ADC KENTROX
DATASMART T3/E3 SMDSU MODEL 1596X (DC POWER)
|
Card Type |
T3/E3 CSU/DSU |
|
Chipset |
Unidentified |
|
T3/E3 Transfer Rate |
34.368Mbps (E3) /44.736Mbps (T3) |
|
T3/E3 Protocol |
M13, C-Bit, G.751, B8ZS |
|
Frame Type |
Unidentified |
|
Data Bus |
Serial |
|
CONNECTIONS | |||
|
Function |
Label |
Function |
Label |
|
Monitor jack |
CN1 |
T3/E3 line in/out |
CN8 |
|
Monitor jack |
CN2 |
T3/E3 line in/out |
CN9 |
|
DCE serial control port |
CN3 |
RS-422 auxiliary clock port |
CN10 |
|
DTE serial control port |
CN4 |
Alarm cutoff switch |
S5 |
|
V.35 serial data port via DB-25 connector |
CN5 |
DC power in (see pinout below) |
SC1 |
|
HSSI serial data port |
CN6 |
Alarm relay (see pinout below) |
SC2 |
|
HSSI serial data port |
CN7 | ||
|
Note:Standard V.35 serial port is provided on an included adapter cable. | |||
|
SC1 PINOUT | |||
|
Function |
Screw |
Function |
Screw |
|
-40V to -56VDC power in |
1 |
+40 to +56VDC power in |
3 |
|
Ground |
2 | ||
|
SC2 PINOUT | |||
|
Function |
Screw |
Function |
Screw |
|
Normally closed contact |
1 |
Normally open contact |
3 |
|
Signal common |
2 | ||
|
USER CONFIGURABLE SETTINGS | |||
|
Setting |
Label |
Position | |
| » |
Control port parity disabled |
S1/3 |
On |
|
Control port parity enabled |
S1/3 |
Off | |
| » |
Control port parity set to odd |
S1/4 |
On |
|
Control port parity set to even |
S1/4 |
Off | |
| » |
Control port uses 8 data bits |
S1/5 |
On |
|
Control port uses 7 data bits |
S1/5 |
Off | |
| » |
Control port uses 1 stop bit |
S1/6 |
On |
|
Control port uses 2 stop bits |
S1/6 |
Off | |
| » |
Alarm reporting disabled |
S1/7 |
On |
|
Alarm reporting enabled |
S1/7 |
Off | |
| » |
Alarm reporting output to DCE control port |
S1/8 |
On |
|
Alarm reporting output to DTE control port |
S1/8 |
Off | |
| » |
Adapter in SMDS mode |
S2/3 |
On |
|
Adapter in DSU mode |
S2/3 |
Off | |
| » |
T3/E3 receive equalization enabled |
S2/4 |
On |
|
T3/E3 receive equalization disabled |
S2/4 |
Off | |
| » |
T3/E3 transmit Line Build Out out |
S2/5 |
On |
|
T3/E3 transmit Line Build Out in |
S2/5 |
Off | |
| » |
Factory configured - do not alter |
S2/6 |
On |
| » |
Factory configured - do not alter |
S2/7 |
On |
| » |
Factory configured - do not alter |
S2/8 |
On |
|
CONTROL PORT SPEED SELECTION | |||
|
Setting |
S1/1 |
S1/2 | |
| » |
9600bps |
On |
On |
|
4800bps |
On |
Off | |
|
2400bps |
Off |
On | |
|
1200bps |
Off |
Off | |
|
PROTOCOL SELECTION | |||
|
Setting |
S2/1 |
S2/2 | |
| » |
T3 MI3 |
On |
On |
|
T3 C-Bit |
On |
Off | |
|
E3 G.751 |
Off |
On | |
|
E3 G.751 |
Off |
Off | |
|
THUMBWEEL FUNCTION SELECTION | |||
|
Function |
S3 |
S4 |
S5 |
|
Reset loopback tests |
Pushed |
Position 0 |
Not pushed |
|
Begin remote line loopback test |
Pushed |
Position 1 |
Not pushed |
|
Begin remote payload loopback test |
Pushed |
Position 2 |
Not pushed |
|
Reset to factory defaults and switch settings |
Pushed for 2 sec. |
Position 3 |
Pushed for 2 sec. |
|
Begin near-end line loopback test |
Pushed |
Position 4 |
Not pushed |
|
