APACHE MICRO PERIPHERALS, INC.
APACHE V34IV-SP+
|
Card Type |
Modem (synchronous/asynchronous) |
|
Chip Set |
Unidentified |
|
I/O Options |
Voice, speakerphone |
|
Maximum Data Rate |
33.6Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
Unidentified |
|
Fax Class |
Class I & II |
|
Data Modulation Protocol |
Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC |
|
Fax Modulation Protocol |
Unidentified |
|
Error Correction/Compression |
MNP5, V.42, V.42bis, RPI |
52997
|
USER CONFIGURABLE SETTINGS | ||
|
Setting |
Label |
Position |
|
í Factory configured - do not alter |
SW1/7 |
Unidentified |
|
í Factory configured - do not alter |
SW1/8 |
N/A |
Note: SW1/8 may not be present on all models. | ||
|
INTERRUPT SELECTION | ||||
|
Setting |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
|
í IRQ3 |
Off |
Off |
Off |
On |
|
IRQ4 |
Off |
Off |
On |
Off |
|
IRQ5 |
Off |
On |
Off |
Off |
|
IRQ7 |
On |
Off |
Off |
Off |
|
SERIAL PORT ADDRESS SELECTION | ||
|
Setting |
SW1/5 |
SW1/6 |
|
3F8h (COM1:) |
On |
On |
|
2F8h (COM2:) |
Off |
On |
|
3E8h (COM3:) |
On |
Off |
|
í 2E8h (COM4:) |
Off |
Off |
|
MISCELLANEOUS TECHNICAL NOTE |
|
Diagram not available. |
|
SUPPORTED STANDARD COMMANDS |
|
Basic AT Commands |
|
+++, comma, A/ |
|
A, B, D, E, H, L, M, N, O, P, Q, T, V, W, X, Y |
|
&C, &D, &F, &G, &K, &M, &P, &Q, &R, &S, &T, &V, &W, &X, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \K, \N, \V |
|
%C, %E, %F, %L, %Q, %TT |
|
Special AT Commands |
|
#CID, +MS |
|
S-Registers |
|
The S-registers are unidentified. |
Note: See MHI documentation for complete information. |
Proprietary AT Command Set
|
DISPLAY MANUFACTURER | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #MFR? [cmds] |
|
Description: |
Displays the manufacturers name. |
|
DISPLAY MODEL NAME | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #MDL? [cmds] |
|
Description: |
Displays the model name of the modem. |
|
DISPLAY REVISION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #REV? [cmds] |
|
Description: |
Displays the revision level of the modem. |
|
DISTINCTIVE RING | |||||
|
Format: |
AT [cmds] -SDR=n [cmds] | ||||
|
Default: |
Unidentified | ||||
|
Range: |
0 - 7 | ||||
|
Description: |
Selects which distinctive ring signals the modem will respond to. | ||||
|
Bit |
Value |
Function | |||
|
0 |
0 1 |
Do not respond to distinctive ring type 1. Respond to distinctive ring type 1. | |||
|
1 |
0 1 |
Do not respond to distinctive ring type 2. Respond to distinctive ring type 2. | |||
|
2 |
0 1 |
Do not respond to distinctive ring type 3. Respond to distinctive ring type 3. | |||
|
DSVD MODE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] -SSE=n [cmds] | |
|
Description: |
Select whether the modem will use DSVD mode. | |
|
Command |
Function | |
|
í -SSE=0 |
DSVD mode disabled. | |
|
-SSE=1 |
DSVD mode enabled. | |
|
FIRMWARE DOWNLOAD | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] **n [cmds] | |
|
Description: |
Downloads new code to the firmware flash memory. | |
|
Command |
Function | |
|
**0 |
Download at speed of last command. | |
|
**1 |
Download at 38.4Kbps. | |
|
**2 |
Download at 57.6Kbps. | |
|
MODE SELECTION | ||
|
Type: |
Immediate | |
|
Format: |
AT [cmds] #CLS=n [cmds] | |
|
Description: |
Selects which mode the modem will operate in. | |
|
Command |
Function | |
|
#CLS=0 |
Modem will operate in data mode. | |
|
#CLS=1 |
Modem will operate in fax class I mode. | |
|
#CLS=2 |
Modem will operate in fax class II mode. | |
|
#CLS=8 |
Modem will operate in voice mode. | |
|
PROTOCOL/SPEED | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] Fn [cmds] |
|
Description: |
Selects the protocol and speed the modem will attempt to connect at. |
|
Command |
Function |
|
F0 |
Auto-detect the highest common connect speed. |
|
F1 |
Select V.21 or Bell 103 at 300bps speed. |
|
F3 |
Select V.23 at 75/1200bps speed. |
|
F4 |
Select V.22 or Bell 212A at 1200bps speed. |
|
F5 |
Select V.22bis at 2400bps speed. |
|
F6 |
Select V.32 or V.32bis at 4800bps speed. |
|
F7 |
Select V.32bis at 7200bps speed. |
|
F8 |
Select V.32bis or V.32 at 9600bps speed. |
