DECISION COMPUTER INTERNATIONAL CO., LTD.

PCCOM 16-BIT ISA 4-PORT RS-232

Card Type

Serial

Chipset

GoldStar

I/O Options

Serial port

Data Bus

16-bit ISA

CONNECTIONS

Function

Label

Serial ports via DB-37 port

J1

Note:Standard DB-25 serial ports are provided on an included adapter cable.

USER CONFIGURABLE SETTINGS

Setting

Label

Position

Port 1 enabled

JP1/H

Open

 

Port 1 disabled

JP1/H

Closed

Port 2 enabled

JP2/H

Open

 

Port 2 disabled

JP2/H

Closed

Port 3 enabled

JP3/H

Open

 

Port 3 disabled

JP3/H

Closed

Port 4 enabled

JP4/H

Open

 

Port 4 disabled

JP4/H

Closed

Interrupt vector enabled

JP5/K

Closed

 

Interrupt vector disabled

JP5/K

Open

Trigger interrupt on low signal

JP9

Open

 

Trigger interrupt on high signal

JP9

Closed

PORT ADDRESSES

Setting

JP1/A

JP1/B

JP1/C

JP1/D

JP1/E

JP1/F

JP1/G

 

000h

Closed

Closed

Closed

Closed

Closed

Closed

Closed

 

008h

Closed

Closed

Closed

Closed

Closed

Closed

Open

 

010h

Closed

Closed

Closed

Closed

Closed

Open

Closed

 

018h

Closed

Closed

Closed

Closed

Closed

Open

Open

 

020h

Closed

Closed

Closed

Closed

Open

Closed

Closed

2A0h (port 1)

Open

Closed

Open

Closed

Open

Closed

Closed

2A8h (port 2)

Open

Closed

Open

Closed

Open

Closed

Open

2B0h (port 3)

Open

Closed

Open

Closed

Open

Open

Closed

2B8h (port 4)

Open

Closed

Open

Closed

Open

Open

Open

 

3D8h

Open

Open

Open

Open

Closed

Open

Open

 

3E0h

Open

Open

Open

Open

Open

Closed

Closed

 

3E8h

Open

Open

Open

Open

Open

Closed

Open

 

3F0h

Open

Open

Open

Open

Open

Open

Closed

 

3F8h

Open

Open

Open

Open

Open

Open

Open

Note:JP1 sets the address for port 1. The settings for JP2 through JP4 are identical and set the addresses for ports 2 through 4, respectively.

A total of 128 base address settings are available. The jumpers are a binary representation of the decimal memory addresses. JP1/A is the Most Significant Bit and jumper JP1/G is the Least Significant Bit. The jumpers have the following decimal values: JP1/A=512, JP1/B=256, JP1/C=128, JP1/D=64, JP1/E=32, JP1/F=16, JP1/G=8. Open the jumpers and add the values of the jumpers that are open to obtain the correct memory address. (Open=1, Closed=0)

INTERRUPT VECTOR

Setting

JP5/A

JP5/B

JP5/C

JP5/D

JP5/E

 

000h

Closed

Closed

Closed

Closed

Closed

 

001h

Closed

Closed

Closed

Closed

Closed

 

002h

Closed

Closed

Closed

Closed

Closed

 

003h

Closed

Closed

Closed

Closed

Closed

 

004h

Closed

Closed

Closed

Closed

Closed

2BFh

Open

Closed

Open

Closed

Open

 

3FBh

Open

Open

Open

Open

Open

 

3FCh

Open

Open

Open

Open

Open

 

3FDh

Open

Open

Open

Open

Open

 

3FEh

Open

Open

Open

Open

Open

 

3FFh

Open

Open

Open

Open

Open

INTERRUPT VECTOR (CONT)

Setting

JP5/F

JP5/G

JP5/H

JP5/I

JP5/J

 

000h

Closed

Closed

Closed

Closed

Closed

 

001h

Closed

Closed

Closed

Closed

Open

 

002h

Closed

Closed

Closed

Open

Closed

 

003h

Closed

Closed

Closed

Open

Open

 

004h

Closed

Closed

Open

Closed

Closed

2BFh

Open

Open

Open

Open

Open

 

3FBh

Open

Open

Closed

Open

Open

 

3FCh

Open

Open

Open

Closed

Closed

 

