QUATECH, INC.
ES100M/ES100MS/QS-100M/QS100MS
|
Category |
Serial controller |
|
Chipset Controller |
Unidentified 16550s |
|
I /O Options Supported |
Serial ports (QS-100 = 4, ES100 = 8) |
|
Maximum Onboard Memory |
N/A |
|
CONNECTIONS |
|||
|
Purpose |
Location |
Purpose |
Location |
|
Serial port 1 - RJ-11 |
CN1 |
Serial port 5 - RJ-11 |
CN5 |
|
Serial port 2 - RJ-11 |
CN2 |
Serial port 6 - RJ-11 |
CN6 |
|
Serial port 3 - RJ-11 |
CN3 |
Serial port 7 - RJ-11 |
CN7 |
|
Serial port 4 - RJ-11 |
CN4 |
Serial port 8 - RJ-11 |
CN8 |
|
Note:The QS-100 is equipped with 4 RJ-11 ports. |
|||
|
I/O ADDRESS CONFIGURATION |
||||||||||||
|
|
SW1 |
SW2 |
||||||||||
|
» |
Base Address |
1 |
2 |
3 |
4 |
5 |
6 |
1 |
2 |
3 |
4 |
5 |
|
» |
0300h |
On |
On |
On |
On |
On |
On |
Off |
Off |
On |
On |
On |
|
» |
On |
Off |
On |
Off |
Off |
On |
Off |
On |
Off |
Off |
On |
|
|
Note:The address range for the QS-100M/ES-100M is from 0 to FFFFh. The switches are a binary representation of the addresses. When a switch is off, the corresponding bit is set to 1 and has the following decimal value: SW1/1=8, SW1/2=4, SW1/3=2, SW1/4=1, SW1/5=8, SW1/6=4, SW2/1=2, SW2/2=1, SW2/3=8, SW2/4=4, SW2/5=2. SW2/5 is not used on the ES-100M. The QS-100M requires 32 consecutive address locations, and the ES-100M requires 64 consecutive address locations. |
||||||||||||
|
INPUT CLOCK FREQUENCY |
||
|
» Frequency |
J1 |
|
|
» |
1.8432MHz |
Pins 1 & 2, 4 & 5, 3 & 6 closed |
|
» |
18.432MHz |
Pins 2 & 5 closed |
|
» |
9.216MHz |
Pins 1 & 2, 5 & 6 closed |
|
» |
3.6864MHz |
Pins 2 & 3, 4 & 5 closed |
|
INTERRUPT STATUS REGISTER |
||
|
» Setting |
SW1/6 |
|
|
» |
Disabled (scratchpad register enabled) |
Off |
|
» |
Enabled |
On |
|
HANDSHAKE OPTIONS |
|
|
Setting |
J(2 - 9) |
|
RTS/CTS handshake, DTR/DSR loopback |
Pins 1 & 2, 4 & 5, 3 & 6 closed |
|
RTS/CTS loopback, DTR/DSR handshake |
Pins 1 & 4, 2 & 3, 5 & 6 closed |
|
RTS/CTS loopback, DTR/DSR loopback, AUXIN/AUXOUT loopback |
Pins 1 & 4, 2 & 5, 3 & 6 closed |
|
Note:J2 - J9 control the configurations of CN1 - CN8, respectively. Each RJ-11 port may be configured differently. |
|
|
INTERRUPT SELECT - J10 |
||||||||||||
|
IRQ |
A |
B |
C |
D |
E |
F |
G |
H |
I |
J |
K |
|
|
» |
IRQ3 |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
|
IRQ2 |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
|
IRQ4 |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
|
IRQ5 |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
|
IRQ6 |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
Open |
|
|
IRQ7 |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
Open |
|
|
IRQ10 |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
Open |
|
|
IRQ11 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
Open |
|
|
IRQ12 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
|
|
IRQ14 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
|
|
IRQ15 |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
|
CARRIER DETECT (DCD) SIGNAL INPUT |
||
|
» Setting |
J(11 - 18) |
|
|
» |
RJ-11 connected to chassis ground (DCD input disabled) |
Pins 1 & 2, 4 & 5 closed |
|
» |
DCD input enabled |
Pins 2 & 3, 5 & 6 closed |
Note:Pin 3 of the RJ-11 port must be connected to chassis ground or the DCD signal, depending on desired configuration. J11 - J18 control the configurations of CN1 - CN8, respectively. Each RJ-11 port may be configured differently. |
||
