S D - 3 2 1 0 - 3 0 TEAC
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 1695| 1024| |
Capacity form/unform 215/ MB Heads 4| 8| |
Seek time / track 17.0/ 7.0 ms Sector/track 62| 57| |
Controller IDE / AT Precompensation
Cache/Buffer 64 KB LOOK-AHEAD Landing Zone
Data transfer rate 2.500 MB/S int Bytes/Sector 512
4.000 MB/S ext
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 50 | -40 60
Power: sleep 0.1 W Humidity % 8 80 | 8 80
standby 0.5 W Altitude km |
idle 3.2 W Shock g 5 | 70
seek 5.1 W Rotation RPM 3600
read/write 3.4 W Acoustic dBA 45
spin-up W ECC Bit
MTBF h 100000
Warranty Month
Lift/Lock/Park YES Certificates CSA,TUV,UL478
**********************************************************************
L A Y O U T
**********************************************************************
TEAC SD-3210-30 HARD DISK DRIVE SPECIFICATION 10530648-00 REV. B
+---------------------------------------------------------++-+Strap
| || |SP
| |+-+S0 3
| |1X
| |XX Inter-
| |XX face
| |XX
| |XX
| |XX
|++LED |XX
|++ |XX
| |XX
| |xx
| |XX Power
| |
| |XX Power
| |XX
+---------------------------------------------------------+
**********************************************************************
J U M P E R S
**********************************************************************
TEAC SD-3210-30 HARD DISK DRIVE SPECIFICATION 10530648-00 REV. B
Jumper Setting
==============
Indicator LED
-------------
The indicator (LED) on the front bezel lights up while the HDD
executes a command. An external LED can also be lighted through the
-SLV/ACT signal terminal on the same condition by setting the strap
SP to ON.
Straps
------
The setting method for the straps, S2 and S3, should be changed
according to the number of the HDDs connected as shown in the
following table.
Functions of straps
+----------+-------------------------------------------------------+
| Strap No.| Function |
+----------+-------------------------------------------------------+
| SP | Changes over the function of the -SLV/ACT output |
| | signal. |
| | ON : The -ACTIVE signal is selected. The external LED|
| | can be lighted up at the -SLV/ACT signal |
| | terminal. |
| | OFF : The -SLAVE PRESENT signal is selected. |
+----------+-------------------------------------------------------+
| S0 | (Not used) |
+----------+-------------------------------------------------------+
| S1 | Changes over the -I/O CH RDY output signal. |
| | OFF : The -I/O CH RDY signal is not output. |
| | ON : The -I/O CH RDY signal is output. |
+----------+-------------------------------------------------------+
| S2 | Selects the master drive or slave drive. |
| | OFF : Only one unit used, or master drive with two |
| | units used. |
| | ON : Slave drive with two units used. |
+----------+-------------------------------------------------------+
| S3 | Selects whether one HDD is used singly, or two HDDs |
| | are used in daisy chain connection. |
| | ON : Two HDDs are used. |
| | OFF : Only one HDD is used. |
+----------+-------------------------------------------------------+
Notes: 1. ON : Strap short
OFF : Strap open
2. At the shipping of the HDD, the strap SP is set to ON, S0
to OFF, S1 to OFF, S2 to OFF, S3 to OFF.
How to set the straps, S2 and S3
--------------------------------
+-------------------------+--------------+-----+-----+
|Number of HDDs connected | Master/Slave | S2 | S3 |
+-------------------------+--------------+-----+-----+
| 1 | - | OFF | OFF |
+-------------------------+--------------+-----+-----+
| 2 | Master | OFF | ON |
| | Slave | ON | ON |
+-------------------------+--------------+-----+-----+
**********************************************************************
I N S T A L L
**********************************************************************
TEAC SD-3210-30 HARD DISK DRIVE SPECIFICATION 10530648-00 REV. B
Notes on Installation
=====================
Installation direction
----------------------
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
Any of the four directions can be used.
The mounting cabinet for the HDD should be constructed so that no
distortion may be produced in the chassis.
A space of at least 1.5mm must be allowed between the mounting
cabinet and the PCBA of the HDD.
An insulation sheet should be stuck to the PCBA mounting face of the
HDD mounting cabinet, as required.
In each mounted position, the front can be raised by up to 30*.
Mounting positions other than those shown must be discussed
separately.
Screws
------
The HDD is fixed with screws through the mounting holes at the
3-#6-32UNC 4 deep each side.
4-#6-32UNC 4 deep bottom.
Auto shipping lock function
---------------------------
The auto shipping lock is designed to protect the media against the
risk of damage due to vibration and shock during transport. When the
power is turned off, the head carriage is locked automatically at the
shipping zone, within the inside limit of the work zone, to protect
your important stored data.
Automatic self-diagnosis
------------------------
When the power is switched on, the SD-3210 and SD-3240 automatically
performs a selfcheck sequence, checking program ROM, buffer RAM, and
interface register.
