W R E N V 9 4 1 8 6 - 3 2 4 IMPRIMIS
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 5.25"/FH Cylinders 1224| | |
Capacity form/unform 286/ 324 MB Heads 11| | |
Seek time / track 18.0/ 5.0 ms Sector/track | | |
Controller ESDI Precompensation
Cache/Buffer KB Landing Zone
Data transfer rate 1.250 MB/S int Bytes/Sector 512
MB/S ext
Recording method RLL 2/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 10 50 | -40 70
Power: sleep W Humidity % 8 80 | 5 95
standby W Altitude km -0.305 3.048| -0.305 12.210
idle W Shock g 2 | 32
seek 30.0 W Rotation RPM 3600
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 100000
Warranty Month
Lift/Lock/Park YES Certificates CSA,FCC,IEC380,IEC435,UL47...
**********************************************************************
L A Y O U T
**********************************************************************
SEAGATE ST4383E/ST4384E/ST4442E PRODUCT MANUAL 77765300-K
+--------------------------------------------------------+
| |XX J4
| |XX Data
| |XX Cable
| |XX
| 1-+J9 |XX
| | | |
| +-+ |XX
| Terminator+-+ |XX J3
| Resistor | | |XX Control
| Pack | | |XX Cable
| +-+ |XX
| +-+ |XX
| | |J8 |XX
| | | |XX
| | | |
| 1-+ |XX Power
| |XX J1
+--------------------------------------------------------+
**********************************************************************
J U M P E R S
**********************************************************************
SEAGATE ST4383E/ST4384E/ST4442E PRODUCT MANUAL 77765300-K
Jumper setting
==============
x = Jumpers are set at factory
J1 Power Connector
-------------------
+---+---+---+---+
| 1 | 2 | 3 | 4 |
+--++--++--++--++
| | | +---------- + 5V
| | +-------------- + 5V Return
| +------------------ +12V Return
+---------------------- +12V
J8 Drive select
-----------------
Drive 1 2 3 4 5 6 7
------+-----+-----+-----+-----+-----+-----+-----
x 1 |CLOSE|OPEN |OPEN |OPEN |OPEN |OPEN |OPEN
2 |OPEN |CLOSE|OPEN |OPEN |OPEN |OPEN |OPEN
3 |OPEN |OPEN |CLOSE|OPEN |OPEN |OPEN |OPEN
4 |OPEN |OPEN |OPEN |CLOSE|OPEN |OPEN |OPEN
5 |OPEN |OPEN |OPEN |OPEN |CLOSE|OPEN |OPEN
6 |OPEN |OPEN |OPEN |OPEN |OPEN |CLOSE|OPEN
7 |OPEN |OPEN |OPEN |OPEN |OPEN |OPEN |CLOSE
Note: Unit select zero (no jumpers) is invalid
Pins on the drive ID select and configuration select header are
provided to facilitate manual drive configuration. No devices other
than jumpers should be connected to these pins. Connection to
external devices (Switches, Connectors, etc.) could adversely affect
drive performance. Exact location of these pins and header may be
changed without notice.
Drive Select
------------
The following characteristics apply to the Drive Select lines:
1. Logical unit designation for up to 7 drives is performed during
installation by installing jumpers on pins on a connector
header on the main PWA. The jumpers are installed in a 1
through 7 position configuration to select device addresses 1
through 7. Zero is not a valid address.
2. The controller shall not attempt to select the drive until 1
second after DC power is applied. The Ready output will be
valid (whether asserted or negated) within 1 us after the drive
is selected.
3. The drive will be selected (and the Drive Selected Signal
asserted) within 1 us after the Drive Select lines contain that
unit's select address. The drive will be deselected (and the
Drive Selected signal negated) within 1 us after the Drive
Select lines contain another unit's select address.
4. The Drive Select lines must remain asserted for 1 us after a
write operation.
5. When the Drive Select lines are asserted, a head change will
occur, requiring a delay before a read or write operation can
be initiated.
J9 Motor Start on command
--------------------------
1 OPEN Spindle motor starts on power-up
(* Only on series codes above 01)
Cylinder selection set for 1,224 cylinder
(* Only on series code 01 drives)
CLOSED Spindle motor start command required to start motor
(* Only on series above 01)
Cylinder selection set for 1,412 cylinder
(* Only on series code 01 drives)
* To determine the Series Code of the drive locate the Serial Number
printed on the label in a SN xxxxxxxx format. The first two digits
denote the series code.
