D S P - 3 1 0 7 L W AVASTOR
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 3117| | |
Capacity form/unform 1070/ 1368 MB Heads 8| | |
Seek time / track 9.5/ 1.0 ms Sector/track | | |
Controller SCSI2 SI/WI/FAST Precompensation
Cache/Buffer 512 KB SEGMENTED Landing Zone
Data transfer rate 4.000 MB/S int Bytes/Sector 512
20.000 MB/S ext SYNC
Recording method RLL 1/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 55 | -40 66
Power: sleep W Humidity % 10 90 | 8 95
standby W Altitude km -0.061 3.048| 12.192
idle 8.5 W Shock g 10 | 45
seek 10.0 W Rotation RPM 5400
read/write W Acoustic dBA 34
spin-up W ECC Bit 264
MTBF h 500000
Warranty Month
Lift/Lock/Park YES Certificates CSA,FCC,TUV,UL1950,VDE
**********************************************************************
L A Y O U T
**********************************************************************
DEC DSP3000LW/LWD SERIES PRODUCT DESCRIPTION EK-RH3CA-PD.A01
68-pin SCSI Connector (16-bit)
------------------------------
+--------------------------------------------------+
| Back View |
| |
+------------J1------------------------------J2----+
|+-------------------------+ +---Option--++-------+|
|34ooooooooooooooooooooooo1| |o o o o o 1||O O O O||
|68ooooooooooooooooooooooo35 12 o o o o o|| ||
|+-------------------------+ +-----------++-------+|
+-----------SCSI---------------------------Power---+
+ +
+--------------------------------------------------+
| Front View (Bezel End) |
| |
| Fault LED |
+--+-----------------------------------------------+
+--+---+--6+---------------------------------------+
| | |o o|Secondary Option |
+ | |ooo|Connector +
| +1--J3
Busy LED
+---------------------------------------------------------+
| TERMPWR ++ |XX J1
| HEADER ++ |XX
| |XX
| |XX
| |XX
| |XX
| |XX
| |XX
| |XX
| |XX
| J3 |+-+
|+-+Secondary || |Option
|| |Option || |
|+-+ |+-+
| |XX J2
|*Busy LED |XX Power
+---------------------------------------------------------+
**********************************************************************
J U M P E R S
**********************************************************************
DEC DSP3000LW/LWD SERIES INSTALLATION GUIDE EK-RH3CA-IG.A01
Jumper Setting
==============
TERMPWR (Terminator Power)
--------------------------
Generally, the host is the only device on the SCSI bus required to
provide TERMPWR for the bus. To ensure that there is a sufficient
level of power along the entire SCSI bus, Digital Equipment
Corporation recommends that all devices on the SCSI bus supply
TERMPWR (if they are capable). SCSI devices are protected by a diode
or similar semiconductor to prevent back flow of the terminator
power when more than one device supplies this power.
NOTE
LR Models do not provide TERMPWR to the SCSI bus. The RAID connector
does not accommodate this feature.
TERMPWR - LW/LWD Models
-----------------------
Header may ++ | To provide TERMPWR, install the
be 2-pin, ++ | TERMPWR jumper at the following
4-pin, or ++ | locations.
6-pin ++ |
+-----+-- +--+ Install shunt jumper on
---------------------------+ |xx| these pins if drive is to
XXXXXXXXXXXXXXXXXXXXXXXXX | | provide TERMPWR to SCSI bus.
SCSI Connector | |
+--+
SCSI Bus Termination
--------------------
Both ends of the SCSI bus cable must be terminated. One end is
terminated at the host. The other end must be terminated by the last
SCSI device on the SCSI bus.
Drive Termination
-----------------
DSP3000L Series drives contain internal components to provide active
termination of the SCSI bus.
When this drive is the last device on the SCSI bus, configure the
drive to enable active termination. Do so by installing a shunt
jumper at the drive's active termination header. If active
termination is not required for this drive, make sure that the
jumper is not installed.
