 |
Restore setting 0 |
|
STORE ACTIVE PROFILE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Wn [cmds] |
|
Description: |
Writes the values for the active profile into the non-volatile RAM |
|
Command |
Function |
|
&W0 |
Write the active profile to stored profile 0 |
|
TEST MODES | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] &Tn |
|
Description: |
Selects test options |
|
Command |
Function |
|
í &T0 |
End current test |
|
&T1 |
Begin local analog loopback test |
|
&T3 |
Begin local digital loopback request |
|
&T6 |
Request remote digital loopback |
|
TRANSMIT CARRIER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Cn [cmds] |
|
Description: |
Controls the transmit carrier switching |
|
Command |
Function |
|
C1 |
Transmit carrier enabled |
EXTENDED AT COMMANDS
|
BLACKLIST | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] %Bn [cmds] |
|
Description: |
Displays numbers which failed the last call attempt within two hours. In countries that do not require blacklisting, command returns ERROR |
|
BREAK TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Kn [cmds] |
|
Description: |
Configures action of break signal |
|
Command |
Function |
|
í \K5 |
Modem sends break to remote modem in sequence with transmitted data; non-destructive/non-expedited |
|
CONNECT MODE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Nn [cmds] |
|
Description: |
Controls the type of connection the modem will operate in |
|
Command |
Function |
|
\N0 |
Normal mode enabled |
|
\N1 |
Normal mode enabled |
|
\N2 |
Reliable mode enabled |
|
í \N3 |
Auto-reliable mode enabled |
|
\N4 |
V.42 reliable mode enabled |
|
\N5 |
MNP reliable mode enabled |
|
FLOW CONTROL TYPE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Qn [cmds] |
|
Description: |
Sets type of flow control used by modem |
|
Command |
Function |
|
\Q0 |
Flow control disabled |
|
\Q1 |
Bi-directional XON/XOFF flow control enabled |
|
í \Q2 |
RTS/CTS flow control to DTE enabled |
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Gn [cmds] |
|
Description: |
Selects modem port flow control. For compatibility only. |
|
Command |
Function |
|
\G0 |
Returns OK |
|
XON/XOFF PASS-THROUGH | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] \Xn [cmds] |
|
Description: |
Selects whether XON/XOFF signals are sent to remote modem |
|
Command |
Function |
|
\X0 |
XON/XOFF signals trapped by local modem |
SPECIAL COMMANDS
|
IDENTIFY MODEM MANUFACTURER | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] +GMI? [cmds] | |
|
Description: |
Commands DCE to send a message to the DTE indicating the DCE manufacturer | |
|
Note: |
Modem manufacturers name may be changed using the firmware configuration utility | |
|
IDENTIFY PRODUCT MODEL | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] +GMM? [cmds] | |
|
Description: |
Commands DCE to send a message to the DTE indicating the modem chipset name | |
|
Note: |
Modem product model may be changed using the firmware configuration utility | |
|
IDENTIFY PRODUCT REVISION | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] +GMR? [cmds] | |
|
Description: |
Commands DCE to send a message to the DTE indicating the modem chipset revision level | |
|
Note: |
Modem chipset revision level may be changed using the firmware configuration utility | |