Begin near-end payload loopback test |
Pushed |
Position 5 |
Not pushed |
|
Begin near-end local loopback test |
Pushed |
Position 6 |
Not pushed |
|
Begin data near-end terminal loopback test |
Pushed |
Position 7 |
Not pushed |
|
Reset SMDSU address to 00:00:000 |
Pushed for 2 sec. |
Position 7 |
Pushed for 2 sec. |
|
Note:S3 and S5 must always be held for at least one-half of one second for the above functions to take effect. | |||
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
PWR |
Green |
On |
Power is on |
|
PWR |
Red |
On |
Self-test failed |
|
PWR |
N/A |
Off |
Power is off |
|
LOOP |
Yellow |
On |
Local loopback test in progress |
|
LOOP |
Yellow |
Blinking |
Remote loopback test in progress |
|
LOOP |
Yellow |
Off |
Loopback test not in progress |
|
SEND |
Yellow |
On |
Test code being sent |
|
SEND |
Yellow |
Blinking |
Remote loopback test may be in progress but cannot be verified |
|
SEND |
Yellow |
Off |
Test code not being sent |
|
ALM |
Red |
On |
Alarm condition detected and awaiting user intervention |
|
ALM |
Green |
On |
Alarm condition detected; user intervention in progress |
|
ALM |
N/A |
Off |
Alarm condition not detected |
|
RCV |
Green |
On |
DSU is receiving data from network |
|
RCV |
Green |
Off |
DSU is not receiving data from network |
|
XMT |
Green |
On |
DSU is transmitting data to network |
|
XMT |
Green |
Off |
DSU is not transmitting data to network |
|
FEI |
Red |
On |
Remote is out of PLCP lock |
|
FEI |
Red |
Blinking |
Remote PLCP Code Violation detected |
|
FEI |
Red |
Off |
Remote PLCP normal |
|
NEI |
Red |
On |
Local DSU is out of PLCP lock |
|
NEI |
Red |
Blinking |
Local DSU PLCP Code Violation detected |
|
NEI |
Red |
Off |
Local DSU PLCP normal |
|
TXD |
Yellow |
On |
Control port is transmitting data |
|
TXD |
Yellow |
Off |
Control port is not transmitting data |
|
DIAGNOSTIC LED(S) (CON’T) | |||
|
LED |
Color |
Status |
Condition |
|
RXD |
Yellow |
On |
Control port is receiving data |
|
RXD |
Yellow |
Off |
Control port is not receiving data |
|
TA |
Yellow |
On |
V.24 DTR or V.35 TA signal is high |
|
TA |
Yellow |
Off |
V.24 DTR or V.35 TA signal is low |
|
CA |
Yellow |
On |
V.24 DCD or V.35 CA signal is high |
|
CA |
Yellow |
Off |
V.24 DCD or V.35 CA signal is low |
|
DATA |
Green |
On |
Valid data signal detected |
|
DATA |
Green |
Off |
No valid signal detected |
|
CV |
Red |
On |
Code Violation error detected |
|
CV |
Red |
Off |
Code Violation error not detected |
|
LOS |
Red |
On |
Loss Of Signal condition detected |
|
LOS |
Red |
Off |
Loss Of Signal condition not detected |
|
OOF |
Red |
On |
Signal is out of frame synchronization |
|
OOF |
Red |
Off |
Signal is not out of frame synchronization |
|
AIS |
Red |
On |
Alarm Indication Signal condition detected |
|
AIS |
Red |
Off |
Alarm Indication Signal condition not detected |
|
YEL |
Yellow |
On |
Remote Yellow Alarm condition detected |
|
YEL |
Yellow |
Blinking |
Local Yellow Alarm condition detected |
|
YEL |
Yellow |
Off |
Yellow Alarm condition not detected |