Active Termination - LW/LWD Models
----------------------------------
+-----1+ Option
|oXoooo| Connector
|oXoooo|
12-----+
SCSI ID (Address) Selection
---------------------------
Each device on the SCSI bus must have a unique SCSI ID number
assigned to it.
ID number for L/LD models (8-bit SCSI) range from 0 through 7. For
LW/LWD models (16-bit SCSI), the numbers range from 0 through 15.
SCSI ID numbers for LR models range from 0 through 7 for 8-bit
configurations and from 0 through 15 for 16-bit configurations.
Configure the SCSI ID of L/LD/LW/LWD models by installing jumper
across the indicated Option connector pins. For LR versions, provide
the proper open or ground signal input to the referenced pins of the
drive's 80-pin RAID connector.
SCSI ID - LW/LWD Models
-----------------------
+----------+-------------------------------+ +-----1+
| SCSI ID | Jumper Location | |oooooo| Option
| | PINS | |oooooo| Connector
| | 7-8 | 5-6 | 3-4 | 1-2 | 12-----+
+----------+-------+-------+-------+-------+
| 0 | OPEN | OPEN | OPEN | OPEN |
| 1 | OPEN | OPEN | OPEN | CLOSED|
| 2 | OPEN | OPEN | CLOSED| OPEN |
| 3 | OPEN | OPEN | CLOSED| CLOSED|
| 4 | OPEN | CLOSED| OPEN | OPEN |
| 5 | OPEN | CLOSED| OPEN | CLOSED|
| 6 | OPEN | CLOSED| CLOSED| OPEN |
| 7 | OPEN | CLOSED| CLOSED| CLOSED|
| 8 | CLOSED| OPEN | OPEN | OPEN |
| 9 | CLOSED| OPEN | OPEN | CLOSED|
| 10 | CLOSED| OPEN | CLOSED| OPEN |
| 11 | CLOSED| OPEN | CLOSED| CLOSED|
| 12 | CLOSED| CLOSED| OPEN | OPEN |
| 13 | CLOSED| CLOSED| OPEN | CLOSED|
| 14 | CLOSED| CLOSED| CLOSED| OPEN |
| 15 | CLOSED| CLOSED| CLOSED| CLOSED|
+----------+-------+-------+-------+-------+
Configure Optional Features
---------------------------
CAUTION
The 5-volt signals of two or more drives should not be connected
together or to any other current source by using the Option
connector. Doing so may cause drive malfunction or component damage.
Except when connecting several drives together for a spindle
synchronization application, do not connect the ground signals of two
or more drives together or to any other current source using the
Option connector. Doing so may introduce ground loop problems.
The following optional features can be configured according to your
system requirements. These features (model-dependent) include:
- Notification of AC power failure (not currently supported by LR
models. SCSI RST may be used instead.)
- Spindle synchronization
- Write protection (not currently supported by LR models)
- Spin delay
AC Failure Notification
-----------------------
The AC Low connection (AC_LOW L) is not currently supported on LR
models, SCSI Bus Reset provides the alternative to the AC Low
warning.
The host system or power supply can warn the drive of an impending
AC failure by asserting the signal AC_LOW L. This is an active low
signal (low means power failure).
NOTE
The system should provide this warning at least 10 milliseconds prior
to failure for this feature to be operational.
To utilize the AC-LOW L warning feature, connect the system's AC
power warning signal and associated ground to the referenced AC_LOW L
and ground pins on the Option connector. When the host system assert
the AC_LOW L warning to the drive, the drive prevents write-spliced
for outstanding writes.
AC_LOW L Connection
-------------------
DSP3053LW
DSP3053LWD +-----1+
DSP3107LW |oooooo|Option Connector
DSP3107LWD +-+**oooo|
DSP3133LW | 12+----+
DSP3133LWD | +------ LOGIC_GND L
+---------- AC_LOW L
Spindle Synchronization
-----------------------
DSP3000L Series drives support synchronized spindle operation. Master
or slave synchronized operation is set through a SCSI Mode Select
Page.
