AMERICAN DATA AQUISITION CORPORATION

5532DMA REV.0

Card Type

Data Aquisition

Chip Set

Unidentified

Maximum Onboard Memory

Unidentified

I/O Options

Analog input, digital input

Hard Drives supported

None

Floppy drives supported

None

Data Bus

8-bit ISA

Card Size

Half length

CONNECTIONS

Function

Label

50-pin analog/digital signals connector

J1

PORT A/B DMA CHANNEL SELECTION

Channel

W22

W23

W24

W28

W29

W30

1

Open

Open

Closed

Closed

Open

Open

2

Open

Closed

Open

Open

Closed

Open

3

Closed

Open

Open

Open

Open

Closed

Disabled

Open

Open

Open

Open

Open

Closed

PORT C/D DMA CHANNEL SELECTION

Channel

W25

W26

W27

W31

W32

W33

1

Open

Open

Closed

Closed

Open

Open

2

Open

Closed

Open

Open

Closed

Open

3

Closed

Open

Open

Open

Open

Closed

Disabled

Open

Open

Open

Open

Open

Closed

DIO PORT A CONFIGURATION

Function

Label

Position

 

8 bit input mode enabled

JP2

Pins 2 & 3 closed

 

16 bit input mode enabled

JP2

Pins 1 & 2 closed

»

Input enabled

W10

Closed

 

Output enabled

W10

Open

Note: In 16 bit mode, port A data is latched when port B data is latched.

DIO PORT B CONFIGURATION

Function

Label

Position

»

Input enabled

W11

Closed

 

Output enabled

W11

Open

»

IRQ interrupt disabled

W14

Open

 

IRQ interrupt enabled

W14

Closed

»

Handshaking output disabled

W35

Closed

 

Handshaking output enabled

W35

Open

»

Handshaking input disabled

W36

Closed

 

Handshaking input enabled

W36

Open

DIO PORT C CONFIGURATION

Function

Label

Position

 

8 bit input mode enabled

JP1

Pins 2 & 3 closed

 

16 bit input mode enabled

JP1

Pins 1 & 2 closed

»

Output enabled

W12

Open

 

Input enabled

W12

Closed

Note: In 16 bit mode, port C data is latched when port D data is latched.

DIO PORT D CONFIGURATION

Function

Label

Position

»

Output enabled

W13

Open

 

Input enabled

W13

Closed

»

IRQ interrupt disabled

W15

Open

 

IRQ interrupt enabled

W15

Closed

»

Handshaking output disabled

W34

Closed

 

Handshaking output enabled

W34

Open

»

Handshaking input disabled

W37

Closed

 

Handshaking input enabled

W37

Open

BASE I/O ADDRESS SELECTION

Setting

W9

W8

W7

W6

W5

W4

W3

 

000h

Open

Open

Open

Open

Open

Open

Open

 

008h

Open

Open

Open

Open

Open

Open

Closed

 

010h

Open

Open

Open

Open

Open

Closed

Open

 

018h

Open

Open

Open

Open

Open

Closed

Closed

 

020h

Open

Open

Open

Open

Closed

Open

Open

»

100h

Open

Closed

Open

Open

Open

Open

Open

 

3D8h

Closed

Closed

Closed

Closed

Open

Closed

Closed

 

3E0h

Closed

Closed

Closed

Closed

Closed

Open

Open

 

3E8h

Closed

Closed

Closed

Closed

Closed

Open

Closed

 

3F0h

Closed

Closed

Closed

Closed

Closed

Closed

Open

 

3F8h

Closed

Closed

Closed

Closed

Closed

Closed

Closed

Note: A total of 128 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. W9 is the Most Significant Bit and jumper W3 is the Least Significant Bit. The jumpers have the following decimal values:W9=512, W8=256, W7=128, W6=64, W5=32, W4=16, W3=8. Turn off the switches and add the values of the switches to obtain the correct memory address. (Close=1, Open=0)

IRQ INTERRUPT SELECTION

IRQ

W16

W17

W18

W19

W20

W21

 

IRQ2

Closed

Open

Open

Open

Open

Open

 

IRQ3

Open

Closed

Open

Open

Open

Open

 

IRQ4

Open

Open

Closed

Open

Open

Open

 

IRQ5

Open

Open

Open

Closed

Open

Open

 

IRQ6

Open

Open

Open

Open

Closed

Open

»

IRQ7

Open

Open

Open

Open

Open

Closed

Hosted by uCoz