S D - 3 2 1 0 - 0 0 TEAC
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 1695| | |
Capacity form/unform 215/ MB Heads 4| | |
Seek time / track 17.0/ 7.0 ms Sector/track 62| | |
Controller SCSI1 SINGLE-ENDED Precompensation
Cache/Buffer 64 KB LOOK-AHEAD Landing Zone
Data transfer rate 2.500 MB/S int Bytes/Sector 512
4.000 MB/S ext SYNC
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 50 | -40 60
Power: sleep 0.1 W Humidity % 8 80 | 8 80
standby 0.5 W Altitude km |
idle 3.2 W Shock g 5 | 70
seek 5.1 W Rotation RPM 3600
read/write 3.4 W Acoustic dBA 45
spin-up W ECC Bit
MTBF h 100000
Warranty Month
Lift/Lock/Park YES Certificates CSA,TUV,UL478
**********************************************************************
J U M P E R S
**********************************************************************
TEAC SD-3210-00 3.5-IN. HARD DISK DRIVE SPECIFICATION 10530646-00
Jumper Setting
==============
The SCSI ID shall be set with the individual straps of SP, S0, S1,
and S2 on the PCBA.
The SP strap is to reserve the setting logic for S0, S1 and S2.
+----------+---------------+----------------+
| | SP=ON | SP=OFF |
+----------+---------------+----------------+
|SCSI ID | S2 S1 S0 | S2 S1 S0 |
+----------+---------------+----------------+
| 0 | ON ON ON | OFF OFF OFF |
+----------+---------------+----------------+
| 1 | ON ON OFF | OFF OFF ON |
+----------+---------------+----------------+
| 2 | ON OFF ON | OFF ON OFF |
+----------+---------------+----------------+
| 3 | ON OFF OFF | OFF ON ON |
+----------+---------------+----------------+
| 4 | OFF ON ON | ON OFF OFF |
+----------+---------------+----------------+
| 5 | OFF ON OFF | ON OFF ON |
+----------+---------------+----------------+
| 6 | OFF OFF ON | ON ON OFF |
+----------+---------------+----------------+
| 7 | OFF OFF OFF | ON ON ON |
+----------+---------------+----------------+
Note: The strap states are as follows:
1: Strap open
2: Strap short
**********************************************************************
I N S T A L L
**********************************************************************
TEAC SD-3210-00/3240-00/30
Notes on Installation
=====================
Drive Orientation
-----------------
The head assembly uses a rotary actuator that provides circular arc
head motion about the support point. This keeps the drive well-
balanced and allows it to be installed in virtually any physical
orientation.
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
Screws
------
3-#6-32UNC 4 deep each side.
4-#6-32UNC 4 deep bottom.
Auto shipping lock function
---------------------------
The auto shipping lock is designed to protect the media against the
risk of damage due to vibration and shock during transport. When the
power is turned off, the head carriage is locked automatically at the
shipping zone, within the inside limit of the work zone, to protect
your important stored data.
Automatic self-diagnosis
------------------------
When the power is switched on, the SD-3210 and SD-3240 automatically
performs a selfcheck sequence, checking program ROM, buffer RAM, and
interface register.