When the drive operates as a Master, it generates a spindle
synchronization reference signal (SPINDLE_SYNC_REF L). When operating
as a slave, the drive synchronizes its spindle according to the
SPINDLE_SYNC_REF L input reference. The drive always maintains local
speed regulation when no reference signal is applied.
NOTE
The reference signal must originate from drives with the same
electronics modules. Fo example, connect Model DSP3107L only with
another DSP3107L drive. Do not connect the SPINDLE_SYNC_REF L signal
so that of any other model disk drive. Otherwise, the drive may mal-
function.
When connecting multiple drives together for spindle synchronization,
be sure to use proper cabling techniques to avoid ground loop
problems.
Spindle Sync Connection
-----------------------
DSP3053LW Secondary Option Connector
DSP3053LWD +2-6+
DSP3107LW |o *+--- LOGIC_GND L
DSP3107LWD |oo@+--- SPINDLE_SYNC_REF L
DSP3133LW +1-5+
DSP3133LWD
Write Protection
----------------
L/LD/LW/LWD models support either the Write Protect or Spin Delay
mode. If your drive supports the Write Protect mode, provide write
protection by installing the jumper across the referenced pins of the
Option connector.
To disable Write Protection from LW/LWD model drives, remove the
jumper accross pins 1 and 2 of the secondary Option connector.
Note that when the Write Protect Mode bit is set to a 1, automatic
spin up occurs at power on.
DSP3053LW +--6+
DSP3053LWD |X o|Secondary Option
DSP3107LW |Xoo|Connector
DSP3107LWD +1--+
DSP3133LW
DSP3133LWD
Spin Delay
----------
The method for establishing spin-up characteristics is dependent upon
the drive model.
Spin Delay - L/LD/LW/LWD Models
-------------------------------
These drives support either the Write Protect or Spin Delay mode. If
your drive supports the Spin Delay mode, you can program the drive
automatically spin-up at powere on by installing the jumper across
the referenced Option connector pins.
To have spin-up controlled by a Start/Stop Unit command, remove the
jumper.
DSP3053LW +--6+
DSP3053LWD |X o|Secondary Option
DSP3107LW |Xoo|Connector
DSP3107LWD +1--+
DSP3133LW
DSP3133LWD
Remote Features
---------------
DSP3000L Series drives support the following remote features, which
can be configured at the drive's Option connector or RAID backplane:
- Remote SCSI ID selection
- Remote LED status display
Remote SCSI ID Selection
------------------------
SCSI ID can be set remotely from an external (remote) switch or
control panel. For L/LD/LW/LWD models, this is accomplished using the
Option connector. For LR models, the output of the remote or external
ID switches takes the place of jumpers or circuits at the RAID system
backplane.
Configure L/LD/LW/LWD models for remote ID selection by removing the
SCSI ID jumpers (if present) fromn the SCSI ID pins. Then connect the
leads from the external selection switch to the referenced pins.
Observe the following guidelines while doing so.
- ID bit 0, at Pin 1, is the Least Significant Bit.
- SCSI ID bits 0, 1, 2, and 3 are active LOW signals. That is, the
bit is a 1 if the corresponding remote switch is closed to ground.
- For LW/LWD models, use pin 10 for the common ground return of all
four ID bits.
Option Connector
DSP3053LW +-----1+
DSP3053LWD |oo@@@@| * = LOGIC_GND L (Pin 10)
DSP3107LW |o*oooo| @ = SCSI ID <0>,<1>,<2>,<3> L
DSP3107LWD 12-----+ (Pins 1,3,5,7)
DSP3133LW
DSP3133LWD
Remote LED Status Display
-------------------------
Busy and Fault status for L/LD/LW/LWD models can be monitored by
connecting a remote Busy and a remote Fault display LED to the
drive's Option connector.
