BLACK BOX CORPORATION

5210E, LE031-C

NIC Type

Ethernet

Transfer Rate

10Mbps

Data Bus

8-bit ISA

Topology

Linear Bus

Wiring Type

RG-58A/U 50ohm coaxial

AUI transceiver via DB-15 port

Boot ROM

Available

INTERRUPT REQUEST

IRQ

JP1

JP2

JP3

JP4

JP5

JP6

»

2

Closed

Open

Open

Open

Open

Open

 

3

Open

Closed

Open

Open

Open

Open

 

4

Open

Open

Closed

Open

Open

Open

 

5

Open

Open

Open

Closed

Open

Open

 

6

Open

Open

Open

Open

Closed

Open

 

7

Open

Open

Open

Open

Open

Closed

I/O BASE ADDRESS

Address

JP7

JP8

JP9

JP10

JP11

JP12

 

200h

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

 

208h

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 1 & 2

 

210h

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 1 & 2

Pins 2 & 3

 

218h

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 1 & 2

Pins 1 & 2

 

350h

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

Pins 2 & 3

 

358h

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

Pins 1 & 2

»

360h

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

Pins 1 & 2

Pins 2 & 3

Pins 2 & 3

 

368h

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

 

370h

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 2 & 3

 

3E0h

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 2 & 3

Pins 2 & 3

 

3E8h

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

 

3F0h

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 2 & 3

 

3F8h

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Pins 1 & 2

Note: Pins designated should be in the closed position.

A full range of I/O addresses are available, in increments of 8h, from 200h to 3F0h for a total of 64 addresses. The 12 examples given are taken from the beginning (first four), the middle (middle four), and the end (last four) of the 64 addresses. To figure out the correct configuration for the I/O address you wish to use, subtract 200h from the address, divide the remainder by 08h, and convert the quotient to a 6-digit binary number. The binary number will represent the setting of each jumper. Each 0 represents pins 2 & 3 closed while each 1 represents pins 1 & 2 Closed. JP7 is the most significant bit (MSB) and JP12 is the least significant bit (LSB). For example, If the desired address is 228h; 228h - 200h = 28h, 28h /08h = 05h, 05h = 000101b, then the setting should be:

 

Address

JP7

JP8

JP9

JP10

JP11

JP12

 

228h

Pins 2 & 3

Pins 2 & 3

Pins 2 & 3

Pins 1 & 2

Pins 2 & 3

Pins 1 & 2

BASE MEMORY ADDRESS

Address

JP13

JP14

JP15

JP16

»

C0000h

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

 

C4000h

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

 

C8000h

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 2 & 3 Closed

 

CC000h

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 1 & 2 Closed

 

D0000h

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

 

D4000h

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

 

D8000h

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 1 & 2 Closed

Pins 2 & 3 Closed

 

DC000h

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 1 & 2 Closed

Pins 1 & 2 Closed

 

E0000h

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

 

E4000h

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

 

E8000h

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 2 & 3 Closed

 

EC000h

Pins 1 & 2 Closed

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Pins 1 & 2 Closed

EXPANSION MEMORY /BOOT ROM CONFIGURATION

Size

JP17

JP18

»

None

Pins 1 & 2 Closed

N/A

 

8KB RAM

Pins 2 & 3 Closed

Pins 2 & 3 Closed

 

Boot ROM

Pins 2 & 3 Closed

Pins 1 & 2 Closed

Note:The socket on the diagram labeled RAM/ROM can hold either a boot ROM chip or another 8KB RAM chip

CABLE TYPE

Type

W2 - W8

»

RG-58A/U 50ohm coaxial

2nd Setting

 

AUI transceiver via DB-15 port

1st Setting

Note:Refer to the diagram for the meanings of 2nd setting & 1st setting.

DATA BUS CONFIGURATION

Setting

WR27

»

Any slot other than slot 8 on a PC/XT

Open

 

Slot 8 on a PC/XT

Closed

Note:If installing this card in slot 8 of a PC/XT, you must close JP27. If card is not installed in a PC/XT or

Hosted by uCoz