S D - 3 1 0 5 - 3 0 TEAC
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 3.5"/SLIMLINE Cylinders 1282| 926| 776| 641
Capacity form/unform 105/ MB Heads 4| 13| 8| 8
Seek time / track 19.0/ 8.0 ms Sector/track 40| 17| 33| 40
Controller IDE / AT Precompensation
Cache/Buffer 64 KB READ-AHEAD Landing Zone
Data transfer rate 1.563 MB/S int Bytes/Sector 512
MB/S ext
Recording method RLL 2/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 5 50 | -40 60
Power: sleep 0.1 W Humidity % 8 80 | 8 80
standby 0.3 W Altitude km |
idle 2.9 W Shock g 5 | 70
seek 5.1 W Rotation RPM 3600
read/write 3.3 W Acoustic dBA
spin-up W ECC Bit
MTBF h 30000
Warranty Month 12
Lift/Lock/Park YES Certificates CSA,TUV,UL478
**********************************************************************
L A Y O U T
**********************************************************************
TEAC SD-3105-30 RIGID DISK DRIVE 10530580-09 REV. A
+---------------------------------------------------------++-+Strap
| |+-+S0 3
| |XX1
| |XXSignal-
| |XXCon.
| |XX
| |XX
| |XX
|++LED |XX
|++ |XX
| |XX
| |xx
| |XX Power
| |
| |XX Power
| |XX
+---------------------------------------------------------+
**********************************************************************
J U M P E R S
**********************************************************************
TEAC SD-3105-30 RIGID DISK DRIVE 10530580-09 REV. A
Jumper Setting
==============
Indicator LED
-------------
The indicator (LED) on the front bezel lights up while the HDD
executes a command. An external LED can also be lighted through the
-SLV/ACT signal terminal on the same condition by setting the strap
S0 to ON.
Straps
------
The setting method for the straps, S1 and S2, should be changed
according to the number of the HDDs connected as shown in the
following table.
Functions of straps
+----------+-------------------------------------------------------+
| Strap No.| Function |
+----------+-------------------------------------------------------+
| S0 | Changes over the function of the -SLV/ACT output |
| | signal. |
| | ON : The -ACTIVE signal is selected. The external LED|
| | can be lighted up at the -SLV/ACT signal |
| | terminal. |
| | OFF : The -SLAVE PRESENT signal is selected. |
+----------+-------------------------------------------------------+
| S1 | Selects whether one HDD is used singly, or two HDDs |
| | are used in daisy chain connection. |
| | ON : Two HDDs are used. |
| | OFF : Only one HDD is used. |
+----------+-------------------------------------------------------+
| S2 | Selects the master drive or slave drive. |
| | OFF : Only one unit used, or master drive with two |
| | units used. |
| | ON : Slave drive with two units used. |
+----------+-------------------------------------------------------+
| S3 | Changes over the -I/O CH RDY output signal. |
| | OFF : The -I/O CH RDY signal is not output. |
| | ON : The -I/O CH RDY signal is output. |
+----------+-------------------------------------------------------+
Notes: 1. ON : Strap short
OFF : Strap open
2. At the shipping of the HDD, the strap S0 is set to ON, S1
to OFF, S2 to ON, S3 to ON.
How to set the straps, S1 and S2
--------------------------------
+-------------------------+--------------+-----+-----+
|Number of HDDs connected | Master/Slave | S1 | S2 |
+-------------------------+--------------+-----+-----+
| 1 | - | OFF | ON |
+-------------------------+--------------+-----+-----+
| 2 | Master | ON | ON |
| | Slave | ON | OFF |
+-------------------------+--------------+-----+-----+
**********************************************************************
I N S T A L L
**********************************************************************
TEAC SD-3105-30 RIGID DISK DRIVE 10530580-09 REV. A
Notes on Installation
=====================
Installation direction
----------------------
horizontally vertically
+-----------------+ +--+ +--+
| | | +-----+ +-----+ |
| | | | | | | |
+-+-----------------+-+ | | | | | |
+---------------------+ | | | | | |
| | | | | |
| | | | | |
+---------------------+ | +-----+ +-----+ |
+-+-----------------+-+ +--+ +--+
| |
| |
+-----------------+
Any of the four directions can be used.
The mounting cabinet for the HDD should be constructed so that no
distortion may be produced in the chassis.
A space of at least 1.5mm must be allowed between the mounting
cabinet and the PCBA of the HDD.
An insulation sheet should be stuck to the PCBA mounting face of the
HDD mounting cabinet, as required.
In each mounted position, the front can be raised by up to 30*.
Mounting positions other than those shown must be discussed
separately.
Screws
------
The HDD is fixed with screws through the mounting holes at the
3-#6-32UNC 4 deep each side.
4-#6-32UNC 4 deep bottom.