Remote Busy - L/LD/LW/LWD Models
--------------------------------
The remotely monitor Busy status of the drive, connect the cathode
side of the remote Busy LED to the BSY_OUT L pin. The anode side of
the LED connects to the +5 VDC OUT pin.
Remote Fault - L/LD/LW/LWD Models
---------------------------------
The remotely monitor Fault status of the drive, connect the cathode
side of the remote Fault LED to the FLT_OUT pin. The anode side of
the LED connects to the +5 VDC OUT pin.
Option Connector
DSP3053LW +-----1+
DSP3053LWD +5 VDC --+*ooooo|
DSP3107LW OUT |oo*oo*+-FLT_OUT L
DSP3107LWD 12-+---+
DSP3133LW +----- BSY_OUT L
DSP3133LWD
**********************************************************************
I N S T A L L
**********************************************************************
DEC DSP3000L SERIES INSTALLATION GUIDE EK-RH3CA-IG.A01
Notes on installation
=====================
Drive mounting
--------------
horizontally vertically
+-----------------+ +--+ +--+ +------------------+
| | | +-----+ +-----+ | | |
| | | | | | | | |+----------------+|
+-+-----------------+-+ | | | | | | || ||
+---------------------+ | | | | | | || ||
| | | | | | || ||
| | | | | | || ||
+---------------------+ | +-----+ +-----+ | || ||
+-+-----------------+-+ +--+ +--+ || ||
| | || ||
| | || ||
+-----------------+ || ||
++----------------++
You can mount the disk drive in any position. LR models mount in RAID
storage subsystems. The drive (with bezel) attaches to the system bay
and accept #6-32 screws. Screws should not exceed 0.25 inch
(6.25 millimeters) in length, otherwise damage to the PCB may result.
Mounting and Bezel Options
--------------------------
Bezels and mounting brackets are available from Digital Equipment
Corporation for mounting the drive in either 3.5-inch or 5.25-inch
form factor bays.
Combination Connector - L/LD Models
-----------------------------------
+-----------------+-----------------------------------------------+
| Part Number | Vendor |
+-----------------+-----------------------------------------------+
| 12-36486-01 | Digital Equipment Corp. |
+-----------------+-----------------------------------------------+
| 89331-001 | Berg Electronics (formerly Dupont Electronics)|
+-----------------+-----------------------------------------------+
| CWN-710-54-0119 | C.W. Industries |
+-----------------+-----------------------------------------------+
| DA-2339-25 | Methode Electronics |
+-----------------+-----------------------------------------------+
Includes 0.1-in pitch, 50-pin SCSI connector and 4-pin power
connector.
Combination Connector - LW/LWD Models
-------------------------------------
+-----------------+-----------------------------------------------+
| Part Number | Vendor |
+-----------------+-----------------------------------------------+
| 12-40413-01 | Digital Equipment Corp. |
+-----------------+-----------------------------------------------+
| 92-1814-12-1 | AMP, Inc. |
+-----------------+-----------------------------------------------+
Includes 68-pin SCSI connector, 4-pin power connector, and a
2-mm pitch, 12-pin (2x6) Option connector.