3FDh

Open

Open

Open

Closed

Open

 

3FEh

Open

Open

Open

Open

Closed

 

3FFh

Open

Open

Open

Open

Open

Note:A total of 1024 vector address settings are available. The jumpers are a binary representation of the decimal memory addresses. JP5/A is the Most Significant Bit and jumper JP5/J is the Least Significant Bit. The jumpers have the following decimal values: JP5/A=512, JP5/B=256, JP5/C=128, JP5/D=64, JP5/E=32, JP5/F=16, JP5/G=8, JP5/H=4, JP5/I=2, JP5/J=1. Open the jumpers and add the values of the jumpers that are open to obtain the correct address. (Open=1, Closed=0)

INTERRUPT SELECTION

Setting

JP6CH1/A

JP6CH1/B

JP6CH1/C

JP6CH1/D

JP6CH1/E

 

IR/FONT>

Open

Open

Open

Open

Open

 

IRQ3

Open

Open

Open

Open

Open

 

IRQ4

Open

Open

Open

Open

Open

IRQ5

Open

Open

Open

Open

Open

 

IRQ7

Open

Open

Open

Open

Open

 

IRQ10

Open

Open

Open

Open

Closed

 

IRQ11

Open

Open

Open

Closed

Open

 

IRQ12

Open

Open

Closed

Open

Open

 

IRQ14

Open

Closed

Open

Open

Open

 

IRQ15

Closed

Open

Open

Open

Open

INTERRUPT SELECTION (CONT)

Setting

JP6CH1/F

JP6CH1/G

JP6CH1/H

JP6CH1/I

JP6CH1/J

 

IR/FONT>

Open

Open

Open

Open

Closed

 

IRQ3

Open

Open

Open

Closed

Open

 

IRQ4

Open

Open

Closed

Open

Open

IRQ5

Open

Closed

Open

Open

Open

 

IRQ7

Closed

Open

Open

Open

Open

 

IRQ10

Open

Open

Open

Open

Open

 

IRQ11

Open

Open

Open

Open

Open

 

IRQ12

Open

Open

Open

Open

Open

 

IRQ14

Open

Open

Open

Open

Open

 

IRQ15

Open

Open

Open

Open

Open

Note:JP6CH1 sets the address for port 1. The settings for JP6CH2 through JP6CH4 are identical and set the addresses for ports 2 through 4, respectively.

INTERRUPT ENABLE

Setting

JP7/A

JP7/B

JP7/C

JP7/D

JP7/E

 

IR/FONT>

Open

Open

Open

Open

Open

 

IRQ3

Open

Open

Open

Open

Open

 

IRQ4

Open

Open

Open

Open

Open

IRQ5

Open

Open

Open

Open

Open

 

IRQ7

Open

Open

Open

Open

Open

 

IRQ10

Open

Open

Open

Open

Closed

 

IRQ11

Open

Open

Open

Closed

Open

 

IRQ12

Open

Open

Closed

Open

Open

 

IRQ14

Open

Closed

Open

Open

Open

 

IRQ15

Closed

Open

Open

Open

Open

INTERRUPT ENABLE (CONT)

Setting

JP7/F

JP7/G

JP7/H

JP7/I

JP7/J

 

IR/FONT>

Open

Open

Open

Open

Closed

 

IRQ3

Open

Open

Open

Closed

Open

 

IRQ4

Open

Open

Closed

Open

Open

IRQ5

Open

Closed

Open

Open

Open

 

IRQ7

Closed

Open

Open

Open

Open

 

IRQ10

Open

Open

Open

Open

Open

 

IRQ11

Open

Open

Open

Open

Open

 

IRQ12

Open

Open

Open

Open

Open

 

IRQ14

Open

Open

Open

Open

Open

 

IRQ15

Open

Open

Open

Open

Open

Note:Jumpers on JP7 should be set to match all the interrupts selected with jumpers JP6CH1 through JP6CH4. If multiple boards are installed and on the same interrupt, only the first board should have JP7 set. Additional boards should have JP7 left open.

BUS SPEED

Setting

JP8/A

JP8/B

JP8/C

JP8/D

8MHz or slower

Closed

Open

Open

Open

12MHz or slower

Open

Closed

Open

Open

25MHz or slower

Open

Open

Closed

Open

33MHz or faster

Open

Open

Open

Closed

Hosted by uCoz