J9 Sector Configuration
------------------------
Sectors | 2 | 3 | 4
---------------+-------+-------+---------
64 | OPEN | OPEN | OPEN
35 | OPEN | OPEN | CLOSED
10 | OPEN | CLOSED| OPEN
36 | CLOSED| OPEN | OPEN
x 34 | CLOSED| OPEN | CLOSED
87 | CLOSED| CLOSED| OPEN
**Address mark| CLOSED| CLOSED| CLOSED
** Used with soft sectored controllers that create their own sector
boundaries.
J9 Reserved
-------------
5 OPEN RESERVED for factory test
SHOULD BE LEFT OPEN!
**********************************************************************
I N S T A L L
**********************************************************************
SEAGATE ST4383E/ST4384E/ST4442E PRODUCT MANUAL 77765300-K
Notes on installation
=====================
Drive mounting
--------------
horizontally vertically
+-----------------+ +--+ +--+ +------------------+
| | | +-----+ +-----+ | | | x
| | | | | | | | x+----------------+x
+-+-----------------+-+ | | | | | | ||x x||
+---------------------+ | | | | | | || x x ||
| | | | | | || x x ||
x x | | | | | | || x x ||
+------x------x-------+ | +-----+ +-----+ | || xx ||
+-+------x--x-------+-+ +--+ +--+ || x x ||
| xx | || x x ||
| x x | || x x ||
+---x--------x----+ |x x|
x x x++----------------++x
UNACCEPTABLE! UNACCEPTABLE!
Never install PC board on the Top!
Drive Orientation
-----------------
Only two drive mounting orientations are permitted: discs in the
horizontal plane and discs in the vertical plane. The uppermost
surface must be maintained in a level position or drive performance
may be adversely affected. In the vertical plane, the drive may be
mounted on either side, but not on either end. The drive may be not
mounted inverted (upside down) in the horizontal orientation. It is
recommended for optimum performance that data written in a given
orientation be read in that same orientation.
WREN 5 is designed, manufactured, and tested with a "Plug-in and
Play" installation philosophy. This minimizes the requirements for
highly trained personnel to integrate the WREN 5 into an OEM's
system, wether in a factory or field environment.
Cooling
-------
Cabinet cooling must be designed by the customer so that the ambient
temperature immediately surrounding the WREN 5 will not exceed
temperature limits. Specific consideration should be given to
make ensure adequate air circulation around the heat sinks on the
circuit board on the rear of the drive.
Interface Cabling Options
-------------------------
View A
+---------------------Host-Controller---------------------+
| |
|Data Control Data Control Data Control Data Control |
+--+-----+--------+-----+--------+-----+--------+-----+---+
| | | | | | | |
| | | | | | | |
| | | | | | | |
| | | | | | | |
+-++-+--++-+-+ +-++-+--++-+-+ +-++-+--++-+-+ +-++-+--++-+-+
| |T | |*T| | | |T | |*T| | | |T | |*T| | | |T | |*T| |
| +--+ +--+ | | +--+ +--+ | | +--+ +--+ | | +--+ +--+ |
|WREN OR ESDI| |WREN OR ESDI| |WREN OR ESDI| |WREN OR ESDI|
+------------+ +------------+ +------------+ +------------+
Each control cable length must not exceed 10 feet (3.00m). Each
data cable length must not exceed 10 feet (3.00m).
*T indicates removable terminator resistor pack.
WREN data ports are permanently terminated.
Radial Configuration
--------------------
View A shows each drive interfaced to its own control cable, which
allows interfacing an arbitrary number of drives and a variety of
system operational techniques. Each drive has its data cable and
control cable radially connected to the host controller. The length
of each individual cable must not exceed 10 feet (3.00 meters).
Terminator resistors must be installed in the host controller for
each data cable and for each control cable. For this configuration, a
terminator resistor pack must be installed in each WREN 5 Disc Drive.
View B
+--------------Host Controller-------------+
| |
|Data Control Data Data |
+-+------+-------+--------------+----------+
| | | |
| | | |
| | | |
| +--**---+-------+------+-------+
+++-+----+---+ +++-+-----+--+ +++-+----++-++
||T | | ||T | | ||T | |*T||
|+--+ | |+--+ | |+--+ +--+|
|WREN OR ESDI| |WREN OR ESDI| |WREN OR ESDI|
+------------+ +------------+ +------------+
Total control cable length must not exceed 10 feet (3.00m). Each
data cable length must not exceed 10 feet (3.00m).
*T indicates removable terminator resistor pack.
WREN data ports are permanently terminated.