S(status) -REGISTERS
|
AUTO MODE | |||
|
Format: |
AT [cmds] S43=n [cmds] | ||
|
Range: |
0-1 | ||
|
Unit: |
Unidentified | ||
|
Description: |
Enables/disables V.32bis start-up mode. | ||
|
Note: |
For testing and debugging purposes only | ||
|
Command |
Function | ||
|
S43=0 |
V.32bis srtart-up mode disabled | ||
|
S43=1 |
V.32bis srtart-up mode enabled | ||
|
AUTO RATE | |||
|
Format: |
AT [cmds] S42=n [cmds] | ||
|
Range: |
0-1 | ||
|
Unit: |
Unidentified | ||
|
Description: |
Enables/disables V.32 and V.22bis auto rate. | ||
|
Note: |
For testing and debugging purposes only | ||
|
Command |
Function | ||
|
S42=0 |
V.32 and V.22bis auto rate disabled | ||
|
S42=1 |
V.32 and V.22bis auto rate enabled | ||
|
BIT-MAPPED REGISTER S14 | ||
|
Format: |
AT [cmds] S14=n [cmds] | |
|
Range: |
0-174 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls result codes display, and dial mode | |
|
Bit |
Value |
Function |
|
2 - 0 |
0 |
Reserved |
|
3 |
0 1 |
Display result codes in numeric format Display result codes in verbose format |
|
6 |
0 1 |
Pulse dial set to 10pps Pulse dial set to 20pps |
|
7 |
0 |
Reserved |
|
BIT-MAPPED REGISTER S21 | ||
|
Format |
AT [cmds] S21=n [cmds] | |
|
Range: |
0-253 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Selects jack type, CTS/DCD/DSR signals, low DTR action, and the long space disconnect function. | |
|
Bit |
Value |
Function |
|
2 - 0 |
0 |
Reserved |
|
4, 3 |
00 01 10 11 |
DTR signal ignored Modem goes to command mode on low DTR Modem disconnects on low DTR; Auto-Answer is disabled. Modem is initialized on low DTR |
|
5 |
0 í 1 |
DCD forced high DCD normal |
|
6, 7 |
0 |
Reserved |
|
BIT-MAPPED REGISTER S22 | ||
|
Format |
AT [cmds] S22=n [cmds] | |
|
Range: |
0-255 | |
|
Unit: |
Bit-mapped | |
|
Description: |
Controls speaker volume and controls, limits results codes, and pulse dial make/break ratio. | |
|
Bit |
Value |
Function |
|
3 - 0 |
0 |
Reserved |
|
6 - 4 |
000 100 101 110 111 |
Basic result codes only enabled Basic and connection speed result codes enabled Basic and connection speed result codes and dialtone detection enabled All result codes except dialtone detection enabled All result codes enabled |
|
7 |
0 1 |
39/61ms at 10pps (North America) 33/67ms at 10pps (Europe) |
|
DATA CALLING TONE | ||
|
Format: |
AT [cmds] S35=n [cmds] | |
|
Range: |
0-1 | |
|
Unit: |
Unidentified | |
|
Description: |
Enables/disables data calling tone. S35=0 disables | |
|
DCE LINE SPEED | |
|
Type: |
Register |
|
Format |
AT [cmds] S37=n [cmds] |
|
Description: |
Sets the maximum allowable data exchange rate attempted during handshake process. |
|
Command |
Function |
|
S37=0 |
Maximum line speed |
|
S37=2 |
1200/75bps |
|
S37=3 |
300bps |
|
S37=5 |
1200bps |
|
S37=6 |
2400bps |
|
S37=7 |
4800bps |
|
S37=8 |
7200bps |
|
S37=9 |
9600bps |
|
S37=10 |
12.0Kbps |
|
S37=11 |
14.4Kbps |
|
S37=12 |
16.8Kbps |
|
S37=13 |
19.2Kbps |
|
S37=14 |
21.6Kbps |
|
S37=15 |
24.0Kbps |
|
S37=16 |
26.4Kbps |
|
S37=17 |
28.8Kbps |
|
S37=18 |
31.2Kbps |
|
S37=19 |
33.6Kbps |
|
56K DCE LINE SPEED | |
|
Type: |
Register |
|
Format |
AT [cmds] S38=n [cmds] |
|
Description: |
Sets the maximum allowable 56K downstream rate attempted during handshake process. |
|
Command |
