E L I T E 9 7 5 0 1 - 1 6 G IMPRIMIS
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 5.25"/FH Cylinders 2101| | |
Capacity form/unform 1370/ 1600 MB Heads 17| | |
Seek time / track 11.5/ 1.7 ms Sector/track | | |
Controller SCSI2 SINGLE-ENDED Precompensation
Cache/Buffer 256 KB SEGMENTED Landing Zone
Data transfer rate 4.500 MB/S int Bytes/Sector 512
5.000 MB/S ext
Recording method RLL 2/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C |
Power: sleep W Humidity % |
standby W Altitude km |
idle W Shock g |
seek 32.1 W Rotation RPM 5400
read/write W Acoustic dBA
spin-up W ECC Bit
MTBF h 150000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
SEAGATE ST41600/41601 PRODUCT DESCRIPTION
+---------------------------------------------------------++-+J1
| SINGLE-ENDED || |
++LED |+-+
++ |XX Power
| |XX
| |
| Terminator 1+ |XX1
| Dip || |XX SCSI
| ++ |XX
| TP+-1 |XX
| 4-+ |XX
| |XX
| |XX
| |XX
| Spindle+-+|
| Sync +-+|+-+J2
| ST41600N || |
+---------------------------------------------------------++-+
+---------------------------------------------------------++-+J1
| DIFFERENTIAL || |
++ |+-+
++LED |XX Power
| |XX
| |
| Terminator 1+ |XX1
| Dip || |XX SCSI
| ++ |XX
| TP+-1 |XX
| 4-+ |XX
| Terminator 1+ |XX
| Dip || |XX
| ++ |XX
| Spindle+-+|
| Sync +-+|+-+J2
| ST41600ND/ST41601ND || |
+---------------------------------------------------------++-+
ST41601N 2 Terminator Resistor Sips
**********************************************************************
J U M P E R S
**********************************************************************
SEAGATE ST41600N/41601 PRODUCT DESCRIPTION
Jumper Setting
==============
Spindle Sync
+4--1+ TP Ground
J2 |o oo|A 4+--+3 12V +++ 5V J1
o o o o o|o oo|B 2+--+1 | | | | o o o o
o o o o o+----++-------------------------+ +-------+ o o o o
--4-2-1----------+oooooooooooooooooooooooo1+-+ +----------
+-+-+ | | |ooooooooooooooooooooooooo| |O O O O| | | | |
SCSI | | +-SCSI-Cable-Connector----+ +-------+ | | | |
ID | | | | | |
| + Master OFF/Slave ON - Spindle Sync | | | |
+-- Write Protect option enable | | | |
| | | |
Spinup Delay (10 secs * ID) ------------------------+ | | |
Motor Start option enable ----------------------------+ | |
Parity check disable -----------------------------------+ |
Sweep Cycle enable ---------------------------------------+
SCSI ID
-------
+----------+-----------------------+
| SCSI ID | Jumpers |
| | ID4 | ID2 | ID1 |
+----------+-------+-------+-------+
|x 0 | OPEN | OPEN | OPEN |
+----------+-------+-------+-------+
| 1 | OPEN | OPEN | CLOSED|
+----------+-------+-------+-------+
| 2 | OPEN | CLOSED| OPEN |
+----------+-------+-------+-------+
| 3 | OPEN | CLOSED| CLOSED|
+----------+-------+-------+-------+
| 4 | CLOSED| OPEN | OPEN |
+----------+-------+-------+-------+
| 5 | CLOSED| OPEN | CLOSED|
+----------+-------+-------+-------+
| 6 | CLOSED| CLOSED| OPEN |
+----------+-------+-------+-------+
| 7 | CLOSED| CLOSED| CLOSED| RESERVED!
+----------+-------+-------+-------+
x = Default
TP Terminator Power
--------------------
4+-+-+3 Initiator supplies power over the SCSI Bus for
|X+-+ terminators. Drive supplies no terminator power.
2+-+-+1
4+-+-+3 Drive supplies power for its own terminator resistor-paks
+-+-+ but not to SCSI Bus. (Default)
2+xxx+1
4+-+-+3 Drive supplies power for external terminator at end of
|X|X| the daisy chain. Terminator resistor-paks must be
2+-+-+1 removed. This option is recommended only for last drive
on daisy-chain. (This option only on Single-Ended drives)