|
F9 |
Select V.32bis at 12Kbps speed. |
|
F10 |
Select V.32bis at 14.4Kbps speed. |
|
REPORT INFORMATION | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] In [cmds] |
|
Description: |
Displays requested information about the modem. |
|
Command |
Function |
|
I0 |
Reports product identification code. |
|
I1 |
Reports ROM checksum. |
|
I2 |
Tests and reports ROM checksum. |
|
I3 |
Reports modem firmware version and interface type. |
|
I4 |
Reports OEM response. |
|
I5 |
Reports country code. |
|
I6 |
Reports data pump model and revision. |
|
I7 |
Reports DAA code. |
|
RPI CONFIGURATION | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] +Hn [cmds] | |
|
Description: |
Configures the Rockwell Protocol Interface. | |
|
Command |
Function | |
|
+H0 |
RPI disabled. | |
|
+H1 |
RPI enabled and local serial port speed set to 19.2Kbps. | |
|
+H2 |
RPI enabled and local serial port speed set to 38.4Kbps. | |
|
+H3 |
RPI enabled and local serial port speed set to 57.6Kbps. | |
|
+H11 |
RPI+ enabled. | |
|
SPEAKERPHONE OPTIONS | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] #SPK=x,y,z [cmds] | |
|
Description: |
Sets various options for speakerphone functions. | |
|
Command |
Function | |
|
x =0 |
Microphone enabled. | |
|
x =1 |
Microphone disabled. | |
|
x =2 |
Microphone enabled with maximum gain, speaker disabled. | |
|
Default (y): |
5 | |
|
Range (y): |
0 - 16 | |
|
Unit (y): |
-2 dBm | |
|
Description (y): |
Sets the attenuation level for speaker output in voice mode. | |
|
z =0 |
Microphone gain set to 0 dBm. | |
|
z =1 |
Microphone gain set to 6 dBm. | |
|
z =2 |
Microphone gain set to 9.5 dBm. | |
|
z =3 |
Microphone gain set to 12 dBm. | |
|
TONE DETECTION | |||||
|
Format: |
AT [cmds] #VTD=x,y,z [cmds] | ||||
|
Default: |
x ,y,z 63 | ||||
|
Range: |
0 - 63 | ||||
|
Description: |
Sets which tones the tone detection will report. | ||||
|
Note: |
The value of x sets the tone detection modes in voice transmit mode, y sets them in voice receive mode, and z sets them in voice command mode. | ||||
|
Bit |
Value |
Function | |||
|
0 |
0 í 1 |
DTMF tones are not detected. DTMF tones are detected. | |||
|
1 |
0 í 1 |
V.25 1300Hz calling tone is not detected. V.25 1300Hz calling tone is detected. | |||
|
2 |
0 í 1 |
T.30 1100Hz fax tone is not detected. T.30 1100Hz fax tone is detected. | |||
|
3 |
0 í 1 |
V.25/T.30 2100Hz answer tone is not detected. V.25/T.30 2100Hz answer tone is detected. | |||
|
4 |
0 í 1 |
Bell 2225Hz answer tone is not detected. Bell 2225Hz answer tone is detected. | |||
|
5 |
0 í 1 |
Call progress tones are not detected. Call progress tones are detected. | |||
|
TONE GENERATOR - DIRECT ENTRY | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #VTS=[m, n, x] |
|
Range: |
m 200-3000, n 200-3000, x 0-255 |
|
Unit: |
m 1 Hz, n 1 Hz, x .1 second |
|
Description: |
Generates a dual-frequency tone for duration x at frequencies m and n. |
|
TONE GENERATOR - TIMED PHONE KEYS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #VTS={a, n} |
|
Range: |
a 0-9, A-D, #, *; x 0-255 |
|
Unit: |
x .1 second |
|
Description: |
Generates the DTMF tone for duration x for the character a. |
|
TONE GENERATOR - PHONE KEYS | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #VTS=a |
|
Range: |
0-9, A-D, #, * |
|
Description: |
Generates the DTMF tones for the characters in the string for the duration set with +VBT. |
|
TONE GENERATOR LENGTH | |
|
Format |
AT [cmds] #VBT=n [cmds] |
|
Default: |
10 |
|
Range: |
0 - 40 |
|
Unit: |
0.1 second |
|
Description: |
Sets the length of DTMF tones that are generated. |
|
VOICE BUFFER SPACE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VSK=n [cmds] |
|
Default: |
255 |
|
Range: |
0 - 255 |
|
Unit: |
1 byte |
|
Description: |
Sets the amount of data the modem can send into the buffer after the XOFF signal is sent. |
|
VOICE DEVICE | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VLS=n [cmds] |
|
Description: |
Selects the I/O device for the DSP chip. |
|
Command |
Function |
|
í #VLS=0 |
Telephone line and handset used for voice I/O. |
|
#VLS=1 |
Telephone handset used for voice I/O. |