** A maximum of 7 devices may be interconnected.
Daisychain Configuration
------------------------
A daisychain configuration incorporates a maximum of seven drives in
parallel on a common control cable. Only the drive selected by the
host system has its control and data signals enabled through this
common interface. View B shouws illustrates a daisychain of WREN 5
Disc Drives or other ESDI devices. A terminator resistor pack is
required in the host controller for each data cable. Only the last
ESDI device in the daisychain requires a terminator resistor pack for
the control cable. Terminator resistor packs for the control cable or
other drives must be removed. The total combined control cable length
(from the controller to the first drive, to the second and subsequent
drives) must not be more than 10 feet (3.00 meters).
DC Cable and Connector
----------------------
The WREN 5 receives DC power through a 4 pin right angle connector
mounted on the main circuit board. Recommended part number for the
mating connector are provided, but equivalent parts may be used.
Type of cable: 18 AWG
Connector: AMP 1-480424-0
Contacts: AMP 60619-4 (Loose Piece); AMP 61117-4 (Strip)
Data Cable and Connector
------------------------
The I/O connector for the data interface is a 20 pin board edge
connector. The odd pins are located on the back side of the printed
circuit board. The evne pins are on the front side (down) side of the
printed circuit board. A key slot is provided between pins 3 and 5.
Seagate recommends keying this connector to prevent installing it
upside down. However, the WREN will not be damaged if the connector
is installed upside down.
Recommended part numbers for the mating connector are included below,
but equivalent parts may be used.
Connector: 20 pin, 3M-3461-0001, AMP 88373-6
Cable: Flat Cable (Stranded AWG 28) 3M-3365-20
Flat Cable (Stranded AWG 28) 3M-3517-20 (Shielded
Cable)
Key: AMP 583274-1, 3M-3439-0000
Control Cable and Connector
---------------------------
The I/O connector for the control interface is a 34 pin board edge
connector. The odd pins are located on the back (up) side of the
printed circuit board and are connected to the ground plane. The even
pins are on the front (down) side of the printed circuit board. A key
slot is provided between pin 3 and 5. Seagate recommends keying this
connector to prevent installing it upside down. However, the WREN
will not be damaged if the connector is installed upside down.
Recommended part numbers for the mating connector are included below,
but equivalent parts may be used.
Connector: 34 pin, 3M-3463-0001, AMP 88373-3
Key: AMP 583274-1, 3M-3439-0000
Cable: Flat cable (Stranded AWG 28) 3M-3365-34
Flat cable (Stranded AWG 28) 3M-3517-34 (Shielded
Cable)
Spectra Strip Twist'n Flat 455-248-34 (Stranded
AWG 28 Twisted Pair)
Interface Drivers/Receivers
---------------------------
The WREN 5 uses two types of signals; single ended and balanced
differential. The data and clock signals use balanced differential
drivers and receivers. All other signals use single ended drivers and
receivers.
Single Ended Drivers/Receivers
-------------------------------
Transmitter Characteristics
The WREN 5 uses the 74F38 open collector buffer/driver to transmit
status to the host. This driver is capable of sinking a current of
40 mA with a low-level output voltage of 0.7V.
Receiver Characteristics
The WREN 5 uses the 74LS14 Hex Inverter with hysteresis gate as a
line receiver. The input of each receiver is terminated in a 150 ohm
pullup resistor.
Terminator Characteristics
The terminator is a resistor module that plugs into a socket in the
last drive in a daisychain. Each drive is furnished with a
terminator. Terminators must be removed from all except the last
drive on the cable prior to daisychain operation. An equivalent
terminator must be provided in the controller on each input signal
line from the drive to the controller. Only the control cable
resistor module is removable.
Balanced Differential Drivers/Receivers
---------------------------------------
Transmitter Characteristics
The WREN 5 uses 75158 balanced differential driver. An assertion on
the interface is defined when "+" output is more positive than the
"-" output.
Receiver Characteristics
------------------------
The WREN 5 uses 75157 type balanced differential receivers. An
assertion one on the interface is defined when the "+" input is more
positive than the "-" input.
Terminator Requirements
-----------------------
Each differential receiver in the drive is terminated with a 100 ohm
resistor. An equivalent terminator must be provided in the controller
on each input signal line from the drive to the controller.
**********************************************************************
F E A T U R E S
**********************************************************************
SEAGATE ST4383E/ST4384E/ST4442E PRODUCT MANUAL 77765300-K
Standards
---------
The WREN 5 has been developed as a system peripherals to the highest
standards of design and construction. The WREN 5 depends upon its
equipment to provide adequate power and environment in order to
achieve optimum performance and compliance with applicable industry
and governmental regualations. Special attention must be given in the
areas of safety, power distribution, shielding, audible noise
control, and temperature regulation.