Function |
|
S38=0 |
56K disabled |
|
S38=1 |
56K automatic speed select |
|
S38=2 |
32.0Kbps |
|
S38=3 |
34.0Kbps |
|
S38=4 |
36.0Kbps |
|
S38=5 |
38.0Kbps |
|
S38=6 |
40.0Kbps |
|
S38=7 |
42.0Kbps |
|
S38=8 |
44.0Kbps |
|
S38=9 |
46.0Kbps |
|
S38=10 |
48.0Kbps |
|
S38=11 |
50.0Kbps |
|
S38=12 |
52.0Kbps |
|
S38=13 |
54.0Kbps |
|
S38=14 |
56.0Kbps |
|
S38=15 |
58.0Kbps |
|
S38=16 |
60.0Kbps |
|
ERROR CORRECTION NEGOTIATION | |
|
Type: |
Register |
|
Format |
AT [cmds] S36=n [cmds] |
|
Description: |
Selects the action of the modem if it fails to connect with the error-correction protocol set in &Q. |
|
Command |
Function |
|
S36=0 |
Hang up |
|
S36=1 |
Fall-back to asynchronous connection |
|
S36=2 |
Hang up |
|
S36=3 |
Fall-back to asynchronous connection |
|
S36=4 |
Attempt a connection at MNP2-4; if that fails, hang up. |
|
S36=5 |
Attempt a connection at MNP2-4; if that fails, fall-back to asynchronous connection |
|
S36=6 |
Attempt a connection at MNP2-4; if that fails, hang up. |
|
í S36=7 |
Attempt a connection at MNP2-4; if that fails, fall-back to asynchronous connection |
|
ETC STARTUP AUTORATING | |
|
Type: |
Register |
|
Format |
AT [cmds] S40=n [cmds] |
|
Description: |
Determines default auto-rating |
|
Command |
Function |
|
S40=0 |
Start up with normal auto-rating |
|
S40=1 |
Start up at initial rate of 4800bps or below |
|
S40=2 |
Start up at initial rate of 9600bps or below |
|
FEATURE NEGOTIATION OPTIONS | |||
|
Type: |
Register | ||
|
Format: |
AT [cmds] S48=n [cmds] | ||
|
Description: |
Selects active error correction and compression protocols | ||
|
Command |
Function | ||
|
S48=7 |
Detection negotiation and XID negotiation enabled | ||
|
S48=128 |
Fall-back to options set in S36 | ||
|
LOCAL PHONE STATUS | |||
|
Type: |
Register | ||
|
Format: |
AT [cmds] S90=n [cmds] | ||
|
Description: |
Displays the status of the local phone | ||
|
Command |
Function | ||
|
S90=0 |
Local phone on-hook | ||
|
S90=1 |
Local phone off-hook | ||
|
SLEEP TIMER | |
|
Type: |
Register |
|
Format |
AT [cmds] S89=n [cmds] |
|
Range: |
0, 5-255 |
|
Unit: |
Unidentified |
|
Description: |
Maximum duration of DTE and DCE inactivity allowed prior to initiating low-power sleep mode. |
|
SYNTHETIC RING FREQUENCY | ||
|
Format: |
AT [cmds] S33=n [cmds] | |
|
Range: |
1-5 | |
|
Unit: |
Unidentified | |
|
Description: |
Determines synthetic ring frequency. S33=0 disables | |
|
SYNTHETIC RING VOLUME | ||
|
Format: |
AT [cmds] S32=n [cmds] | |
|
Range: |
Unidentified | |
|
Unit: |
-1dB | |
|
Description: |
Determines synthetic ring volume | |
|
TRANSMISSION LEVEL - DIRECT CONNECT | |
|
Type: |
Register |
|
Format: |
AT [cmds] S92=n [cmds] |
|
Default: |
20 |
|
Range: |
Unidentified |
|
Unit: |
-1 dBm |
|
Description: |
Sets the signal level for transmission for direct connections |
|
TRANSMISSION LEVEL - LINE | |
|
Type |
Register or Configuration |
|
Format |
AT [cmds] S91=n [cmds] |
|
Range |
6-15 |
|
Unit |
-1 dBm |
|
Description |
Sets the signal level for transmission over phone lines |
|
Note: |
Register only functions for Japan |
|
V.34 MODULATION | |
|
Type: |
Register |
|
Format |
AT [cmds] S28=n [cmds] |
|
Range: |
0-255 |
|
Unit: |
Unidentified |
|
Description: |
Enables V.34 modulation protocol. S28=0 disables |