THOMAS-CONRAD CORPORATION
TC3045-UTP (REV. A)
|
Card Type |
Network Interface Card |
|
NIC Type |
TCNS |
|
Maximum Onboard Memory |
Unidentified |
|
Boot ROM |
Available |
|
Network Transfer Rate |
100Mbps |
|
Topology |
Star |
|
Wiring Type |
Unshielded twisted pair |
|
Data Bus |
16-bit ISA |
|
CONNECTIONS | |
|
Function |
Label |
|
UTP connector |
CN1 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Label |
Position | |
| » |
16K Block decode size |
SW1/2 |
On |
|
128K Block decode size |
SW1/2 |
Off | |
| » |
Factory configured - do not alter. |
SW3/1 |
Unidentified |
| » |
Enhanced operating mode |
SW3/2 |
Off |
|
Compatible operating mode |
SW3/2 |
On | |
|
WAIT STATE SELECTION | ||
|
Setting |
SW1/1 | |
| » |
0 Wait |
Off |
|
Wait |
On | |
|
BASE I/O ADDRESS SELECTION | |||||||
|
Setting |
SW3/3 |
SW3/4 |
SW3/5 |
SW3/6 |
SW3/7 |
SW3/8 | |
| » |
2E0h |
Off |
On |
On |
On |
Off |
On |
|
2F0h |
On |
On |
On |
On |
Off |
On | |
|
300h |
Off |
Off |
Off |
Off |
On |
On | |
|
350h |
On |
Off |
On |
Off |
On |
On | |
|
BASE MEMORY ADDRESS SELECTION | |||||||
|
Setting |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
SW1/7 |
SW1/8 | |
| » |
D000h |
Off |
Off |
On |
Off |
On |
On |
|
C000h |
Off |
Off |
Off |
Off |
On |
On | |
|
C400h |
On |
Off |
Off |
Off |
On |
On | |
|
C800h |
Off |
On |
Off |
Off |
On |
On | |
|
CC00h |
On |
On |
Off |
Off |
On |
On | |
|
D400h |
On |
Off |
On |
Off |
On |
On | |
|
D800h |
Off |
On |
On |
Off |
On |
On | |
|
DC00h |
On |
On |
On |
Off |
On |
On | |
|
E000h |
Off |
Off |
Off |
On |
On |
On | |
|
INTERRUPT SELECTION |
|
Note: Configuration for IRQ selection (JP1) is unidentified. Note: If you are installing the TC3045 in an 8-bit slot, make sure that the interrupt is set to 2/9, 3, 5, or 7. The TC3045 will not operate if the IRQ is set to any of the other settings. |
|
NODE ADDRESS | ||||||||
|
Node |
SW2/1 |
SW2/2 |
SW2/3 |
SW2/4 |
SW2/5 |
SW2/6 |
SW2/7 |
SW2/8 |
|
1 |
On |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
|
2 |
Off |
On |
Off |
Off |
Off |
Off |
Off |
Off |
|
3 |
On |
On |
Off |
Off |
Off |
Off |
Off |
Off |
|
4 |
Off |
Off |
On |
Off |
Off |
Off |
Off |
Off |
|
251 |
On |
On |
Off |
On |
On |
On |
On |
On |
|
252 |
Off |
Off |
On |
On |
On |
On |
On |
On |
|
253 |
On |
Off |
On |
On |
On |
On |
On |
On |
|
254 |
Off |
On |
On |
On |
On |
On |
On |
On |
|
255 |
On |
On |
On |
On |
On |
On |
On |
On |
|
Note: Node 0 is reserved by the system and should not be used. Note: A total of 255 base address settings are available. The switches are a binary representation of the decimal memory addresses. SW2/8 is the Most Significant Bit and switch SW2/1 is the Least Significant Bit. The switches have the following decimal values: SW2/8=128, SW2/7=64, SW2/6=32, SW2/5=16, SW2/4=8, SW2/3=4, SW2/2=2, SW2/1=1. Turn on the switches and add the values of the switches to obtain the correct memory address. (Off=0, On=1) | ||||||||
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
LED1 |
Red |
On |
Data is being transmitted/received |
|
LED1 |
Red |
Blinking |
Network connection is broken |
|
LED1 |
Red |
Off |
Data is not being transmitted/received |
