ALTA RESEARCH CORPORATION
TOKENCOMBO-16 S/U (ISA)
|
NIC Type |
Token-Ring |
|
Transfer Rate |
4/16Mbps |
|
Data Bus |
16-bit ISA |
|
Topology |
Ring |
|
Wiring Type |
Unshielded twisted pair Shielded twisted pair (DB-9 port) |
|
Boot ROM |
Available |
|
COMPATIBILITY MODE |
||
|
Setting |
JP1 |
|
|
» |
Disabled |
Closed |
|
|
Enabled |
Open |
|
Note: If the system in which the card is to be installed is an 80286 using an older C & T or VLSI chipset and the card is not loading the network shell properly, compatibility mode should be enabled (JP1 open). On some revisions of this card, JP1 might not be present. |
||
|
BASE MEMORY ADDRESS |
|||||||
|
Address |
SW1/1 |
SW1/2 |
SW1/3 |
SW1/4 |
SW1/5 |
SW1/6 |
|
|
|
C0000h |
On |
Off |
Off |
Off |
Off |
Off |
|
|
C2000h |
On |
Off |
Off |
Off |
Off |
On |
|
|
C4000h |
On |
Off |
Off |
Off |
On |
Off |
|
|
C6000h |
On |
Off |
Off |
Off |
On |
On |
|
|
C8000h |
On |
Off |
Off |
On |
Off |
Off |
|
|
CA000h |
On |
Off |
Off |
On |
Off |
On |
|
» |
CC000h |
On |
Off |
Off |
On |
On |
Off |
|
|
CE000h |
On |
Off |
Off |
On |
On |
On |
|
|
D0000h |
On |
Off |
On |
Off |
Off |
Off |
|
|
DC000h |
On |
Off |
On |
Off |
Off |
On |
|
Note: If using two cards in the same system, the card set to secondary should use address DC000h as its default. |
|||||||
|
SHARED RAM SIZE |
|||
|
Size |
SW1/7 |
SW1/8 |
|
|
|
8KB |
Off |
Off |
|
» |
16KB |
Off |
On |
|
|
32KB |
On |
Off |
|
|
64KB |
On |
On |
|
INTERRUPT REQUEST |
|||
|
IRQ |
SW2/1 |
SW2/2 |
|
|
» |
2/9 |
Off |
Off |
|
|
3 |
Off |
On |
|
|
6 |
On |
Off |
|
|
7 |
On |
On |
|
NETWORK SEGMENT SPEED |
||
|
Speed |
SW2/3 |
|
|
» |
16Mbps |
On |
|
|
4Mbps |
Off |
|
Note: All cards on the network segment must have this option set identically. |
||
|
PRIMARY/ALTERNATE MODE |
|||
|
Setting |
Address |
SW2/4 |
|
|
» |
Primary |
A20h |
Off |
|
|
Alternate |
A24h |
On |
|
Note: If two cards are to be used in a single system, one of the cards must be set to primary and the other one must be set to alternate. |
|||
|
DIAGNOSTIC LED(S) |
|||
|
LED |
Color |
Status |
Condition |
|
LED1 |
Red |
On |
Data is being transmitted or received |
|
LED1 |
Red |
Off |
Data is not being transmitted or received |
|
MISCELLANEOUS NOTES |
|
The card automatically senses which network connector is being used. |
