S Q 3 2 7 0 A SYQUEST
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/HH Cylinders | 1024| |
Capacity form/unform 256/ MB Heads 2| 16| |
Seek time / track 14.5/ 3.0 ms Sector/track | 32| |
Controller IDE / AT Precompensation
Cache/Buffer 128 KB Landing Zone
Data transfer rate 4.000 MB/S int Bytes/Sector 512
MB/S ext
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 4 55 | -40 70
Power: sleep 0.6 W Humidity % 8 90 |
standby W Altitude km -0.305 3.048| -0.305 12.192
idle 1.5 W Shock g 3 | 50
seek 4.5 W Rotation RPM 3600
read/write 3.5 W Acoustic dBA 45
spin-up W ECC Bit
MTBF h 100000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
SYQUEST SQ3270A INSTALLATION
+---------------------------------------------------------+
| |XX 3-PIN
| |xx POWER
| |XXI
| Jumper |XXN
| +-+ |XXT
| | | |XXE
| +-+ |XXR
| |XXF
| |XXA
| |XXC
| |XXE
| |XX
| |XX
| |
| |XX POWER
| |XX
+---------------------------------------------------------+
**********************************************************************
J U M P E R S
**********************************************************************
SYQUEST SQ3270A INSTALLATION
Jumper Setting
==============
...X
MASTER ...X1
SLAVE ...o
...o
ACKNOWLEDGE
MEDIA CHANGE
X...
X...
NO MEDIA CHANGE
MOTIVICATION
o...
o...
**********************************************************************
I N S T A L L
**********************************************************************
SYQUEST SQ3270A INSTALLATION
Notes On Installation
=====================
Drive mounting
--------------
horizontally vertically
+-----------------+ +--+ +--+ +------------------+
| | | +-----+ +-----+ | | | x
| | | | | | | | x+----------------+x
+-+-----------------+-+ | | | | | | ||x x||
+---------------------+ | | | | | | || x x ||
| | | | | | || x x ||
x x | | | | | | || x x ||
+------x------x-------+ | +-----+ +-----+ | || xx ||
+-+------x--x-------+-+ +--+ +--+ || x x ||
| xx | || x x ||
| x x | || x x ||
+---x--------x----+ |x x|
x x x++----------------++x
UNACCEPTABLE! UNACCEPTABLE!
Never install PC board on the Top!
For best results, the cartridges should be formatted in the same
position as the final (predominatly) mounted orientation.
Screw Configuration
-------------------
Bottom Mounting: 6-32 UNC (or M4) screws, 4 places. Maximum length
into drive frame: 0.20-inch (5.08 mm)
Side Mounting: 6-32 UNC (or M4) screws, 4 places. Maximum length
into drive frame: 0.13-inch (3.30 mm)
3-PIN 4-PIN
+---+ +---------------------+ +----+
|OOO+-+ oooooooooooooooooooo+-+OOOO|
+---+ | ooooooooo oooooooooo| +----+
POWER +---------------------+ POWER
Pin 1 = +5V Pin 1 = +5V
2 = NC 2 = GND
3 = GND 3 = NC
4 = NC (Not connected)
**********************************************************************
F E A T U R E S
**********************************************************************
SYQUEST SQ3270A INSTALLATION
READ BEFORE YOU BEGIN...
The SQ3270A is an ATA compatible drive.
Observe static-discharge precautions: Keep the drive in its static-
shielded bag until you are ready to complete the installation.
- Do not touch the PC Board or I/O connector pins.
- Always handle the drive by the edge or frame. Never apply pressure
to the PC Board or the top cover.
Use a grounded wrist strap at your workstation; if unavailble, ground
yourself frequently by touching the metal chassis of the system
before handling any components. Provide anti-static padding on all
work surfaces. Avoid static inducing carpeted areas.
Drive Configuration
-------------------
The user must select the drive features that are appropriate for
installation in their system. This is done by way of configuration
jumpers found on the drive PC Board.
CMOS Configuration (ATA Systems)
--------------------------------
Basic information about the drive must be entered in the host system
CMOS. The number of heads, cylinders and sectors per track are
specific to each drive and collectively define the drives "geometry".
CMOS configuration is system dependent and is usually accomplished
through a keystroke or combination of keystrokes during the POWER-ON
sequence or a utility such as setup after the system has booted.
Default Drive Geometry
----------------------
SyQuest ATA interface drives translate their physical drive
geometry's. If the drive types offered by the CMOS does not support
the numbers of cylinders, heads and sectors and your system does not
include a "user-defined" drive type, then select a drive type which
is less than or equal to the capacity given in the "Capacity"
section.
