PURE DATA LTD.

PDI515

NIC Type

ARCnet

Transfer Rate

2.5Mbps

Data Bus

16-bit ISA

Topology

Star

Linear Bus

Wiring Type

RG-62A/U 93ohm coaxial

Shielded/Unshielded twisted pair

Boot ROM

Available

NODE ADDRESS

Node

SW1/1

SW1/2

SW1/3

SW1/4

SW1/5

SW1/6

SW1/7

SW1/8

0

-

-

-

-

-

-

-

-

1

On

On

On

On

On

On

On

Off

2

On

On

On

On

On

On

Off

On

3

On

On

On

On

On

On

Off

Off

4

On

On

On

On

On

Off

On

On

251

Off

Off

Off

Off

Off

On

Off

Off

252

Off

Off

Off

Off

Off

Off

On

On

253

Off

Off

Off

Off

Off

Off

On

Off

254

Off

Off

Off

Off

Off

Off

Off

On

255

Off

Off

Off

Off

Off

Off

Off

Off

Note:Node address 0 is used for messaging between nodes and must not be used.

A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 8 is the Least Significant Bit and switch 1 is the Most Significant Bit. The switches have the following decimal values: switch 8=1, 7=2, 6=4, 5=8, 4=16, 3=32, 2=64, 1=128. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, off=1)

MEMORY ADDRESS MODE

Mode

SW2/1

»

16-bit memory addressing mode

On

 

8-bit memory addressing mode

Off

Note:Two boot ROMs must be installed for 16-bit memory addressing mode.

COMPATABILITY MODE

Mode

SW2/2

»

Normal

Off

 

Special

On

BASE MEMORY ADDRESS

Address

SW2/3

SW2/4

SW2/5

C0000 - C3FFFh

On

On

On

C4000 - C7FFFh

On

On

Off

CC000 - CFFFFh

On

Off

On

D0000 - D3FFFh

On

Off

Off

D4000 - D7FFFh

Off

On

On

D8000 - DBFFFh

Off

On

Off

DC000 - DFFFFh

Off

Off

On

I/O BASE ADDRESS

Address

SW2/6

SW2/7

SW2/8

260h

On

On

On

290h

On

On

Off

2E0h

On

Off

On

2F0h

On

Off

Off

300h

Off

On

On

350h

Off

On

Off

380h

Off

Off

On

3E0h

Off

Off

Off

CABLE TYPE

Type

JP1A & JP1B

»

Shielded/Unshielded twisted pair

Pins 1 & 2 Closed

 

RG-62A/U 93ohm coaxial

Pins 2 & 3 Closed

MEMORY MODE

Mode

JP2

»

Shared Memory mode enabled

Pins 2 & 3 Closed

 

Mapped I/O mode enabled

Pins 1 & 2 Closed

Note:When Mapped I/O mode is enabled, SW2/1 (Memory address mode) must be in 8-bit mode (off).

TOPOLOGY CONFIGURATION

Topology

JP3

»

Star Topology

Pins 1 & 2 Closed

 

Bus Topology

Pins 2 & 3 Closed

INTERRUPT REQUEST

IRQ

JP4A

JP4B

JP4C

JP4D

JP5A

JP5B

JP5C

JP5D

JP5E

JP5F

2

Open

Open

Open

Open

Closed

Open

Open

Open

Open

Open

3

Open

Open

Open

Open

Open

Closed

Open

Open

Open

Open

4

Open

Open

Open

Open

Open

Open

Closed

Open

Open

Open

5

Open

Open

Open

Open

Open

Open

Open

Closed

Open

Open

6

Open

Open

Open

Open

Open

Open

Open

Open

Closed

Open

7

Open

Open

Open

Open

Open

Open

Open

Open

Open

Closed

10

Closed

Open

Open

Open

Open

Open

Open

Open

Open

Open

11

Open

Closed

Open

Open

Open

Open

Open

Open

Open

Open

12

Open

Open

Closed

Open

Open

Open

Open

Open

Open

Open

15

Open

Open

Open

Closed

Open

Open

Open

Open

Open

Open

DIAGNOSTIC LED(S)

Color

Status

Condition

Red

Flasing on power-up

Card is performing a self-test

Red

On

I/O bus activity detected

Red

Off

No I/O bus activity detected

Green

On

Data is being transmitted or receiving

Green

Blinking

Card is not connected to network or network not active

Hosted by uCoz