KATRON TECHNOLOGIES, INC.
ET-200T
|
NIC Type |
Ethernet |
|
Transfer Rate |
10Mbps |
|
Data Bus |
16-bit ISA |
|
Topology |
Star |
|
Wiring Type |
Unshielded twisted pair AUI transceiver via DB-15 port |
|
Boot ROM |
Available |
|
AUI ETHERNET VERSION | ||
|
Version |
JP1 | |
| » |
Version 2 |
Open |
|
Version 1 |
Closed | |
|
Note:The ethernet version is dependent on the MAU you are using. There should be some indication of the ethernet version on the MAU.
| ||
|
LINK INTEGRITY TEST | ||
|
Setting |
JP2 | |
| » |
Enabled |
Closed |
|
Disabled |
Open | |
|
Note:The link integrity test is only valid when the cable type is unshielded twisted pair. | ||
|
SEGMENT LENGTH | ||
|
Maximum Length |
JP3 | |
| » |
100 meters |
Pins 2 & 3 Closed |
|
150 meters |
Pins 1 & 2 Closed | |
|
Note:On this card segment length is the distance between the card and the hub. | ||
|
DATA BUS SPEED | ||
|
Bus Speed |
JP4 | |
| » |
6 - 8MHz (0 wait states) |
Open |
|
8 - 16MHz (1 wait state) |
Closed | |
|
INTERRUPT REQUEST | ||||||||
|
IRQ |
JP5A |
JP5B |
JP5C |
JP5D |
JP5E |
JP5F |
JP5G | |
|
2/9 |
Open |
Open |
Open |
Open |
Open |
Open |
Closed | |
| » |
3 |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
|
4 |
Open |
Open |
Open |
Open |
Closed |
Open |
Open | |
|
5 |
Open |
Open |
Open |
Closed |
Open |
Open |
Open | |
|
10 |
Open |
Open |
Closed |
Open |
Open |
Open |
Open | |
|
11 |
Open |
Closed |
Open |
Open |
Open |
Open |
Open | |
|
12 |
Closed |
Open |
Open |
Open |
Open |
Open |
Open | |
|
I/O BASE ADDRESS | |||||
|
Address |
JP6A |
JP6B |
JP6C |
JP6D | |
| » |
300h |
Open |
Open |
Open |
Closed |
|
320h |
Open |
Open |
Closed |
Open | |
|
340h |
Open |
Closed |
Open |
Open | |
|
360h |
Closed |
Open |
Open |
Open | |
|
BOOT ROM ADDRESS | ||||
|
Address |
JP7A |
JP7B |
JP7C |
JP7D |
|
C8000h |
Closed |
Open |
Closed |
Closed |
|
CC000h |
Open |
Open |
Closed |
Closed |
|
D0000h |
Closed |
Closed |
Open |
Closed |
|
D4000h |
Open |
Closed |
Open |
Closed |
|
D8000h |
Closed |
Open |
Open |
Closed |
|
DC000h |
Open |
Open |
Open |
Closed |
|
BOOT ROM | ||
|
Setting |
JP7E | |
| » |
Disabled |
Open |
|
Enabled |
Closed | |
|
BOOT ROM SIZE | |
|
Size |
JP8 |
|
8KB |
Pins 1 & 2 Closed |
|
16KB |
Pins 2 & 3 Closed |
|
CABLE TYPE | ||||
|
Type |
JP9A |
JP9B - JP9G |
JP9H | |
| » |
Unshielded twisted pair |
Closed |
Pins 2 & 3 closed |
Open |
|
AUI transceiver via DB-15 port |
Open |
Pins 1 & 2 closed |
Closed | |
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
LED1 |
Green |
On |
Collision detected on network |
|
LED1 |
Green |
Off |
Normal operation |
|
LED2 |
Yellow |
On |
Card is transmitting for an extended time |
|
LED2 |
Yellow |
Off |
Normal operation |
|
LED3 |
Green |
Blinking |
Data is being transmitted |
|
LED3 |
Green |
On |
Data is not being transmitted |
|
LED3 |
Green |
Off |
No power or card is faulty |
|
LED4 |
Yellow |
Blinking |
Data is being received |
|
LED4 |
Yellow |
On |
Data is not being received/TP network connection good |
|
LED4 |
Yellow |
Off |
No power, card is faulty, or TP network connection broken |
|
Note:If the link integrity test is disabled LED4 will not indicate twisted pair network connection status. | |||
