3 3 8 7 S S SINGAPORE
Native| Translation
------+-----+-----+-----
Form 3.5"/HH Cylinders 4811| | |
Capacity form/unform 8700/ MB Heads | | |
Seek time / track 7.9/ ms Sector/track | | |
Controller SCSI3 SI/WI/ULTR/SC2 Precompensation
Cache/Buffer KB Landing Zone
Data transfer rate MB/S int Bytes/Sector 512
40.000 MB/S ext SYNC
Recording method operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C |
Power: sleep W Humidity % |
standby W Altitude km |
idle 14.0 W Shock g |
seek 17.0 W Rotation RPM 7200
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 650000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
MICROPL. 3387/4341/4345 SS NOTES ON INSTALLATION
+------OPTION-JUMPER---------------------------------------------+
| +-------------------1+ +-TEST-------+ |
| |::::: :: :::::::::| LED+ | :::::::::: | |
+----+--------------------+-------------++-+-FACTORY-ONLY--------+
| |
| |
+----------------------------------------------------------------+
**********************************************************************
J U M P E R S
**********************************************************************
MICROPL. 3387/4341/4345 SS NOTES ON INSTALLATION
Jumper Setting
==============
x = Factory default
Drive Option Selection
----------------------
+------------------- SP1
| +---------- ID2
| | +------- ID1
| | | +---- ID0
RESERVED RESERVED RESERVED | | | | +- Remote LED+
+--+-++-++-++-++-++--+--+-++--+--+-++--+--+-++-++-++-++
|35|33|31|29|27|25|23|21|19|17|15|13|11|09|07|05|03|01|
+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+--+
|36|34|32|30|28|26|24|22|20|18|16|14|12|10|08|06|04|02|
+-++--+--+--+--+--+-++-++--+-++-++--+-++-++--+--+--+-++
| | | | WP | | +- Remote LED-
| | | PTY | |
| | | | +------------- ID3
| | | +---------------- SP0
+--- RESERVED | +------------------------------- ALE
+---------------------------------- RESERVED
NOTE
Pin 4, 6, 8, 10, 12, 14, 16, 18, 22, and 24 are tied to Ground.
Option Jumper Block J2 is a 36-pin connector used for drive
addressing and various configuration options.
SCSI ID
-------
Jumpers at Pin 3-4, 5-6, 7-8, and 9-10 select the SCSI ID. Each SCSI
device on one Host Adapter must have a unique SCSI ID.
+----------+-------------------------------+
| SCSI ID | Jumper Location |
| | PINS |
| | ID3 | ID2 | ID1 | ID0 |
+----------+-------+-------+-------+-------+
| 0 | OPEN | OPEN | OPEN | OPEN | DEFAULT
+----------+-------+-------+-------+-------+
| 1 | OPEN | OPEN | OPEN | CLOSED|
+----------+-------+-------+-------+-------+
| 2 | OPEN | OPEN | CLOSED| OPEN |
+----------+-------+-------+-------+-------+
| 3 | OPEN | OPEN | CLOSED| CLOSED|
+----------+-------+-------+-------+-------+
| 4 | OPEN | CLOSED| OPEN | OPEN |
+----------+-------+-------+-------+-------+
| 5 | OPEN | CLOSED| OPEN | CLOSED|
+----------+-------+-------+-------+-------+
| 6 | OPEN | CLOSED| CLOSED| OPEN |
+----------+-------+-------+-------+-------+
| 7 | OPEN | CLOSED| CLOSED| CLOSED|
+----------+-------+-------+-------+-------+
| 8 | CLOSED| OPEN | OPEN | OPEN |
+----------+-------+-------+-------+-------+
| 9 | CLOSED| OPEN | OPEN | CLOSED|
+----------+-------+-------+-------+-------+
| 10 | CLOSED| OPEN | CLOSED| OPEN |
+----------+-------+-------+-------+-------+
| 11 | CLOSED| OPEN | CLOSED| CLOSED|
+----------+-------+-------+-------+-------+
| 12 | CLOSED| CLOSED| OPEN | OPEN |
+----------+-------+-------+-------+-------+
| 13 | CLOSED| CLOSED| OPEN | CLOSED|
+----------+-------+-------+-------+-------+
| 14 | CLOSED| CLOSED| CLOSED| OPEN |
+----------+-------+-------+-------+-------+
| 15 | CLOSED| CLOSED| CLOSED| CLOSED|
+----------+-------+-------+-------+-------+
SP0/SP1 Spindle Control Option
-------------------------------
SP0 CLOSED
SP1 OPEN Spindle motor starts when START UNIT command is
received.
SP0 OPEN (default)
SP1 OPEN Spindle motor starts at power-on.
SP0/SP1 Spindle Delay Option
-----------------------------
SP1 CLOSED
SP0 OPEN Spindle motor start-up is delayed based on SCSI ID (12
seconds per ID).
SP1 OPEN (default)
SP0 OPEN Spindle motor starts at power on.
WP Write Protect Option
------------------------
WP CLOSED Drive is write protected.
WP OPEN Drive is not write protected. (default)
PTY Bus Parity Check Option
----------------------------
PTY CLOSED Drive neither generates nor detects parity.
OPEN Drive generates parity and has parity detection
enabled. (default)
Remote LED
----------
Open Collector output - Used to drive a user-supplied LED to indicate
the drive as active.
Activity LED Enable ALE
-----------------------
ALE CLOSED Interface ACTIVITY LED OUT signal is enabled
(default)
OPEN Interface ACTIVITY LED OUT signal is disabled
