ACQUTEK CORPORATION
PA-AD12(-H)
|
Card Type |
Data Acquisition |
|
Chip Set |
None |
|
Maximum Onboard Memory |
Unidentified |
|
I/O Options |
Analog/digital I/O |
|
Data Bus |
16-bit ISA |
|
Card Size |
Half-length |
|
CONNECTIONS |
|||
|
Function |
Label |
Function |
Label |
|
37-pin analog/digital signals connector |
CN1 |
A/D converter offset selector |
VR1 |
|
Timer signal input (8254) |
JP1 |
A/D converter range selector |
VR2 |
|
External clock input |
JP10 |
A/D converter CMRR selector |
VR3 |
|
USER CONFIGURABLE SETTINGS |
||
|
Function |
Label |
Position |
|
Differential A/D input |
JP9 |
Pins 1 & 2, 4 & 5 closed |
|
Single ended A/D input |
JP9 |
Pins 2 & 3, 5 & 6 closed |
|
TESTING JUMPER SETTINGS |
|||
|
Function |
Label |
Position |
|
|
» |
Factory configured - do not alter |
JP2 |
Pins 1 & 2, 3 & 4 closed |
|
» |
Factory configured - do not alter (S/H enabled) |
TP1 |
Pins 1 & 2 closed |
|
» |
Factory configured - do not alter |
TP2 |
Pins 1 & 2 closed |
|
» |
Factory configured - do not alter |
TP3 |
Pins 1 & 2 closed |
|
» |
Factory configured - do not alter |
TP4 |
Pins 1 & 2 closed |
|
» |
Factory configured - do not alter |
TP5 |
Pins 1 & 2 closed |
|
A/D INPUT VOLTAGE RANGE SELECTION |
|||
|
Function |
Label |
Position |
|
|
» |
5V A/D input |
JP5 |
Pins 2 & 3 closed |
|
|
10V A/D input |
JP5 |
Pins 1 & 2 closed |
|
» |
Bipolar A/D input |
JP6 |
Pins 1 & 2, 4 & 5 closed |
|
|
Unipolar A/D input |
JP6 |
Pins 2 & 3, 5 & 6 closed |
|
A/D INPUT GAIN SELECTION |
||
|
Gain |
JP8 |
|
|
|
Not installed |
Open |
|
» |
1 |
Pins 9 & 11 closed |
|
|
2 |
Pins 11 & 12 closed |
|
|
5 |
Pins 9 & 10 closed |
|
|
10 |
Pins 7 & 8 closed |
|
|
20 |
Pins 5 & 6 closed |
|
|
50 |
Pins 3 & 4 closed |
|
|
User defined |
Pins 1 & 2 closed |
|
BASE I/O ADDRESS SELECTION |
|||||||||
|
Setting |
JP7/A |
JP7/B |
JP7/C |
JP7/D |
JP7/E |
JP7/F |
JP7/G |
JP7/H |
|
|
|
000h |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
|
|
010h |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Open |
|
|
020h |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Open |
Closed |
|
|
030h |
Closed |
Closed |
Closed |
Closed |
Closed |
Closed |
Open |
Open |
|
|
040h |
Closed |
Closed |
Closed |
Closed |
Closed |
Open |
Closed |
Closed |
|
» |
2E0h |
Closed |
Closed |
Open |
Closed |
Open |
Open |
Open |
Closed |
|
|
FB0h |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
Open |
|
|
FC0h |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Closed |
|
|
FD0h |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
Open |
|
|
FE0h |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Closed |
|
|
FF0h |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
Open |
|
Note: A total of 256 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. JP7/A is the Most Significant Bit and switch JP7/H is the Least Significant Bit. The switches have the following decimal values: JP7/A=2048, JP7/B=1024, JP7/C=512, JP7/D=256, JP7/E=128, JP7/F=64, JP7/G=32, JP7/H=16. Turn off the switches and add the values of the switches to obtain the correct memory address. (Open=1, Closed=0) |
|||||||||
|
IRQ INTERRUPT SELECTION |
||||||
|
IRQ |
JP3/A |
JP3/B |
JP3/C |
JP3/D |
JP3/E |
|
|
|
IRQ2 |
Open |
Open |
Open |
Open |
Pins 1 & 2 |
|
|
IRQ3 |
Open |
Open |
Open |
Pins 1 & 2 |
Open |
|
|
IRQ4 |
Open |
Open |
Pins 1 & 2 |
Open |
Open |
|
» |
IRQ5 |
Open |
Pins 1 & 2 |
Open |
Open |
Open |
|
|
IRQ7 |
Pins 1 & 2 |
Open |
Open |
Open |
Open |
|
|
IRQ10 |
Open |
Open |
Open |
Open |
Pins 2& 3 |
|
|
IRQ11 |
Open |
Open |
Open |
Pins 2& 3 |
Open |
|
|
IRQ12 |
Open |
Open |
Pins 2& 3 |
Open |
Open |
|
|
IRQ14 |
Open |
Pins 2 & 3 |
Open |
Open |
Open |
|
|
IRQ15 |
Pins 2 & 3 |
Open |
Open |
Open |
Open |
|
|
Disabled |
Open |
Open |
Open |
Open |
Open |
|
Note: JP3 jumper may be labeled JP3/4 on the board. Pins designated are in the closed position. IRQ10, IRQ11, IRQ12, IRQ14 & IRQ15 are for AT compatible buses; PC buses will not support them. |
||||||
