M 9 3 8 0 S MINISCRIBE
NO MORE PRODUCED Native| Translation
------+-----+-----+-----
Form 5.25"/FH Cylinders 1218| | |
Capacity form/unform 319/ 362 MB Heads 15| | |
Seek time / track 16.0/ 3.5 ms Sector/track 36| | |
Controller SCSI1 SINGLE-ENDED Precompensation 65535
Cache/Buffer KB Landing Zone
Data transfer rate 1.250 MB/S int Bytes/Sector 512
4.000 MB/S ext
Recording method RLL 2/7 operating | non-operating
-------------+--------------
Supply voltage 5/12 V Temperature *C 10 50 | -40 60
Power: sleep W Humidity % 8 80 | 8 80
standby W Altitude km -0.061 3.048|
idle 18.0 W Shock g 2 | 35
seek W Rotation RPM 3600
read/write W Acoustic dBA 47
spin-up W ECC Bit
MTBF h 50000
Warranty Month
Lift/Lock/Park YES Certificates
**********************************************************************
L A Y O U T
**********************************************************************
MINISC. 9380S PRODUCT MANUAL P/N 1093 REV. P8, SEPTEMBER 12, 1988
+--------J9-J10-J11---------------------------------------+
| +-+-+-+ J601 2+1 |
| +-+-+-+ +---+21 J602 J701+++++ |XX J4
| J7 J12 J13 3-2-1-+ || |XX
| RP702| |XX I
| J29 J510 J21 J20 || |XX N
| +--J6-+ +++++ ++ |XX T
| +-----+ +++++ ++ |XX E
| J24+J30 || |XX R
| +++ RP701| |XX F
| J14+J27 || |XX A
| ++ |XX C
| +-+ |XX E
| | J8 |XX
| | | |XX
| | | |
| | | |XX J3
| +-+ |XX Power
+---------------------------------------------------------+
**********************************************************************
J U M P E R S
**********************************************************************
MINISC. 9380S PRODUCT MANUAL P/N 1093 REV. P8, SEPTEMBER 12, 1988
Jumper Setting
==============
Additional Jumper Definitions
-----------------------------
J7 - Start/Stop Spindle Motor Enable
J9 - Diagnostic Jumper
J10/J11 - Head Configuration
J12 - Sector Setting
J13 - Sector Setting
THESE SEVEN (7) JUMPERS MUST BE INSTALLED FOR DRIVE OPERATION:
--------------------------------------------------------------
J14, J20, J21, J24, J27, J29, J30
RP701/RP702 - Terminator Resistors
J601 SCSI ID
-------------
+----------+-----------------------+
| SCSI ID | Jumper J16 |
| |J601-1 |J601-2 |J601-3 |
+----------+-------+-------+-------+
| 0 | OPEN | OPEN | OPEN |
| 1 | OPEN | OPEN | CLOSED|
| 2 | OPEN | CLOSED| OPEN |
| 3 | OPEN | CLOSED| CLOSED|
| 4 | CLOSED| OPEN | OPEN |
| 5 | CLOSED| OPEN | CLOSED|
| 6 | CLOSED| CLOSED| OPEN |
| 7 | CLOSED| CLOSED| CLOSED|
+----------+-------+-------+-------+
J602 SCSI parity enable
------------------------
J602 is a group of two pairs of jumper pins. The first pair is
presently undefined. The second pair defines SCSI parity enable, as
follows:
J602-2
OPEN SCSI Parity Enabled
CLOSED SCSI Parity Disabled
J701 SCSI Terminator Power
---------------------------
J701 is a group of two pairs of jumper pins. The first pair controls
terminator power supplied by the target while the second pair control
power supplied from elsewhere on the bus.
J701-1 J701-2
CLOSED OPEN Local Terminator Power
OPEN CLOSED Remote Terminator Power
Option Jumpers and Test Point Description
-----------------------------------------
J7 Start/Stop Spindle Motor Enable
J9 Diagnostic Jumper
J10, J11 Head Configuration
J10/J11 Heads
--------------
J10 CLOSED
J11 CLOSED 13 Heads
J10 CLOSED
J11 OPEN 7 Heads
J10 OPEN
J11 CLOSED 11 Heads
J10 OPEN
J11 OPEN 15 Heads - 35 Sectors = Hard sector
J12/J13/J19 Sectors
--------------------
J12 J13 J19 Sectors Bytes U Bytes F
-----------------------------------------------------------
OPEN OPEN OPEN 35 - Hard sector 594 512
OPEN CLOSED OPEN 36 578 512
CLOSED OPEN OPEN 34 612 530
CLOSED CLOSED CLOSED Soft(Controller will select Sector #)
(Novell, Sector = 36)
**********************************************************************
I N S T A L L
**********************************************************************
MINISC. 9380S PRODUCT MANUAL P/N 1093 REV. P8, SPETEMBER 12, 1988
Notes on Installation
=====================
Mounting Orientation
--------------------
The MiniScribe 9000 Series uses industry-standard mounting for
5-1/4" Winchester Disk Drives. The 9000 Series are designed to be
used in applications where the unit may experience shock and
vibration at greater levels than larger and heavier disk drives.