|
#VLS=2 |
Internal speaker only used for voice I/O. |
|
#VLS=3 |
External microphone only used for voice I/O. |
|
#VLS=4 |
Telephone line and handset used for voice I/O; internal speaker enabled. |
|
#VLS=5 |
Headset used for voice I/O. |
|
#VLS=6 |
Speakerphone used for voice I/O. |
|
VOICE - DISPLAY BUFFER SIZE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #VBQ? [cmds] |
|
Description: |
Displays the size of the voice buffer. |
|
VOICE - DISPLAY COMPRESSION TYPE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #VCI? [cmds] |
|
Description: |
Displays the type of compression currently in use. |
|
VOICE - LOCAL SERIAL PORT SPEED | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] #BDR=n [cmds] | |
|
Description: |
Sets the speed of the local serial port when in voice mode. | |
|
Command |
Function | |
|
#BDR=1 |
Set speed to 2400bps. | |
|
#BDR=2 |
Set speed to 4800bps. | |
|
#BDR=4 |
Set speed to 9600bps. | |
|
#BDR=6 |
Set speed to 14.4Kbps. | |
|
#BDR=8 |
Set speed to 19.2Kbps. | |
|
#BDR=16 |
Set speed to 38.4Kbps. | |
|
#BDR=24 |
Set speed to 57.6Kbps. | |
|
VOICE RE-RING DETECT TIME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VRA=n [cmds] |
|
Default: |
70 |
|
Range: |
0-255 |
|
Unit: |
10 mS |
|
Description: |
Sets the maximum time the modem will wait for the remote station to ring again before it assumes that it has gone off-hook. |
|
VOICE RECEIVE | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #VRX |
|
Description: |
Commands the modem to begin receiving voice data. |
|
VOICE RING DETECT TIME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VRN=n [cmds] |
|
Default: |
Unidentified |
|
Range: |
Unidentified |
|
Unit: |
Unidentified |
|
Description: |
Sets the maximum time the modem will wait for the remote station to ring before it assumes that it went off-hook before it rang. |
|
VOICE SAMPLE QUALITY | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] #VBS=n [cmds] | |
|
Description: |
Selects the number of bits per sample that the modem records. | |
|
Command |
Function | |
|
#VBS=2 |
Modem records 2 bits per sample in ADPCM encoding. | |
|
#VBS=3 |
Modem records 3 bits per sample in ADPCM encoding. | |
|
í #VBS=4 |
Modem records 4 bits per sample in ADPCM encoding. | |
|
VOICE SAMPLING RATE | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] #VSR=n [cmds] | |
|
Description: |
Sets the sampling rate used when recording voice signals. | |
|
Command |
Function | |
|
#VSR=7200 |
Selects a sampling rate of 7.2KHz. | |
|
#VSR=11025 |
Selects a sampling rate of 11.025KHz in PCM encoding only. | |
|
VOICE SILENCE DETECTION TIME | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VSP=n [cmds] |
|
Default: |
Unidentified |
|
Range: |
0 - 255 |
|
Unit: |
.1 second |
|
Description: |
Sets the minimum amount of silence that the modem will detect. |
|
VOICE SILENCE DETECTION THRESHOLD | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] #VSS=n [cmds] | |
|
Description: |
Sets the threshold of sensitivity that the modem uses to determine silence detection. | |
|
Command |
Function | |
|
#VSS=0 |
Silence detection disabled. | |
|
#VSS=1 |
Minimum silence detection sensitivity. | |
|
#VSS=2 |
Standard silence detection sensitivity. | |
|
#VSS=3 |
Maximum silence detection sensitivity. | |
|
VOICE TIMING MARK | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] #VTM=n [cmds] | |
|
Description: |
Configures timing mark placement. | |
|
Command |
Function | |
|
#VTM=0 |
Timing marks disabled. | |
|
#VTM=1 |
Timing marks enabled. | |
|
VOICE TRANSMISSION LEVEL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #TL=hhhh [cmds] |
|
Default: |
3FFF |
|
Range: |
0000 - 7FFF |
|
Unit: |
Unidentified (hexadecimal) |
|
Description: |
Sets the transmission level for sending audio in voice mode. |
|
VOICE TRANSMIT | |
|
Type: |
Immediate |
|
Format: |
AT [cmds] #VTX |
|
Description: |
Commands the modem to begin transmitting voice data. |
|
VOICE VOLUME LEVEL | |
|
Type: |
Configuration |
|
Format: |
AT [cmds] #VGT=n [cmds] |
|
Description: |
Sets the volume level when playing back audio signals. |