BANKSIA TECHNOLOGY PTY., LTD.
MY MODEM
|
Card Type |
Fax, Modem (asynchronous) |
|
Chip Set |
Unidentified |
|
Maximum Data Rate |
14.4Kbps |
|
Maximum Fax Rate |
14.4Kbps |
|
Data Bus |
External |
|
Fax Class |
Class I & II |
|
Data Modulation Protocol |
Bell 103/212A ITU-T V.21, V.22, V.22bis, V.32, V.32bis |
|
Fax Modulation Protocol |
ITU-T V.17, V.27ter, V.29 |
|
Error Correction/Compression |
MNP5, MNP10, V.42, V.42bis |
|
CONNECTIONS | ||||||
|
Function |
Label |
Function |
Label | |||
|
Line out |
CN1 |
DC power |
CN4 | |||
|
Line in |
CN2 |
Power switch |
SW1 | |||
|
RS-232/422 |
CN3 | |||||
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
PWR |
Red |
On |
Power is on |
|
PWR |
Red |
Off |
Power is off |
|
OH |
Red |
On |
Modem is off-hook |
|
OH |
Red |
Off |
Modem is on-hook |
|
DTR |
Red |
On |
DTR signal is high |
|
DTR |
Red |
Off |
DTR signal is low |
|
DCD |
Red |
On |
Carrier signal detected |
|
DCD |
Red |
Off |
Carrier signal not detected |
|
CTS |
Red |
On |
Modem ready to receive data |
|
CTS |
Red |
Off |
Modem not ready to receive data |
|
RTS |
Red |
On |
Computer ready to receive data |
|
RTS |
Red |
Off |
Computer not ready to receive data |
|
RXD |
Red |
On |
Modem is receiving data |
|
RXD |
Red |
Off |
Modem is not receiving data |
|
TXD |
Red |
On |
Modem is transmitting data |
|
TXD |
Red |
Off |
Modem is not transmitting data |
|
AA |
Red |
On |
Auto-answer enabled |
|
AA |
Red |
Off |
Auto-answer disabled |
|
TST |
Red |
On |
Modem in test mode |
|
TST |
Red |
Off |
Modem not in test mode |
|
SUPPORTED COMMAND SET |
|
Basic AT Commands |
|
AT, ‘+++’, ‘Comma’, A/ |
|
A, B, E, H, I, L, M, N, O, P, Q, S, T, V, W, X, Y, Z |
|
&C, &D, &F, &K, &L, &P, &S, &T, &V, &W, &Y, &Z |
|
Extended AT Commands |
|
\A, \B, \G, \L, %C, %L, %Q |
|
S Registers |
|
S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S24, S25, S26 |
|
S29, S30, S31, S32, S33, S36, S37, S38, S39, S46, S48, S82, S86, S91, S92, S95 |
|
Special Commands |
|
*H, -K, -Q, )M, @M, :E, +MS |
|
Note: See MHI Help file for full command documentation. |
Proprietary AT Command Set
|
MODULATION SELECTION | ||
|
Type: |
Configuration | |
|
Format: |
AT [cmds] Fn [cmds] | |
|
Description: |
Controls line modulation unless automode is selected | |
|
Command |
Function | |
|
F0 |
Automode enabled | |
|
F1 |
Force V.21 or Bell103 (according to ATB command) at 300bps | |
|
F2 |
‘OK’ returned | |
|
F3 |
Force V.23 75TX/1200RX originate or 1200TX/75RX answer FSK | |
|
F4 |
Force V.22 or Bell212A (according to ATB command) at 1200bps | |
|
F5 |
Force V.22bis or Bell2400 (according to ATB command) | |
|
F6 |
Force V.32 at 4800bps | |
|
F7 |
Force V.32 at 7200bps | |
|
F8 |
Force V.32 at 9600bps | |
|
F9 |
Force V.32bis at 12000bps | |
|
F10 |
Force V.32bis at 14400bps | |
For remaining proprietary command summary, See BANKSIA TECHNOLOGY PTY., LTD., MAC MODEM 288.
