Data bus:	32-bit, VL-bus
Size:	Three/quarter-length, full-height card
Hard drive supported:	Two IDE (AT) Interface drives
Floppy drives supported:	Two 360KB, 720KB, 1.2MB or 1.44MB drives

CONNECTIONS
Function	Location
34-pin control cable connector - floppy drive	J1
40-pin IDE(AT) Interface connector	J2
10-pin serial port 1 - internal	JP3
10-pin serial port 2 - internal	JP4
4-pin connector - drive active LED	JP7
25-pin parallel port - external	CN1

USER CONFIGURABLE SETTINGS
Function		Location	Setting
»	Parallel port is bi-directional	JP1	Open
	Parallel port is output only	JP1	Closed
»	Floppy controller enabled	JP2	pins 19 & 20 closed
	Floppy controller disabled	JP2	pins 20 & 21 closed

SERIAL PORT 1 CONFIGURATION
COM/Address		JP2
»	COM1/3F8h	pins 1 & 2, 5 & 6 closed
	COM3/3E8h	pins 2 & 3, 4 & 5 closed
	Disabled	pins 2 & 3, 5 & 6 closed

SERIAL PORT 2 CONFIGURATION
COM/Address		JP2
»	COM2/2F8h	pins 7 & 8, 11 & 12 closed
	COM4/2E8h	pins 8 & 9, 10 & 11 closed
	Disabled	pins 8 & 9, 11 & 12 closed

PARALLEL PORT CONFIGURATION
LPT/Address/IRQ		JP2
»	LPT1/378h/IRQ7	pins 13 & 14, 17 & 18, 23 & 24 closed
	LPT2/278h/IRQ5	pins 14 & 15, 16 & 17, 22 & 23 closed
	LPT3/3BCh/IRQ7	pins 13 & 14, 16 & 17, 23 & 24 closed
	Disabled	pins 14 & 15, 17 & 18 closed

HARD DRIVE SPEED
Speed		JP6
»	Speed 1	pins 2 & 3, 4 & 5 closed
	Speed 0	pins 1 & 2, 4 & 5 closed
	Speed 2	pins 2 & 3, 5 & 6 closed

EXTERNAL BIOS
Address		JP5
»	D8000h	pins 5 & 6, 7 & 8, 9 & 10 closed
	DE000h	pins 9 & 10 closed
	DC000h	pins 7 & 8, 9 & 10 closed
	DA000h	pins 5 & 6, 9 & 10 closed
	D8000h	pins 5 & 6, 7 & 8, 9 & 10 closed
	D6000h	pins 3 & 4, 9 & 10 closed
	D4000h	pins 3 & 4, 7 & 8, 9 & 10 closed
	D2000h	pins 3 & 4, 5 & 6, 9 & 10 closed
	D0000h	pins 3 & 4, 5 & 6, 7 & 8, 9 & 10 closed
	CE000h	pins 1 & 2, 9 & 10 closed
	CC000h	pins 1 & 2, 7 & 8. 9 & 10 closed
	CA000h	pins 1 & 2, 5 & 6, 9 & 10 closed
	C8000h	pins 1 & 2, 5 & 6, 7 & 8, 9 & 10 closed
	Disabled	all pins open
Note:JP5 should be left in the default setting unless an address conflict exists.