S D - 3 2 4 0 - 3 0 TEAC
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 1930| | |
Capacity form/unform 249/ MB Heads 4| | |
Seek time / track 17.0/ 7.0 ms Sector/track 62| | |
Controller IDE / AT Precompensation
Cache/Buffer 64 KB READ-AHEAD Landing Zone
Data transfer rate 2.500 MB/S int Bytes/Sector 512
4.000 MB/S ext
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 50 | -40 60
Power: sleep 0.1 W Humidity % 8 80 | 8 80
standby 0.5 W Altitude km |
idle 3.2 W Shock g 5 | 70
seek 5.1 W Rotation RPM 3600
read/write 3.4 W Acoustic dBA 45
spin-up W ECC Bit
MTBF h 100000
Warranty Month
Lift/Lock/Park YES Certificates CSA,TUV,UL478
**********************************************************************
J U M P E R S
**********************************************************************
TEAC SD-3240-30 HARD DISK DRIVE SPECIFICATION 10530648-01
Jumper Setting
==============
Indicator LED
-------------
The indicator (LED) on the front bezel lights up while the HDD
executes a command. An external LED can also be lighted through the
-SLV/ACT signal terminal on the same condition by setting the strap
S0 to ON.
Straps
------
The setting method for the straps, S2 and S3, should be changed
according to the number of the HDDs connected as shown in the
following table.
Functions of straps
+----------+-------------------------------------------------------+
| Strap No.| Function |
+----------+-------------------------------------------------------+
| SP | Changes over the function of the -SLV/ACT output |
| | signal. |
| | ON : The -ACTIVE signal is selected. The external LED|
| | can be lighted up at the -SLV/ACT signal |
| | terminal. |
| | OFF : The -SLAVE PRESENT signal is selected. |
+----------+-------------------------------------------------------+
| S0 | (Not used) |
+----------+-------------------------------------------------------+
| S1 | Changes over the -I/O CH RDY output signal. |
| | OFF : The -I/O CH RDY signal is not output. |
| | ON : The -I/O CH RDY signal is output. |
+----------+-------------------------------------------------------+
| S2 | Selects the master drive or slave drive. |
| | OFF : Only one unit used, or master drive with two |
| | units used. |
| | ON : Slave drive with two units used. |
+----------+-------------------------------------------------------+
| S3 | Selects whether one HDD is used singly, or two HDDs |
| | are used in daisy chain connection. |
| | ON : Two HDDs are used. |
| | OFF : Only one HDD is used. |
+----------+-------------------------------------------------------+
Notes: 1. ON : Strap short
OFF : Strap open
2. At the shipping of the HDD, the strap SP is set to ON, S0
to OFF, S1 to OFF, S2 to OFF, S3 to OFF.
How to set the straps, S2 and S3
--------------------------------
+-------------------------+--------------+-----+-----+
|Number of HDDs connected | Master/Slave | S2 | S3 |
+-------------------------+--------------+-----+-----+
| 1 | - | OFF | OFF |
+-------------------------+--------------+-----+-----+
| 2 | Master | OFF | ON |
| | Slave | ON | ON |
+-------------------------+--------------+-----+-----+
**********************************************************************
I N S T A L L
**********************************************************************
TEAC SD-3210-00/3240-00/30
Notes on Installation
=====================
Drive Orientation
-----------------
The head assembly uses a rotary actuator that provides circular arc
head motion about the support point. This keeps the drive well-
balanced and allows it to be installed in virtually any physical
orientation.
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
Screws
------
3-#6-32UNC 4 deep each side.
4-#6-32UNC 4 deep bottom.
Auto shipping lock function
---------------------------
The auto shipping lock is designed to protect the media against the
risk of damage due to vibration and shock during transport. When the
power is turned off, the head carriage is locked automatically at the
shipping zone, within the inside limit of the work zone, to protect
your important stored data.
Automatic self-diagnosis
------------------------
When the power is switched on, the SD-3210 and SD-3240 automatically
performs a selfcheck sequence, checking program ROM, buffer RAM, and
interface register.