The drive may be mounted in any attitude.
The 9000 drive is mounted using 6-32 UNC screws 1/4" maximum
penetration. The customer must allow adequate ventilation to the
drive to insure reliable operation.
In as much as the drive frame acts as a heat sink to dissipate heat
from the unit, the enclosure and mounting structure should be
designed to allow natural convection of heat around the HDA and
outer frame. If the enclosure is small or if natural convection is
restricted, a fan may be required.
Daisy Chaining the MiniScribe 9000 Drives
-----------------------------------------
Up to seven 9000 Series drives may be connected to a single host
controller/formatter. Control signals at J1 are transmitted via
standard, daisy-chain interconnection. Data signals at J2 are trans-
mitted via radially connected data-transfer lines.
Note: Interface terminators RP4 and RP17 are installed only in the
last physical drive in the control chain. Maximum number of drives =
7.
J4 SCSI Connector
------------------
J4 is a 50-pin straight solder pin connector on the printed circuit
board. This cable connector is used to send and receive information
from the SCSI Host Adapter with keyed slots between pins 3 and 5, 23,
25 and 27, and 47 and 49.
Recommended Mating Connector: Burndy FRS50BF-8P or equivalent.
Recommended cable is a Belden 50 pin flat cable, part number 9LS8050
or equivalent.
J3 DC Power Connector
----------------------
J3 is a 4 pin keyed connector on the printed circuit board. DC power
(+5V and +12V) is supplied to the drive via this connector.
Recommend connector: AMP 350543-1
Pins: AMP 350078-4
Note 1: Equivalent of the above are permissible.
Note 2. Suggested wire size 18 AWG.
Electrical Interface
--------------------
SCSI uses single-ended drivers and receivers which allow a maximum
cable length of 20 feet (6 meters) from the first to the last device
(up to 8 devices) on the bus.
All assigned signals are terminated with 220 ohms to +5 volts and
330 ohms to ground at each end of the cable. Both two (2) terminator
networks on the 9380S are removable.
All signals driven by the drive are open collector and have the
output characteristics as follows.
Signal Assertion 0.0 VDC to 0.8 VDC
Max. Driver Output 48mA (sinking) at @ 0.5 VDC
Signal Negation 2.5 to 5.25 VDC
All signals received by the drive shall have the following input
characteristics.
Signal True 0.0 V DC to 0.8 V DC
Maximum Total Input Load -0.4 mA @ 0.4 V DC
Signal False 2.5 to 5.25 V DC
Minimum Input Hyteresis 0.2 V DC
**********************************************************************
F E A T U R E S
**********************************************************************
MINISC. 9380S PRODUCT MANUAL P/N 1093 REV. P8, SEPTEMBER 12, 1988
Introduction
------------
The MiniScribe 9000 Series of disk drives are low cost, high
capacity, high performance random access storage devices utilizing
5 1/4" this film disks as storage media. Each disk surface employs
one moveable head to access the data tracks. The 9000 Series
features capacities of 380 megabytes (unformatted storage capacity).
The 9000 disk drives utilize advanced 3380 Whitney-type head flexures
and sliders which allow closer spacing of disks, allowing a higher
number of disks in a standard 5 1/4" package.
Seek Time (including settling time)
-----------------------------------
+----------------------------------+--------+
| | 9000 |
+----------------------------------+--------+
|Single Track msec. max. | 3.5 |
+----------------------------------+--------+
|Average msec. typ. | 16 |
|1/3 Stroke Seek time msec. max. | 17 |
|Full Stroke Seek time msec. max. | 35 |
|Rezero msec. max. | 250 |
+----------------------------------+--------+
|Latency msec. avg. | 8.33 |
+----------------------------------+--------+
Media Defect Criteria (as shipped from MiniScribe)
--------------------------------------------------
Maximum Defects* 275
2 bytes in length
Cylinder zero defect free
*A single defect is defined as being less than 2 bytes long. A
multiple defect is defined as 2 bytes or longer, or as a track with
more than 1 single defect.
Caution/Warning
---------------
The Miniscribe drive is a precision product. During handling the unit
must not be dropped, jarred or bumped. Otherwise, damage to the heads
and disks may occur. When the drive is removed from the Miniscribe
shipping container and not immediately secured within a chassis
through its shock mounts, it must be stored on a padded, grounded,
antistatic surface.
Failure to comply with the above procedure will render null and void
all warranties.