The WREN 5 complies with Seagate standards.
The WREN 5 is a UL Recognized component per UL478 and a CSA Certified
product per CSA C22.2, No. 220-M1986. It also meets the requirements
of DIN IEC 380/VDE 0806/8.81, DIN IEC 435/VDE 0805/11.84 and EN
60950/09.87.
The WREN 5, as delivered, is designed for system integration before
use. It is supplied as a sub-assembly and is therefore not directly
subject to the FCC Rules and Regulations, Part 15, Subpart J
governing EMI of computing devices, and the Radio Interference
Regulations of the Canadian Department of Communications.
Media Description
-----------------
The media used in the WREN 5 has a diameter of approximately 5
inches (130 mm). The aluminum substrate is coated with a thin film
magnetic material, and lubricated to permit the heads to contact the
surface when starting and stopping.
Each data surface has either a total of 1412 tracks and is capable of
recording 29,482,560 bytes of unformatted data, or has 1224 Tracks
capable of recording 25,557,120 Bytes of unformatted data.
Media defects are characterized as correctable or uncorrectable de-
pending on the type and magnitude of the media flaw. Various error
correction codes may be implemented. The code chosen should be
consistent with Seagate media testing and certification methods. In
the WREN 5 media certification is performed using the following
standards:
An error burst of 11 bits or less is a correctable error.
An error burst greater than 11 bits in length is an un-
correctable error.
Host systems using the WREN 5 should have, as a minimum, resident
capabilities to recognize and map defective tracks and perform track
reallocation routines.
1. 1224 or 1412 total tracks per surface.
2. Tracks 0 to be error free on each data surface.
3. 30 defects per surface maximum.
4. Cumulative defects not to exceed 1 per megabyte, based on
total available unformatted drive capacity.
Drive/Receiver Characteristics
------------------------------
Logic Level Drive Output Receiver Input
--------------------------------------------------------------------
High (negated) (0) 2.5 V; 5.25 V 2.0 V; 5.25 V
Low (asserted) (1) 0.7 V; 0.0 V 0.8 V; 0.0 V
The difference in the voltages between input and output signals is
due to the losses in the cable.
Seek Time
---------
| ST4383E|ST4384E|ST4442E
----------------------------------+--------+-------+--------
Track-to-Track msec. typ. | 4 | 3 | 3
msec. max. | 5 | 4 | 4
Average msec. typ. | 18 | 14.5 | 16
Average msec. max. | 20 | 16.5 | 18
Latency msec. avg. | 8.33 | 8.33| 8.33
----------------------------------+--------+-------+--------
Seek time is defined as the elapsed time from the receipt of a seek
command until the drive signals the controller that it is ready to
perform another seek or a read/write function on the new cylinder.
Average seek time is determined by dividing the sum of the time for
all possible movements by the total number of movements.
Spindle Speed and Latency
-------------------------
The spindle speed is 3600 0.5% r/min. The speed tolerance includes
motor performance and motor control circuit tolerances.
The average latency time is 8.33 milliseconds, based on a nominal
disc speed of 3600 r/min. The maximum latency time is 16.67 milli-
seconds based on a maximum disc speed of 3564 r/min.
Read Data Transfer Rate
-----------------------
The nominal read serial data transfer rate is 10.0 Mbits per second,
1.25 Megabytes per second.
Power Sequencing
----------------
Power sequencing is not required for the WREN 5. The drive protects
against inadvertent writing during power up and down. Daisychain
operation requires that power be maintained on the terminated unit
to insure proper termination of the peripherals I/O cables.
Temperature
-----------
50*F to 122*F (10*C to 50*C) operating ambient with a maximum
gradient of 36* F (20* C) per hour. The maximum temperature is
derated linearly to 1.8* F per 1640 feet. Cabinet packaging designs
must provide ample air circulation around the WREN 5 to ensure
environmental limits are not exceeded as a result of heat transfer
from other system components. Operating Ambient is defined as the
average temperature 0.25 inch outward from the top of the drive
chassis at the middle of the drive (lengthwise). The temperature of
the top cover must not exceed 140*F (60* C) when measured at the
center of the drive.
Reliability
-----------
The following reliability specifications assume correct host/drive
operational interface implementation, including all interface
timings, power supply voltages, environmental conditions, and
appropriate data handling circuits in the host system.
MTBF 100,000 hours
Service Life 5 years
Preventive Maintenance None required