ACER, INC.
MAGIC MP56
|
Card Type |
Modem (asynchronous), Fax, Sound card |
|
Chip Set |
Unidentified |
|
I/O Options |
CD-ROM interface, game port, wavetable interface, audio line in, audio line out, microphone |
|
Maximum Modem Rate |
56Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.22, V.22bis, V.23, V.32, V.32bis, V.34 |
|
Fax Modulation Protocol |
ITU-T V.17, V.33, V.29, V.27ter, V.21CH2 |
|
Error Correction/Compression |
MNP 5, V.42bis |
|
Fax Class |
Unidentified |
|
Data Bus |
16-bit ISA |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line out |
CN1 |
Wavetable interface |
CN6 | |||
|
Line in |
CN2 |
CD-ROM connector |
CN7 | |||
|
Microphone |
CN3 |
MIDI/Game port |
CN8 | |||
|
Audio line in |
CN4 |
Ring-on connector |
CN9 | |||
|
Speaker/audio line-out |
CN5 | |||||
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
Flash download disabled |
JP4 |
Pins 1 & 2 closed |
|
Flash download enabled |
JP4 |
Pins 2 & 3 closed |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, A/ |
|
A, B, D, E, H, M, O, P, Q, T, V, W, X, Y, Z |
|
&C, &F, &M, &P, &Q, &R, &T, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\K, \N |
|
%E, %L, %Q |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25, |
|
S26, S27, S28, S29, S30, S31, S32, S33, S36, S37, S38, S39, S40, S41, S46, S48, S82, S86, S95 |
|
Special Commands |
|
+MS |
|
Note: See MHI Help File for full command documentation. |
Proprietary AT Command Set
|
AUTO-MODE DETECTION | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Nn [cmds] |
|
Description: |
Selects various options for the automatic detection and negotiation of protocols during the handshake process if the modem is communicating with a remote modem of dissimilar speed. |
|
Command |
Function |
|
N0 |
Auto-mode detection disabled |
|
N1 |
Auto-mode detection enabled |
|
CLOCK SOURCE - SYNCHRONOUS TRANSMIT | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Xn [cmds] |
|
Description: |
Selects DTE transmit clock source |
|
Command |
Function |
|
&X0 |
Modem generates clock |
|
&X1 |
DTE generates clock |
|
DATA SET READY (DSR) | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Sn [cmds] |
|
Description: |
Selects DSR options |
|
Command |
Function |
|
&S0 |
DSR forced high |
|
&S1 |
DSR acts per V.25 |
|
DATA TERMINAL READY (DTR) | |||||
|
Type: |
Configuration | ||||
|
Format: |
AT [cmds] &Dn [cmds] | ||||
|
Description: |
Selects modem response to DTR | ||||
Note: The action each variant of &D causes depends on the setting of &Q | |||||
|
&Q Setting |
&D0 |
&D1 |
&D2 |
&D3 | |
|
&Q0, &Q5, &Q6 |
Command 0 |
Command 1 |
Command 2 |
Command 3 | |
|
&Q1, &Q4 |
Command 2 |
Command 1 |
Command 2 |
Command 3 | |
|
&Q2, &Q3 |
Command 2 |
Command 2 |
Command 2 |
Command 2 | |
|
Command |
Function | ||||
|
Command 0 |
Modem does not respond to DTR | ||||
|
Command 1 |
Modem goes to command mode after DTR goes is off | ||||
|
Command 2 |
Modem goes to command mode and disconnects (hangs up) after DTR goes off; Auto-Answer is disabled. | ||||
|
Command 3 |
Modem is initialized after DTR goes off | ||||
|
FLOW CONTROL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Kn [cmds] |
|
Description: |
Enables flow control options |
|
Command |
Function |
|
&K0 |
Disable DTE/DCE flow control |
|
&K3 |
RTS/CTS flow control enabled |
|
&K4 |
XON/XOFF flow control enabled |
|
&K5 |
Transparent XON/XOFF flow control enabled |
|
&K6 |
Unidirectional XON/XOFF flow control enabled |
|
GUARD TONE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] &Gn [cmds] |
|
Description: |
Commands the modem to transmit a guard tone in V.22/V.22bis |
Note: Used primarily for international data transmission | |
|
Command |
Function |
|
&G0 |
Guard tone disabled |
|
&G1 |
Guard tone disabled |
|
&G2 |
1800Hz guard tone enabled |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays information requested |
|
Command |
Function |
|
I0 |
Reports modem model and speed |
|
I1 |
Reports ROM checksum |
|
I2 |
Tests and reports ROM checksum |
|
I3 |
Report firmware revision, model and interface type |
|
I4 |
Report response programmed by OEM |
|
I5 |
Report the country code parameter |
|
I6 |
Report modem data pump model and code revision |
|
SPEAKER VOLUME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Ln [cmds] |
|
Description: |
Controls speaker volume |
|
Command |
Function |
|
L0 |
Low volume setting |
|
L1 |
Low volume setting |
|
L2 |
Medium volume setting |
|
L3 |
Highest volume setting |
|
TRANSMIT CARRIER | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Cn [cmds] |
|
Description: |
Controls the transmit carrier switching |
S(status) -REGISTERS
|
AUTO SYNCHRONIZATION OPTION | |
|
Format |
AT [cmds] S19=n [cmds] |
|
Default: |
0 |
|
Range: |
Unidentified |
|
Unit: |
Unidentified |
|
Description: |
Options are unidentified |
|
BIT-MAPPED REGISTER S20 | |
|
Format |
AT [cmds] S20=n [cmds] |
|
Default: |
0, |
|
Range: |
0-253 |
|
Unit: |
Bit-mapped |
|
Description: |
Selects auto-sync HDLC address or BSC sync character |
