PROMISE TECHNOLOGY, INC.
OCTET CONDUCTOR
|
Card Type |
Hard drive duplicator controller card |
|
Hard Drives supported |
One master EIDE/IDE drive (eight target EIDE/IDE drives) |
|
Floppy drives supported |
None |
|
Data Bus |
32-bit VESA Local Bus |
|
Card Size |
Full length, full-height card |
|
CONNECTIONS | |||
|
Function |
Location |
Function |
Location |
|
Primary connector to Octet Station via Cable1-IN |
J1 |
Reserved connector - do not use |
J4 |
|
Secondary connector to Octet Station via Cable2-IN |
J2 |
Reserved connector - do not use |
J5 |
|
Reserved connector - do not use |
J3 |
Reserved connector - do not use |
J6 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Label |
Position | |
| » |
Factory configured - do not alter |
J1 |
Pins 1 & 2 closed |
| » |
Factory configured - do not alter |
J2 |
Pins 1 & 2 closed |
| » |
Factory configured - do not alter |
J3 |
Pins 2 & 3 closed |
| » |
Factory configured - do not alter |
J4 |
Pins 2 & 3 closed |
| » |
Factory configured - do not alter |
J5 |
Pins 2 & 3 closed |
|
IRQ SELECTION (SECONDARY) | |||||
|
IRQ |
JP1 |
JP2 |
JP3 |
JP4 | |
|
10 |
Closed |
Open |
Open |
Open | |
| » |
11 |
Open |
Closed |
Open |
Open |
|
14 |
Open |
Open |
Closed |
Open | |
|
15 |
Open |
Open |
Open |
Closed | |
|
Note: Users are advised not to change the default jumper settings. | |||||
|
IRQ SELECTION (PRIMARY) | |||||
|
IRQ |
JP5 |
JP6 |
JP7 |
JP8 | |
|
10 |
Closed |
Open |
Open |
Open | |
|
11 |
Open |
Closed |
Open |
Open | |
| » |
14 |
Open |
Open |
Closed |
Open |
|
15 |
Open |
Open |
Open |
Closed | |
|
Note: Users are advised not to change the default jumper settings. | |||||
|
MISCELLANEOUS TECHNICAL INFORMATION |
|
The Octet Conductor controller provides the interface between host system and one Octet Station, where one master drive duplicates to eight target drives. |
OCTET STATION
|
CONNECTIONS | |||
|
Function |
Location |
Function |
Location |
|
Cable connector - master |
CN0 |
Cable connector - CABLE1-IN |
CN9 |
|
Cable connector - target1 |
CN1 |
Cable connector - CABLE2-IN |
CN10 |
|
Cable connector - target2 |
CN2 |
Start/stop button |
J2 |
|
Cable connector - target3 |
CN3 |
Power connectors - master |
J3 |
|
Cable connector - target4 |
CN4 |
Power connectors - target |
J4-J7 |
|
Cable connector - target5 |
CN5 |
Power switch |
J8 |
|
Cable connector - target6 |
CN6 |
Power supply |
J9 |
|
Cable connector - target7 |
CN7 |
Voltage selector |
J10 |
|
Cable connector - target8 |
CN8 | ||
|
DIAGNOSTIC LED(S) | |||
|
LED |
Color |
Status |
Condition |
|
LED1 |
Green |
On |
Target drive 1 is active |
|
LED1 |
Green |
Blinking |
Duplication error on target 1or no hard drive 1 |
|
LED1 |
Green |
Off |
Target drive 1 is idle |
|
LED2 |
Red |
On |
Power is on to target drives 1 & 2 |
|
LED2 |
Red |
Off |
Power is off to target drives 1 & 2 |
|
LED3 |
Green |
On |
Target drive 2 is active |
|
LED3 |
Green |
Blinking |
Duplication error on target 2 or no hard drive |
|
LED3 |
Green |
Off |
Target drive 2 is idle |
|
LED4 |
Green |
On |
Target drive 3 is active |
|
LED4 |
Green |
Blinking |
Duplication error on target 3 or no hard drive |
|
LED4 |
Green |
Off |
Target drive 3 is idle |
|
LED5 |
Red |
On |
Power is on to target drives 3 & 4 |
|
LED5 |
Red |
Off |
Power is off to target drives 3 & 4 |
|
LED6 |
Green |
On |
Target drive 4 is active |
|
LED6 |
Green |
Blinking |
Duplication error on target 4 or no hard drive |
|
LED6 |
Green |
Off |
Target drive 4 is idle |
|
LED7 |
Green |
On |
Target drive 5 is active |
|
LED7 |
Green |
Blinking |
Duplication error on target 5 or no hard drive |
|
LED7 |
Green |
Off |
Target drive 5 is idle |
|
LED8 |
Red |
On |
Power is on to target drives 5 & 6 |
|
LED8 |
Red |
Off |
Power is off to target drives 5 & 6 |
|
LED9 |
Green |
On |
Target drive 6 is active |
|
LED9 |
Green |
Blinking |
Duplication error on target 6 or no hard drive |
|
LED9 |
Green |
Off |
Target drive 6 is idle |
|
LED10 |
Green |
On |
Target drive 7 is active |
|
LED10 |
Green |
Blinking |
Duplication error on target 7 or no hard drive |
|
LED10 |
Green |
Off |
Target drive 7 is idle |
|
LED11 |
Red |
On |
Power is on to target drives 7 & 8 |
|
LED11 |
Red |
Off |
Power is off to target drives 7 & 8 |
|
LED12 |
Green |
On |
Target drive 8 is active |
|
LED14 |
Green |
Blinking |
Duplication error on target 8 or no hard drive |
|
LED12 |
Green |
Off |
Target drive 8 is idle |
|
LED13 |
Red |
On |
Power is on to master drive |
|
LED13 |
Red |
Off |
Power is off to master drive |
|
LED14 |
Green |
On |
Master drive is active |
|
LED14 |
Green |
Off |
Master drive is idle |
|
LED15 |
Red |
On |
Octet Station is on |
|
LED15 |
Red |
On |
Octet Station is off |
