SIMPLE TECHNOLOGY, INC.

COMMUNICATOR 33.6, COMMUNICATOR 33.6 WITH SIMPLEJACK, STI-FAX/33.6, STI-FAX/33.6SJ

Card Type

Modem (asynchronous)

Chipset

Unidentified

I/O Options

Voice

Maximum Data Rate

33.6Kbps

Maximum Fax Rate

14.4Kbps

Data Modulation

Bell 103A, 212A

ITU-T V.21, V.22bis, V.23, V.32, V.32bis, V.34

Rockwell V.FC

Fax Modulation

ITU-T V.17, V.27ter, V.29

Error Correction/Compression

MNP5, MNP10EC, V.42, V.42bis

Fax Class

Class I & II

Data Bus

PCMCIA Type II

53852

SUPPORTED STANDARD COMMANDS

Basic AT Commands

+++, ‘comma’, A/

A, B, E, H, L, M, N, O, P, Q, T, V, W, X, Y, Z

&C, &D, &F, &G, &K, &P, &Q, &R, &S, &T, &V, &W, &Y, &Z

Extended AT Commands

\A, \B, \G, \K, \N

%C, %E, %L, %Q

Special AT Commands

:E, *H, -K, )M, @M, +MS, -Q

S-Registers

S0, S1, S2, S3, S4, S5, S6, S7, S8, S9, S10, S11, S12, S14, S16, S18, S21, S22, S23, S24, S25

S26, S27, S29, S30, S31, S32, S33, S36, S38, S46, S48, S82, S86, S95, S201

Note: See MHI help file for complete information.

Proprietary AT Command Set

BIT-MAPPED REGISTER S210

Format:

AT [cmds] S210=n [cmds]

Default:

13

Range:

0 - 13

Description:

Controls V.34 baud rate and V.34 asymmetric mode.

Bit

Value

Function

2 - 0

000

001

010

011

100

í 101

V.34 mode may use 2400 baud rate only.

V.34 mode may use 2400 baud rate only.

V.34 mode may use 2400 or 2800 baud rates.

V.34 mode may use 2400, 2800, or 3000 baud rates.

V.34 mode may use 2400, 2800, 3000, or 3200 baud rates.

V.34 mode may use 2400, 2800, 3000, 3200, or 3429 baud rates.

3

0

í 1

V.34 asymmetric mode disabled.

V.34 asymmetric mode enabled.

DISTINCTIVE RING

Format:

AT [cmds] -SDRn [cmds]

Default:

Unidentified

Range:

0 - 7

Description:

Selects which distinctive ring signals the modem will respond to.

Bit

Value

Function

0

0

1

Do not respond to distinctive ring type 1.

Respond to distinctive ring type 1.

1

0

1

Do not respond to distinctive ring type 2.

Respond to distinctive ring type 2.

2

0

1

Do not respond to distinctive ring type 3.

Respond to distinctive ring type 3.

FIRMWARE DOWNLOAD

Type:

Configuration

Format:

AT [cmds] **

Description:

Downloads new code to the firmware flash memory in ASCII format.

MNP10EC MODE

Type:

Configuration

Format:

AT [cmds] -SEC=m,n [cmds]

Description:

Selects whether the modem will attempt to use MNP10EC mode during the handshaking sequence.

Command

Function

m=0

MNP10EC handshaking disabled unless a V.34 connection is attempted via a cellular line.

í -m=1

MNP10EC handshaking enabled.

n

Default:

Unidentified

 

Range:

-10 to -30

 

Unit:

-1 dBm

 

Description:

Sets the initial transmission level.

See SIMPLE TECHNOLOGY, INC. 28.8 COMMUNICATOR for a full command summary.

Hosted by uCoz