DATA TECHNOLOGY CORPORATION
DTC ULTIMA PRO (400576-89A)
|
Card Type |
Hard drive controller card |
|
Hard Drives supported |
Two IDE (AT) drives |
|
Floppy drives supported |
Two 360KB, 720KB, 1.2MB, or 1.44MB drives |
|
Data Bus |
16-bit ISA |
|
Card Size |
Half-length, full-height card |
|
CONNECTIONS | |||
|
Function |
Location |
Function |
Location |
|
9-pin serial port 1 - external |
CN1 |
16-pin game port |
J4 |
|
25-pin parallel port - external |
J1 |
34-pin cable connector - floppy drive |
J5 |
|
10-pin serial port 1 - internal |
J2 |
40-pin primary IDE(AT) connector |
J6 |
|
10-pin serial port 2 - internal |
J3 |
2-pin connector - drive active LED |
J7 |
|
USER CONFIGURABLE SETTINGS | |||
|
Function |
Label |
Position | |
| » |
BIOS setup enabled |
W2 |
Closed |
|
BIOS setup disabled |
W2 |
Open | |
| » |
Game port enabled |
W7 |
Pins 1 & 2 closed |
|
Game port disabled |
W7 |
Pins 2 & 3 closed | |
| » |
Serial port 2 enabled |
W12 |
Pins 1 & 2 closed |
|
Serial port 2 disabled |
W12 |
Pins 2 & 3 closed | |
| » |
Floppy drive interface enabled |
W15 |
Pins 1 & 2 closed |
|
Floppy drive interface disabled |
W15 |
Pins 2 & 3 closed | |
| » |
IDE interface enabled |
W16 |
Pins 1 & 2 closed |
|
IDE interface disabled |
W16 |
Pins 2 & 3 closed | |
| » |
Serial port 1 enabled |
W17 |
Pins 1 & 2 closed |
|
Serial port 1 disabled |
W17 |
Pins 2 & 3 closed | |
| » |
IDE primary address is 1F0h |
W20 |
Pins 1 & 2 closed |
|
IDE secondary address is 170h |
W20 |
Pins 2 & 3 closed | |
|
ECP DMA CHANNEL SELECTION | ||
|
Channel |
Label |
Position |
|
1 |
W1 |
Pins 5 & 6, 7 & 8 closed |
|
3 |
W1 |
Pins 1 & 2, 3 & 4 closed |
|
PARALLEL PORT MODE SELECTION | ||
|
Setting |
W11 |
W18 |
|
Disabled |
Pins 2 & 3 closed |
Pins 2 & 3 closed |
|
EPP |
Pins 2 & 3 closed |
Pins 1 & 2 closed |
|
Bi-directional/ ECP |
Pins 1 & 2 closed |
Pins 2 & 3 closed |
|
Uni-directional |
Pins 1 & 2 closed |
Pins 1 & 2 closed |
|
PARALLEL PORT ADDRESS SELECTION | |||
|
Setting |
Label |
Position | |
| » |
LPT1 (378h) |
W13 |
Pins 1 & 2 closed |
|
LPT2 (278h) |
W13 |
Pins 2 & 3 closed | |
|
SERIAL PORT 1 ADDRESS SELECTION | |||
|
Setting |
Label |
Position | |
| » |
COM1 (3F8h) |
W19 |
Pins 1 & 2 closed |
|
COM3 (3E8h) |
W19 |
Pins 2 & 3 closed | |
|
SERIAL PORT 2 ADDRESS SELECTION | |||
|
Setting |
Label |
Position | |
| » |
COM2 (2F8h) |
W14 |
Pins 1 & 2 closed |
|
COM4 (2E8h) |
W14 |
Pins 2 & 3 closed | |
|
BIOS ADDRESS SELECTION | |||
|
Address |
Location |
Position | |
| » |
C800h |
W3 |
Pins 1 & 3, 2 & 4 closed |
|
CC00 |
W3 |
Pins 3 & 5, 2 & 4 closed | |
|
D800 |
W3 |
Pins 1 & 3, 4 & 6 closed | |
|
DC00 |
W3 |
Pins 3 & 5, 4 & 6 closed | |
|
SERIAL PORT 1 INTERRUPT SELECTION | |||
|
IRQ |
Label |
Position | |
| » |
IRQ4 |
W10 |
Pins 2 & 3 closed |
|
IRQ5 |
W10 |
Pins 1 & 2 closed | |
|
Alternate |
W10 |
Open | |
|
SERIAL PORT 2 INTERRUPT SELECTION | |||
|
IRQ |
Label |
Position | |
| » |
IRQ3 |
W8 |
Pins 2 & 3 closed |
|
IRQ5 |
W8 |
Pins 1 & 2 closed | |
|
Alternate |
W8 |
Open | |
|
SERIAL PORT 1 ALTERNATE INTERRUPT SELECTION | ||
|
IRQ |
Label |
Position |
|
IRQ9 |
W5 |
Pins 1 & 3 closed |
|
IRQ10 |
W5 |
Pins 3 & 5 closed |
|
IRQ11 |
W5 |
Pins 2 & 4 closed |
|
IRQ12 |
W5 |
Pins 4 & 6 closed |
|
Note: W10 must be open to use alternate IRQs | ||
|
SERIAL PORT 2 ALTERNATE INTERRUPT SELECTION | ||
|
IRQ |
Label |
Position |
|
IRQ9 |
W4 |
Pins 1 & 3 closed |
|
IRQ10 |
W4 |
Pins 3 & 5 closed |
|
IRQ11 |
W4 |
Pins 2 & 4 closed |
|
IRQ12 |
W4 |
Pins 4 & 6 closed |
|
Note: W10 must be open to use alternate IRQs | ||
|
PARALLEL PORT INTERRUPT SELECTION | |||
|
IRQ |
Label |
Position | |
| » |
IRQ7 |
W9 |
Pins 2 & 3 closed |
|
IRQ5 |
W9 |
Pins 1 & 2 closed | |
|
IDE INTERRUPT SELECTION | ||
|
IRQ |
Label |
Position |
|
11 |
W6 |
Pins 4 & 6 closed |
|
12 |
W6 |
Pins 2 & 4 closed |
|
14 |
W6 |
Pins 3 & 5 closed |
|
15 |
W6 |
Pins 1 & 3 closed |
