D-LINK
NETWORK ADAPTER (P/N D8611)
|
NIC Type |
D-Link Network, Proprietary |
|
Transfer Rate |
1Mbps |
|
Data Bus |
8-bit ISA |
|
Topology |
Linear bus |
|
Wiring Type |
Unshielded twisted pair |
|
Boot ROM |
Available |
|
NODE ADDRESS | ||||||||
|
Node |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
SW1/7 |
SW1/8 |
|
0 |
On |
On |
On |
On |
On |
On |
On |
On |
|
1 |
On |
On |
On |
On |
On |
On |
On |
Off |
|
2 |
On |
On |
On |
On |
On |
On |
Off |
On |
|
3 |
On |
On |
On |
On |
On |
On |
Off |
Off |
|
4 |
On |
On |
On |
On |
On |
Off |
On |
On |
|
251 |
Off |
Off |
Off |
Off |
Off |
On |
Off |
Off |
|
252 |
Off |
Off |
Off |
Off |
Off |
Off |
On |
On |
|
253 |
Off |
Off |
Off |
Off |
Off |
Off |
On |
Off |
|
254 |
Off |
Off |
Off |
Off |
Off |
Off |
Off |
On |
|
255 |
- |
- |
- |
- |
- |
- |
- |
- |
|
Notes: Node address 0 is used for messaging between nodes and must not be used. A total of 255 node address settings are available. The switches are a binary representation of the decimal node addresses. Switch 1 is the Least Significant Bit and switch 8 is the Most Significant Bit. The switches have the following decimal values: switch 1=128, 2=64, 3=32, 4=16, 5=8, 6=4, 7=2, 8=1. Turn off the switches and add the values of the off switches to obtain the correct node address. (On=0, Off=1) | ||||||||
|
INTERRUPT REQUEST | |||||
|
IRQ |
JP1A |
JP1B |
JP1C |
SW2/1 | |
| » |
2 |
N/A |
N/A |
N/A |
Off |
|
3 |
Closed |
Open |
Open |
On | |
|
4 |
Open |
Closed |
Open |
On | |
|
5 |
Open |
Open |
Closed |
On | |
|
Note:If the card is installed in a PC/AT compatible the IRQ should be IRQ5, IRQ3, or IRQ4. You should try the interrupts in that order. | |||||
|
ONBOARD TERMINATOR | |||
|
Setting |
JP2A |
JP2B | |
| » |
Disabled |
Open |
Closed |
|
Enabled |
Closed |
Open | |
|
Note:If the card is on either end of a linear bus network segment, the onboard terminator may be
| |||
|
BOOT ROM ADDRESS | ||||
|
Address |
Software Parameter |
JP3A |
JP3B | |
| » |
CC000 - CFFFFh |
HC |
Open |
Closed |
|
DC000 - DFFFFh |
HD |
Closed |
Open | |
|
Note:The software parameter is used in the DEVICE= statement in the CONFIG.SYS file (e.g. DEVICE = D-LINK.DRV /HC). | ||||
|
DMA CHANNEL | ||
|
Channel |
SW2/2 | |
| » |
DMA1 |
Off |
|
DMA3 |
On | |
|
I/O BASE ADDRESS | |||
|
Address |
SW2/3 |
SW2/4 | |
|
240h |
Off |
On | |
|
260h |
Off |
Off | |
|
340h |
On |
On | |
| » |
360h |
On |
Off |
|
BOOT ROM | ||
|
Setting |
SW2/6 | |
| » |
Disabled |
Open |
|
Enabled |
Closed | |
|
FACTORY CONFIGURED SETTINGS | |
|
Switch |
Setting |
|
SW2/5 |
Unused |
