Card Type	Modem(asynchronous), Fax, NIC
Chip Set	Intel 82595TX
Maximum Onboard Memory	32KB, 128KB for LAN buffers
Network Rate	10Mbps
Maximum Data Rate	28.8Kbps
Maximum Fax Rate	14.4Kbps
Data Bus	PCMCIA Type II
Fax Class	Class I & II
Data Modulation Protocol	Bell 103A/212A ITU-T V.21, V.22, V.22bis, V.23, V.32, V.32bis, V.34 Rockwell V.FC
Fax Modulation Protocol	Unidentified
Error Correction/Compression	MNP10, V.42bis
Topology	Star
Wiring Type	Unshielded twisted pair
Boot ROM	128KB PROM

AUTO-RETRAIN - FALLBACK/FALLFORWARD
Type:	Configuration
Format:	AT [cmds] %E n [cmds]
Description:	Controls auto-retrain mode and fallback/fall forward.
Command	Function
%E0	Auto-retrain disabled
%E1	Auto-retrain enabled
%E2	Auto-retrain and Fallback/fall forward enabled
%E3	Auto-retrain and Fallback/fall forward with fast hang up enabled

BREAK SEND
Type:	Configuration
Format:	AT [cmds] \B n [cmds]
Default:	3
Range:	1-9
Unit:	.1 second
Description:	Sends break to modem

BREAK TYPE
Type:	Configuration
Format:	AT [cmds] \K n [cmds]
Description:	Configures action of break signal
Command	Break from DTE Reliable/Normal mode	Modem receives \B	Break from remote modem
\K0	Enter command mode, do not send break to remote modem.	Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to DTE.
\K1	Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to remote modem.	Buffers cleared and break sent to DTE.
\K2	Enter command mode, do not send break to remote modem.	Send break to remote modem immediately.	Send break to DTE immediately.
\K3	Send break to remote modem immediately.	Send break to remote modem immediately.	Send break to DTE immediately.
\K4	Enter command mode, do not send break to remote modem.	Send break to remote modem with transmitted data.	Break sent with received data to the DTE.
\K5	Send break with transmitted data.	Send break to remote modem with transmitted data.	Break sent with received data to the DTE.

CHANGE COUNTRY CODE
Type:	Configuration
Format:	AT [cmds] *NC nn [cmds]
Description:	Changes country code to one of 8 stored in NVRAM

COMPRESSION
Type:	Configuration
Format:	AT %C n
Description:	Selects data compression.
Command	Function
%C0	Data compression disabled
%C1	MNP5 enabled
%C2	V.42bis enabled
%C3	MNP5 and V.42bis enabled

COMPROMISE EQUALIZER
Type:	Configuration
Format:	AT [cmds] :E n [cmds]
Description:	Controls compromise equalizer
Command	Function
:E0	Equalizer disabled
:E1	Equalizer enabled

CONNECT MODE
Type:	Configuration
Format:	AT [cmds] \N n [cmds]
Description:	Sets connect mode
Command	Function
\N0	Normal mode enabled
\N1	Direct mode enabled
\N2	Reliable mode enabled
\N3	Auto-reliable mode enabled
\N4	LAPM mode only enabled
\N5	MNP mode only enabled

DISPLAY DELAYED NUMBERS
Type:	Immediate
Format:	AT [cmds] *B [cmds]
Description:	Displays list of delayed numbers

DISPLAY DELAYED NUMBERS
Type:	Immediate
Format:	AT [cmds *D [cmds]
Description:	Displays list of of delayed numbers

DISPLAY LINE SIGNAL LEVEL
Type:	Immediate
Format:	AT [cmds] %L [cmds]
Description:	Displays received line signal level in dBm

DISPLAY LINE SIGNAL QUALITY
Type:	Immediate
Format:	AT [cmds] %Q [cmds]
Description:	Displays line signal quality

DISPLAY SELECTED MODULATIONS
Type:	Immediate
Format:	AT [cmds] +MS? [cmds]
Description:	Displays active modes

DISPLAY SUPPORTED MODES
Type:	Immediate
Format:	AT [cmds] +MS=? [cmds]
Description:	Displays supported modes

DISPLAY STORED NUMBERS
Type:	Immediate
Format:	AT [cmds] \F [cmds]
Description:	Displays all stored phone numbers