Option Connector - L/LD Models
------------------------------
+-----------------+-----------------------------------------------+
| Part Number | Vendor |
+-----------------+-----------------------------------------------+
| 12-36484-02 | Digital Equipment Corp. |
+-----------------+-----------------------------------------------+
| 90516-003 | Berg Electronics (formerly Dupont Electronics)|
+-----------------+-----------------------------------------------+
| 3-176837-3 | AMP, Inc. |
+-----------------+-----------------------------------------------+
| 87049-2091 | Molex, Inc. |
+-----------------+-----------------------------------------------+
A 2-mm pitch, 19-pin (2x10) keyed (missing pin) connector
Secondary Option Connector - LW/LWD Models
------------------------------------------
+-----------------+-----------------------------------------------+
| Part Number | Vendor |
+-----------------+-----------------------------------------------+
| 12-36484-05 | Digital Equipment Corp. |
+-----------------+-----------------------------------------------+
A 2-mm pitch, 5-pin (2x3) keyed (missing pin) connector
Shunt Jumper - All Models
-------------------------
+-----------------+-----------------------------------------------+
| Part Number | Vendor |
+-----------------+-----------------------------------------------+
| 12-36482-01 | Digital Equipment Corp. |
+-----------------+-----------------------------------------------+
| 86730-001 | Berg Electronics (formerly Dupont Electronics)|
+-----------------+-----------------------------------------------+
| LPC-SPG | Honda |
+-----------------+-----------------------------------------------+
A 2-mm pitch shunt for configuring termination characteristics
RAID Connector - LR Models
--------------------------
+-----------------+-----------------------------------------------+
| Part Number | Vendor |
+-----------------+-----------------------------------------------+
| TBS | Digital Equipment Corp. |
+-----------------+-----------------------------------------------+
DC Power and pin connector assignments
--------------------------------------
+------------+ pin 1 +12 VDC
| 4 3 2 1 | pin 2 +12 Volts Return GROUND
+------------+ pin 3 + 5 Volts Return GROUND
pin 4 + 5 VDC
**********************************************************************
F E A T U R E S
**********************************************************************
DEC DSP3000L SERIES INSTALLATION GUIDE EK-RH3CA-IG.A01
Product Summary
---------------
DSP3000L Series 3.5-inch Disk Drives are high-performance, high
capacity drives, designed and manufactures by Digital Equipment
Corporation.
Features
--------
Features of the DSP3000L Series drives include the following:
- Formatted capacity ranging from 535 MB to 1,377.5 MB, depending
upon model
- 1 millisecond track-to-track seek time
- 512 KB segmented cache buffer
- End-to-end Error Detection Code/Parity on cache RAM
- Four headers per sector
- Embedded quadrature servo
- Self-diagnostics
- Down-loadable SCSI firmware
- Tagged command queuing
- Seek ordering
- Automatic block realloction
- Glitch-free power on/off operation
- Synchronized spindle operation
- Low power consumption
Power-On Tests
--------------
After power is applied, and before spin-up is completed, the drive
performs self-test diagnostics prior to making itself visible on the
SCSI bus. These intitial self-test check most of the electronics that
control HDA, but not the SCSI transceiver or SCSI connector.
After spin-up, additional tests complete self-test coverage of the
electronics module and the HDA. The unit appears not ready to the
host between completion of the initial self-tests and completion of
the drive's post spin-up tests.
Seek Time
---------
+----------------------------------+--------+--------+--------+
| |DSP3053L|DSP3107L|DSP3133L|
+----------------------------------+--------+--------+--------+
|Track-to-Track msec. typ. | 1 | 1 | 1 |
+----------------------------------+--------+--------+--------+
|Average msec. typ. | 9.5 | 9.5 | 9.5 |
| msec. max. | 20 | 20 | 20 |
+----------------------------------+--------+--------+--------+
|Latency msec. avg. | 5.6 | 5.6 | 5.6 |
+----------------------------------+--------+--------+--------+
LED Indicators
--------------
The green Busy LED illuminates to signify the drive is working on a
SCSI command. The amber Fault LED indicates a fault status.
Both the Busy and Fault indicators light briefly during power up.
This serves as a hardware and lamp test.
During a calibration operation, the Busy LED is illuminated and the
Fault LED flashes. Calibrations occur following some firmware up-
grades. Generally, calibration periods last only about five minutes,
after which the drive comes on-line and both indicators go out.
If the Fault indicator lights at any other time, the drive has failed
and likely requires service (unless the Fault LED was turned on by
means of a MODE SELECT command).
Remote Busy and Fault indicators can be connected to the Option
connector to provide status display at a remote location or panel.
