P A L L A D I U M P 1 0 0 0 - 2 A F JTS CORP.
Native| Translation
------+-----+-----+-----
Form 3.5"/SUPERSLIMLINE Cylinders 4629| 1942| |
Capacity form/unform 1000/ MB Heads 4| 16| |
Seek time / track 15.0/ ms Sector/track | 63| |
Controller IDE / ATA2 FAST/ENHA Precompensation
Cache/Buffer 32 KB Landing Zone
Data transfer rate MB/S int Bytes/Sector 512
16.600 MB/S ext
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 55 | -40 70
Power: sleep 0.6 W Humidity % 5 90 | 5 90
standby 0.7 W Altitude km |
idle 2.6 W Shock g 10 | 100
seek W Rotation RPM 4103
read/write 4.2 W Acoustic dBA 39
spin-up W ECC Bit
MTBF h 250000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
JTS PALLADIUM P1000/1200-2AF INSTALLATION GUIDE P/N 88098-001
+---------------------------------------------------------+
| |XX
| |XXI
| |XXN
| |XXT
| |XXE
| |XXR
| |XXF
| |XXA
| |XXC
| |XXE
| |XX
| |
| |XX Power
| |XX
| |
| |+-+
| || |JP1
+---------------------------------------------------------++-+
**********************************************************************
J U M P E R S
**********************************************************************
JTS PALLADIUM P1000/1200-2AF INSTALLATION GUIDE P/N 88098-001
Jumper Setting
==============
JP1
+8-----2+ +-POWER-++---IDE-----
|o o o o| |O O O O||oooooooooooo
|o o o o| |+12 +5||1oooooooooooo
+7-----1+ \-------/+--------------
Master (Default)
-----------------
o o x o When installing only one drive, leave the jumper
o o X o in this factory set position. You can also use
this setting for the first (Master) drive, when
attaching a second (Slave) drive that conforms
ATA-2 specifications.
Master with Slave
-----------------
o x o o Use this jumper setting for the first (Master)
o X o o drive, in two drive installations where the
second (Slave) drive does NOT conform to ATA-2
(EIDE) specifications.
Slave
-----
o o o x Use this jumper setting for the setting for the
o o o X second drive of a two drive installation. Only one
of the two drives attached can have this setting.
Cable Select
------------
o o o o When using this jumper setting, the cable select
o o xxx line (pin 28) determines the assignment of Master
and Slave in two drive installations. Verify that
you have the necessary signal cable modifications
before using this jumper setting. If the select
line in your cable is not modified, use the
appropriate jumper settings for Master and Slave
above.
The first drive attached to a host adapter must be a Master.
**********************************************************************
I N S T A L L
**********************************************************************
JTS PALLADIUM JUMPER SETTING
Notes on installation
=====================
Installation direction
----------------------
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
The drive will operate in all axis (6 directions).