FALL-BACK
Type:	Configuration
Format:	AT [cmds] -Q n [cmds]
Description:	Enables fall back to V.22/V.22bis
Command	Function
-Q0	V.22/V.22bis fall back enabled
-Q1	V.22/V.22bis fall back disabled

FLOW CONTROL
Type:	Configuration
Format:	AT [cmds] \G n [cmds]
Description:	Enables modem port flow control
Command	Function
\G0	Flow control disabled
\G1	Flow control enabled

MAXIMUM MNP BLOCK
Type:	Configuration
Format:	AT [cmds] \A n [cmds]
Description:	Sets the maximum transmission block size
Command	Function
\A0	MNP block size is 64 characters
\A1	MNP block size is 128 characters
\A2	MNP block size is 192 characters
\A3	MNP block size is 256 characters

MNP10 COMPRESSION
Type:	Configuration
Format:	AT [cmds] -K n [cmds]
Description:	Selects MNP10 data compression
Command	Function
-K0	MNP10 disabled
-K1	MNP10 enabled

MNP 10 HANDSHAKE
Type:	Configuration
Format:	AT [cmds] *H n [cmds]
Description:	Selects MNP 10 link negotiation speed
Command	Function
*H0	MNP 10 handshake at highest common speed
*H1	MNP 10 handshake at 1200bps
*H2	MNP 10 handshake at 4800bps

MNP STREAM/BLOCK MODE
Type:	Configuration
Format:	AT [cmds] \L n [cmds]
Description:	Selects the transfer mode for MNP
Command	Function
\L0	Stream mode for MNP enabled
\L1	Block mode for MNP enabled

MODULATION SELECTION
Type:	Configuration
Format:	AT [cmds] +MS= xx,y,zzz,aaa [cmds]
Description:	Sets options for active protocol. The transfer rates specified by z and a must be valid for the protocol selected.
Command	Function
x=0	V.21
x=1	V.22
x=2	V.22bis
x=3	V.23
x=9	V.32
x =10	V.32bis
x=11	V.34
x =64	Bell 103A
x =69	Bell 212A
x =74	V.FC
y =0	Automode disabled.
y =1	Auto-detect highest speed enabled.
z, a=300	Set minimum or maximum transfer rate at 300bps, respectively.
z, a =1200	Set minimum or maximum transfer rate at 1200bps, respectively.
z, a =2400	Set minimum or maximum transfer rate at 2400bps, respectively.
z, a =4800	Set minimum or maximum transfer rate at 4800bps, respectively.
z, a =7200	Set minimum or maximum transfer rate at 7200bps, respectively.
z, a =9600	Set minimum or maximum transfer rate at 9600bps, respectively.
z, a =12000	Set minimum or maximum transfer rate at 12000bps, respectively.
z, a =14400	Set minimum or maximum transfer rate at 14400bps, respectively.
z, a =16800	Set minimum or maximum transfer rate at 16800bps, respectively.
z, a =19200	Set minimum or maximum transfer rate at 19200bps, respectively.
z, a =21600	Set minimum or maximum transfer rate at 21600bps, respectively.
z, a =24000	Set minimum or maximum transfer rate at 24000bps, respectively.
z, a =26400	Set minimum or maximum transfer rate at 26400bps, respectively.
z, a =28800	Set minimum or maximum transfer rate at 28800bps, respectively.

PULSE DIAL CODE
Type:	Configuration
Format:	AT [cmds] *Z n [cmds]
Description:	Selects digit used for pulse dial code
Command	Function
*Z0	Use dial code 0
*Z1	Use dial code 1

S REGISTERS
Register	Function	Default
S14	Bit mapped	Unidentified
S16	Bit mapped test options	Unidentified
S20	Bit mapped	Unidentified
S21	Bit mapped V.24 options	Unidentified
S22	Bit mapped speaker options	Unidentified
S23	Bit mapped	Unidentified
S24	Sleep inactivity timer	0
S27	Bit mapped	Unidentified
S28	Bit mapped	Unidentified
S29	Flash modifier timer	0
S31	Bit mapped	Unidentified
S33	XOFF character	19
S40	Bit mapped	Unidentified
S41	Bit mapped	Unidentified
S201	Cellular transmit level	Unidentified