K L - 3 1 0 0 O C T A G O N I I KALOK
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/HH Cylinders | 979| |
Capacity form/unform 105/ 120 MB Heads | 6| |
Seek time / track 25.0/ 5.0 ms Sector/track | 35| |
Controller IDE / AT Precompensation
Cache/Buffer 32 KB STATIC RAM Landing Zone
Data transfer rate 1.250 MB/S int Bytes/Sector 512
MB/S ext
Recording method RLL 2/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 10 55 | -40 60
Power: sleep W Humidity % 8 80 | 5 90
standby W Altitude km -0.305 3.048| -0.305 9.000
idle 8.2 W Shock g 8 | 40
seek 10.4 W Rotation RPM 3662
read/write W Acoustic dBA 40
spin-up W ECC Bit
MTBF h 100000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
KALOK KL3100 OEM MANUAL VER. 2.0, 16/JULY/1991 P/N 86009-001 A
+---------------------------------------------------------+ 12V
| |XXGND
| Power |XXGND
| | 5V
| |1X
| |XX I
| |XX N
| |XX T
| |XX E
| |X* R
| |XX F
| |XX A
| |XX C
| |XX E
| |XX
| |+-+
| Jumper|| |
| || |M/S
+---------------------------------------------------------++-+
**********************************************************************
J U M P E R S
**********************************************************************
KALOK KL3100 OEM MANUAL VER. 2.0, 16/JULY/1991 P/N 86009-001A
Jumper Setting
==============
GND 40 Pin IDE Connector
12VDC | 5VDC | M/S
| +++ | +-----------------+-------------------+ +-+-+
+-------+---------------------------------------------------+
|Power |O O O O O O O O O O O O O O O O O O O O O O O O|
|O O O O|1 O O O O O O O O O O O O O O O O O O O O O O O O|
+-------+---------------------------------------------------+
-------+
Single Drive in a System O O O |M/S
(Factory Setting) O O xxx |
-----------+
-------+
Master Drive in a two X O O |M/S
drive system O X O O |
-----------+
-------+
Slave Drive in a two O X O |M/S
drive system O O X O |
-----------+
X = CLOSED
Two drive system: Drive 1 must be MASTER
Drive 2 must be SLAVE
Master/Slave Daisy-Chain Configuration
--------------------------------------
The KL3100 disk drive ships with one jumper installed in the jumper
block header. The jumper is across the top outside pins. This jumper
selects a single drive installation. The single drive is Drive 0
(Fixed disk 1 in the system BIOS setup or C:). For a single AT/IDE
hard disk drive installation, leave the jumper in the header across
these pins. All jumpers removed also works for a single drive
installation.
For a dual drive daisy-chain installation, the master drive is Drive
0 (fixed disk 1 in BIOS setup or C:). The master drive must have pin
pair Master of the jumper block header jumpered. The slave drive is
Drive 1 (fixed disk 2 in BIOS setup or D:). The slave must have pin
pair Slave of jumper block jumpered. Install no other jumpers in
jumper block on the KL3100 disk drive. There should be only one
jumper installed per drive. Some mixed vendor master/slave sual drive
configurations may not be compatible.
**********************************************************************
I N S T A L L
**********************************************************************
KALOK KL3100 OEM MANUAL VER. 2.0, 16/JULY/1991 P/N 86009-001 A
Notes On Installation
=====================
Drive and Host Adapter Installation
-----------------------------------
This chapter provides configuration and installation instructions for
the Kalok KL3100/AT hard disk drive. Before installing the hard disk,
you must first disconnect your AT computer system from AC power out-
lets.
Required Disk Subsystem Parts
-----------------------------
1. Kalok KL3100/AT hard disk drive P/N 73003-001
2. Kalok 5.25" mounting brackets P/N 83003-001 (black)
and faceplate P/N 83003-002 (grey)
3. Kalok 3.5" faceplate P/N 83001-001 (black)
P/N 83001-002 (grey)
4. 40-pin AT/IDE hard disk cable Supplied with the Host adapter
5. 34-pin floppy disk drive cable Supplied with the Host adapter
6. Not supplied with Kalok mounting kits, are four standard 6-32
screws.
The KL3100 needs the 6-32 screws to mount the drive. The drive mounts
with the threaded holes on the bottom or sides. If needed, the AT-
style sidemount rails attach to the Kalok 5.25" mounting brackets.
Select screw lengths that limit screw penetration into the mounting
brackets to 0.13 inches (3.3 mm) max.
Notes:
1. In many new AT system cases, 3.5" internal mounting options are
available. Some AT cases designs, need AT-style side-mount rails.
2. Embedded AT/IDE systems don't need the PC/AT host adapters. Non-
embedded AT/IDE systems need a host adapter.
Required Host adapter formatting/Partitioning Software
------------------------------------------------------
1. To format and partition the disk, you need a bootable DOS diskette
version 3.31 or higher. You also need the DOS utilities FDISK and
FORMAT programs, in the same DOS version.
Interface Connector Part Numbers
--------------------------------
P1: AT/IDE Task File (40-pin) Molex 40312 or 3M 3417
P2: Power Supply (4-pin) Molex 8981-4P housing
Molex 8980-3 contacts
AMP 1-480424-0 housing
AMP 60617 contacts
P8: Drive HDA ground (1-pin) Molex 187 quick disconnect
AMP 62137 quick disconnect
Install a Plug to pin 20 on P1. This will prevent an incorrect
connection of J1 and P1. Removal of pin 20 of J1 is an industry
standard from.
AT/IDE Cable Connections
------------------------
Cable connections between the host adapter or the host system should
use 28 AWG stranded flat cable, 3M 3365-40, or equivalent. The cable
length should not exceed 2 feet.
**********************************************************************
F E A T U R E S
**********************************************************************
KALOK KL3100 OEM MANUAL VER. 2, 16/JULY/1991 P/N 86009-001 A
General Description
-------------------
The KL3100 Winchester disk drive is a storage device for a computer
system with the industry standard PC/AT or AT/IDE interface.
The KL3100 has a formatted capacity of 105.2 megabytes. It uses a
rotary band positioner driven by a bipolar stepper motor. The stepper
has microstepping error recovery and a feedback sensor. The disk
drive operates under the control of a microprocessor to position the
read/write heads. The head positioning mechanism design assures that
the thermal loops of the positioning system oppose each other. This
results in extremely accurate head positioning over the entire
operating range.
The KL3100 has a magnetic fluid seal. This eliminates spindle motor
bearing contamination. The recirculating filter at the periphery of
the disks efficiently cleans the head/disk assembly (HDA) air. The
filter traps entrained particles.
Seek Time
---------
+----------------------------------+--------+
| | 3012 |
+----------------------------------+--------+
|Track-to-Track msec. typ. | 5 |
+----------------------------------+--------+
|One-Third Stroke msec. | 25 |
|True average seek msec. | 25 |
+----------------------------------+--------+
|Full stroke seek msec. | 50 |
+----------------------------------+--------+
|Latency msec. avg. | 8.19 |
+----------------------------------+--------+
Drive Formatting
----------------
The KL3100 is factory formatted. The KL3100/AT drive uses cylinder/
head skewing to improve data throughput performance. The format and
skewing features of the drive are transparent to the user. Altering
the Format during use is not possible.
WARNING
Remove the Yellow shipping tape from the drive before you apply
power.
